Panasonic AW-RP605 Operating Instructions Manual page 5

Parts and their functions
$ Control panel
OPERATE
ON
OFF
INCOM
LEVEL
IRIS
AUTO
MANU
LOCK
: GAIN [AUTO/MAN] button
This is used to select the camera's gain control mode in
the pan-tilt head system currently selected.
Each time it is pressed, the AUTO mode or MANUAL
mode is selected in turn.
In the AUTO mode, the button's lamp comes on; in the
MANUAL mode it goes off.
If, in the AUTO mode, the R/B GAIN/PED button is
pressed and the gain is adjusted, the maximum gain can
be set to one of two levels: AGC L or AGC H.
If, in the MANUAL mode, the R/B GAIN/PED button is
pressed and the gain is adjusted, any setting from 0 dB to
the night eye mode can be selected for the gain.
; MODE [BAR/CAM] button
This is used to select the camera's video output signals in
the pan-tilt head system currently selected.
Each time it is pressed, the camera's color bar signals or
video signals are selected in turn.
When the color bar signals are selected, the button's
lamp comes on; when the video signals are selected, it
goes off.
< DATA SET button
At times when the multi-function controller has not
recognized a particular pan-tilt head system, such as
when the power to the pan-tilt head systemis turned on
or when a particular pan-tilt head system has been
connected after the multi-function controller's OPERATE
switch has been set to ON, select the pan-tilt head
system concerned, and then press the DATA SET button.
The power of the selected pan-tilt head system will be
turned on, and the camera's initial settings will be started.
< ; : = >
IRIS ZOOM FOCUS
OPEN TELE FAR WHITE AWC
BAL
GAIN
AUTO
A
MANU
MODE
BAR NG
B
CAM OK
ABC
DATA SET
ATW
CALL
TR/PSET M.LOCK 1 2 3
CLOSE WIDE NEAR
TR
PSET
TELE
MEMORY 11 12 13
EMPTY
21 22 23
IRIS
FOCUS
31 32 33
41 42 43
CLOSE OPEN
NEAR WIDE FAR
ZOOM/FOCUS/IRIS
LIMIT
ON
CAMERA CONTROL
LAMP DEF
LCD
CONTRAST
START
R/B
POINT
CAMERA
GAIN/PED MENU OK
CONTROL
TRACING/PRESET MEMORY
4 5 6 7 8 9 10 PRIORITY
14 15 16 17 18 19 20
SPEED
LOW
FULL
HIGH
24 25 26 27 28 29 130
IRIS
FOCUS
L
34 35 36 37 38 39 40
44 45 46 47 48 49 50
CLOSE
NEAR
LIMIT
OFF
= WHITE BAL [A/B/ATW] buttons
These are used to select the camera's white balance
adjustment in the pan-tilt head system currently selected.
A : When the A button is pressed, the white balance
status entered in the camera's memory A is
established, and the A button's lamp comes on.
If the AWC button is pressed after the A button
was pressed, the white balance is automatically
adjusted and entered in the camera's memory A.
B : When the B button is pressed, the white balance
status entered in the camera's memory B is
established, and the B button's lamp comes on.
If the AWC button is pressed after the B button
was pressed, the white balance is automatically
adjusted and entered in the camera's memory B.
ATW : When the ATW button is pressed, the white
balance is set to the automatic adjustment mode,
and the ATW button's lamp comes on.
> AWC button
When the WHITE BAL [A] button or [B] button has been
selected, press the AWC button to automatically adjust
the white balance and enter the adjustment in the
camera's memory A or memory B.
While the white balance is being adjusted, the AWC
button's lamp flashes; when it has been adjusted
properly, it goes off. It comes on when it was not possible
to perform the adjustment.
<Notes>
O This function does not work if the MODE button has
been set to BAR (the MODE button's lamp is lighted)
or if ATW has been selected.
O It may not be possible to adjust the white balance if
there is no white object on the screen being shot.
O If a pan-tilt head other than the AW-PH350 is being
used, the AWC button's lamp also goes off if the white
balance was not adjusted properly.
5
PAN/TILT SET
WIP H/F EXT ND OPTION
TRACING MEMORY
START/STOP RESTORE RESET
TALLY
1 2 3 4 5 AUX
CONTROL/PREVIEW MONITOR OUT SEL
UP
R
OPEN
DOWN FAR
PAN/TILT/FOCUS/IRIS