Panasonic AW-RP605 Operating Instructions Manual page 13

Parts and their functions
$ Main unit
?
8 INCOM connector
This connector is used for connecting to the TALLY &
INCOM connector on the AW-SW300 live switcher, etc.
to enable inter-communication.
To perform inter-communication,
communication system plug (Mini DIN 6-pin) supplied.
Pin No.
6 5
4 3
1
2 1
2
3
4
5
6
9 CONTROL OUT TO PAN/TILT HEAD connectors [1] to [5]
Connect these connectors to the IP/RP connector on the
AW-PH350 pan-tilt head using a straight cable equivalent
to 10BaseT (UTP category 5). The connection distance
can be extended up to 1,000 meters.
When connecting one of these connectors to any other
pan-tilt head, use the RS-232C/RS-422 converter, and
connect the connector to the RS-232C control connector
on the pan-tilt head.
: TALLY connectors [1] to [5]
These connectors are used for connection with the
TALLY connector of a special effects generator, video
switcher or other equipments.
When the voltage which is supplied to terminal numbers
1 through 5 is set to the GND level, the TALLY lamps on
the control panels and the TALLY lamps on the pan-tilt
heads come on.
; G/L IN connector (automatic 75Ω termination)
When the pan-tilt head system cameras are to be
synchronized with external signals for use, connect a
coaxial cable to this connector, and supply a black burst
signal or VBS (video, burst and sync) signal.
When a coaxial cable is connected to the 75Ω AUTO
connector, the 75Ω termination is turned off.
; <
G/L
IN
75Ω
AUTO
EXT/
AUX
SERVICE
IN
75Ω
PREVIEW
MONITOR
OUT 1
REMOTE
PREVIEW
MONITOR
OUT 2
PREVIEW
MONITOR
OUT 3
5 4 3
5 4 3 2 1
CONTROL OUT
TALLY
TO PAN/TILT HEAD
: > = 9
use the inter-
Signal
RECEIVE +
RECEIVE –
TALK +
TALK –
———
———
TO PAN/TILT
HEAD
VIDEO
/Y
IN
Pr
IN
Pb
IN
OPTION
CARD
G/L
OUT
VIDEO
/Y
OUT
Pr
OUT
Pb
OUT
TERMINATION
TALK - + TALK
6 5
4 3
2 1
OFF ON
RECEIVE - + RECEIVE
2 1 EXTERNAL 3
INCOM
CONTROL
CONTROL IN
OUT
TO CONTOROL PANEL
8
< 75Ω AUTO connector
The black burst signal or VBS (video, burst and sync)
signal which is supplied to the G/L IN connector is output
from this connector by way of a loop-through format.
= AUX IN 75Ω connector
A coaxial cable is connected to this connector to supply
the line view signals, etc. from a special effects
generator, etc.
When the CONTROL/MONITOR OUT SEL AUX button
on the control panel is pressed, the signals supplied to
the AUX IN 75Ω connector are output from the PREVIEW
MONITOR OUT 1, 2 and 3 connectors.
> PREVIEW MONITOR OUT connectors 1, 2 and 3
One end of a coaxial cable is connected to one of these
connectors and the other end is connected to the video
input connector on a TV monitor.
When the CONTROL/MONITOR OUT SEL 1 to 5 buttons
on the control panel are pressed, the video signals from
the selected pan-tilt head system are output.
When the AUX button has been pressed, the signals
supplied to the AUX IN 75Ω connector are output.
<Note>
The signals which are output from these connectors are
used for image verification purposes.
representing the actual quality of the images shot by the
camera are output from the VIDEO/Y OUT, Pr OUT and
Pb OUT connectors.
? EXT/SERVICE connector
This connector is intended to support additional functions.
It is not supported at the present time.
13
DC POWER
ON
OFF
- +
1 4
2 3
DC 12V IN
PUSH
GND
CONTROL PANEL
POWER OUT
2 1
Signals