Yamaha FJR13AY 2009 Service Manual page 123

1. Grip warmer couplers
2. Hand shift switch couplers
3. Handlebar switch couplers
4. Right grip warmer lead
5. Right handlebar switch lead
6. Main switch lead
7. Hand shift switch lead
8. Left grip warmer lead
9. Left handlebar switch lead
10. Stator coil lead
11. Fuel tank breather hose (joint to rollover valve) (for
California only)
12. Air filter case breather hose
13. Gear position sensor lead
14. Foot shift switch lead
15. Fuel tank breather/overflow hose (except for
California)
16. Fuel tank overflow hose (for California only)
17. Clutch hose
18. Sidestand switch
19. Sidestand switch lead
20. Oil level switch lead
21. Rollover valve (for California only)
22. Fuel tank breather hose (rollover valve to canister)
(for California only)
23. Canister breather hose (for California only)
24. Canister (for California only)
25. Canister purge hose (3-way joint to canister) (for
California only)
26. Coolant reservoir breather hose
27. Brake hose (brake pipe/upper joint assembly to left
front brake caliper)
28. Front wheel sensor
29. Front wheel sensor lead
30. Front left turn signal/position light lead
31. Brake pipe (metering valve to right front brake
caliper)
32. Brake pipe (brake pipe/upper joint assembly to
front brake calipers)
33. Brake pipe (front brake master cylinder to brake
pipe/lower joint assembly)
34. Wire harness
35. Crankshaft position sensor lead
36. Starter motor lead
37. Neutral switch coupler
38. YCC-S speed sensor coupler
39. Oil level switch coupler
40. Upper crankcase
41. Rear balancer cover
A. Secure the plastic band by inserting the projection
on the band into the hole in the windshield drive
unit/meter assembly stay, and then fasten the
handlebar switch leads, grip warmer leads, and
hand shift switch leads with the band, making sure
that the end of the band faces down. Do not cut off
the excess end of the plastic band.
CABLE ROUTING (FJR13AE)
B. Secure the plastic band by inserting the projection
on the band into the hole in the windshield drive
unit/meter assembly stay, and then fasten the
handlebar switch leads, grip warmer leads, hand
shift switch leads and front wheel sensor lead with
the band, making sure that the end of the band
faces down. Do not cut off the excess end of the
plastic band.
C. Fasten the leads (to oil level switch and crankshaft
position sensor) that branch off from the wire
harness to the guide on the holder with a plastic
locking tie, making sure that the end of the tie faces
upward. Do not cut off the excess end of the plastic
locking tie.
D. Fasten the sidestand switch lead, stator coil lead,
and oil level switch lead with a plastic locking tie,
making sure to bundle and fasten the sidestand
switch lead so that the coupler is positioned to the
front of the tie. Face the end of the plastic locking
tie outward. Do not cut off the excess end of the
plastic locking tie.
E. To fuel tank
F. Pass the fuel tank breather/overflow hose through
the guide on the universal joint dust cover.
G. Pass the air filter case breather hose through the
guide on the muffler bracket.
H. Fasten the clutch hose with the pivot shaft locknut
retainer.
I. Pass the fuel tank breather hose (joint to rollover
valve) between the frame and the projection on the
air filter case as shown in the illustration. (for
California only)
J. Pass the canister purge hose (3-way joint to
canister) through the opening in the frame, to the
inside of the frame. (for California only)
K. Pass the fuel tank breather hose (joint to rollover
valve) through the cutout in the air deflector. (for
California only)
L. Route the coolant reservoir breather hose to the
outside of the fuel tank breather hose (joint to
rollover valve) and the canister purge hose (3-way
joint to canister). (for California only)
–
M. 43 53 mm (1.69
–
N. 60 70 mm (2.36
O. Fasten the grommets on the front wheel sensor
lead and the brake hose (brake pipe/upper joint
assembly to left front brake caliper) with the holder.
P. Pass the front wheel sensor lead through the
guide.
Q. Fasten the grommet on the front wheel sensor lead
with the holder.
R. Route the front wheel sensor lead between the left
front brake caliper and the brake hose (brake
pipe/upper joint assembly to left front brake
caliper).
S. Fasten the front wheel sensor lead to the brake
hose (brake pipe/upper joint assembly to left front
brake caliper) with the two holders, making sure to
position the lead to the inside of the hose.
T. Route the fuel tank breather/overflow hose to the
front of the clutch hose, then through the opening
between the frame and the swingarm.
U. Face the ends of the clamp to the left, making sure
that the lower end contacts the wire harness.
V. Fasten the oil level switch lead and starter motor
lead with the clamp.
W. To sidestand switch
X. Route the starter motor lead between the rear
balancer cover bolt and the rib on the crankcase.
2-74
–
2.09 in)
–
2.76 in)