Table of Contents
Advertisement
b.
C.
Press HOLD button
to place outside
par-
ties on hold.
Hold timer starts.
If one of
the two paxties is internal,
that party
will
be dropped.
Press CONF
and hang
up or press
the
ON/OFF
button
to leave the other confer-
ence parties still connected
in an unsuper-
vised conference.
CONF button
will flash
and timer will start.
There will be a wam-
ing tone
before
the
other
parties
are
dropped.
Re-entering
a Conference
When
the controller
re-enters
the conference,
the disconnect
timer is reset.
a Lift handset
to re-enter
a monitored
con-
ference.
b. To re-enter
a conference
placed
on hold,
repeat steps for establishing
a conference.
c. To re-enter
an unsupetised
conference,
lift handset
(multi-line);
or to re-enter
an
unsupervised
conference,
lift handset
and
press flashing
CONF button
(add-on).
The
CONF button
lights steady and confirma-
tion tone will be heard.
Terminating
a Conference:
a. Replace
handset
or push ON/OFF
button
to off. You must be actively in the confer-
ence.
400.22
DO NOT DISTURB
Activating
Do Not Disturb
If you have been given the ability to place your
phone
in Do Not Disturb:
a, Press the DND button.
b. DND button
lights steady.
The
DND
button
can be pressed
while
the
phone
is ringing
to stop the ringing.
Removing
Do Not Disturb
1. Press DND button.
2. The button
LED extinguishes.
400.23
$UISWG
A station
can queue only one line at a time.
If
you see that
a particular
outside
line is busy
and you wish to be placed on a list waiting
for
that line to become
available:
To place a Queue
a, Press LINE QUE button
b. Press desired busy outside
line button.
c. Hang
up.
Infinite
816
Key Telephone
System
OPERATION
To Cancel a Queue
a. Lift handset
or press ON/OFF
button.
b. Press LINE QUE button.
c. Intercom
dial tone will be heard.
To Answer
a Queue
If you hear ringing
and an outside
line of the
line group
you queued
is slow flashing:
a Lift handset.
b. Press flashing
outside
line button
to an-
swer.
If your station
has been programmed
for Pre-
ferred Line Answer, you will have the line auto-
matically
upon lifting the handset.
400.24
STORING
STATION
SPEED NUM-
BERS
Station
Speed numbers
can be entered
by key-
set users.
System
Speed
numbers
must
be
entered
by the first programmed
attendant.
If
no attendant
is spectied,
enter at Station
1.
a. Lift handset
or press ON/OFF
button.
b. Press AUTO/SAVE
button
twice.
c. Press SIA/SPD
button
where
number
is
to be stored.
(LED will not light).
d. Select desired
outside
line or one will be
chosen automatically.
e. Dial telephone
number.
f. Press HOLD button.
g. Hang up.
-
Dialing
an [*I initiates
a Pulse-To-
Tone switchover.
-
Pressing the (#I during
number
stor-
age inserts
a Pause.
-
Pressing the FLASH key inserts
a
Flash into the speed number.
-
Pressing the CONF button
inserts
a
no-display
character
causing
any
numbers
put into the bin after the
CONF button
is pressed
not to ap-
pear on the Key Telephones
display
when the bin is accessed.
NOTE: It is in-pm&d
to ensure unused
CO lines
me prog mmmed
inio a separate
line group
SO
the system will
not
choose an undesired
CO line
when airtempting
to dial a speed bin rum-her.
400.25
DIALING
A STATION
SPEED NUM-
BER
lf no outside
l!ne has been specified
in pro-
gramming,
one will be chosen automatically
or
you can choose one now.
a Press AUTO/SAVE
button.
Issue
1, January
1992
400-5
Advertisement
Table of Contents
