Sony DVW-A500P/1 Operation Manual page 57

4-3 TC Menu
Setting time code
Before starting the procedure below for setting time
data, set the [F6] (TCG SOURCE) button to int, the
[F7] (TCG MODE) button to prst, and the [F10]
(VITC) button to on. When not recording VITC, set
the [F10] (VITC) button to off.
Note
Set the [F8] (RUN MODE) button to rec before setting
the time data for recording. When you select rec, time
data advances from a set value only during recording.
When you select free, time code advances in real time
after the initial value has been set.
1 4 2
Setting time code
1
Press the [F1] (TIMER SEL) button to select the
TC (time code) to be set.
2
Enter the new setting in the data entry window
with the numeric buttons.
For example, to enter 01H00M30S00F, press 1, 0,
0, 3, 0, 0, 0. (The leading 0 is not required. When
the entered value is less than eight digits, the
leading digit(s) is (are) set to 0 when you press the
SET button.)
D O L B Y N R C H . C O N D DIGITÅL
T I M E R
S E L G R E E N
T C L O C K
T C R V I T C P L Å Y
T I M E R
01 04 58
R E S E T
Ó µ
Å I N 0 0 : 0 0 : 0 0 : 0 0 Å O U T 0 0 : 0 0 : 0 0 : 0 0
T I M E R
I N 0 0 : 0 0 : 0 0 : 0 0
S E T
T I M E R
H O L D
o f f
T C T C G T C G R U N
S E L S O U R C E M O D E M O D E
V I T C i n t p r s t r e c
4-20
Chapter 4 Menu Settings
3
T C
Data entry
0 1 0 0 3 0 0 0
window
4 F D F 1
00
ß ƒ
O U T 0 0 : 0 0 : 0 0 : 0 0
D F / N D F V I T C
D F o n
To cancel entered value
Press the CLR button.
3
Press the SET button to set the entered
value.
If you pressed the + or – button, then entered a
value, the result of calculation appears in the
display.
D O L B Y N R C H . C O N D DIGITÅL
T I M E R
S E L G R E E N S E T
T C L O C K
T C R V I T C P L Å Y 4 F D F 1
T I M E R
01 04 58
R E S E T
Ó µ
Å I N 0 0 : 0 0 : 0 0 : 0 0 Å O U T 0 0 : 0 0 : 0 0 : 0 0
T I M E R
I N 0 0 : 0 0 : 0 0 : 0 0 O U T 0 0 : 0 0 : 0 0 : 0 0
S E T
T I M E R
H O L D
o f f
T C T C G T C G R U N
D F / N D F
S E L S O U R C E M O D E M O D E
V I T C i n t p r s t r e c
4
Press the [F3] (TIMER SET) button.
The input value is set as the time code and appears
in the time data display section.
D O L B Y N R C H . C O N D
T I M E R
S E L G R E E N
T C
T C R V I T C P L Å Y
T I M E R
01 00
R E S E T
Ó
Å I N 0 0 : 0 0 : 0 0 : 0 0 Å O U T 0 0 : 0 0 : 0 0 : 0 0
T I M E R
I N 0 0 : 0 0 : 0 0 : 0 0
S E T
T I M E R
H O L D
o f f
T C T C G T C G
S E L S O U R C E M O D E
V I T C i n t p r s t
Notes
• Time code from an external time code generator
cannot be set.
• Time code cannot be set when the internal time code
generator is locked to external time codes or time
codes read by the time code reader.
SET is displayed.
T C
0 1 0 0 3 0 0 0
00
ß ƒ
V I T C
D F o n
DIGITÅL T C
0 1 0 0 3 0 0 0
L O C K
4 F D F 1
30 00
µ ß ƒ
O U T 0 0 : 0 0 : 0 0 : 0 0
R U N
D F / N D F V I T C
M O D E
r e c D F o n