Panasonic AW-RP605 Operating Instructions Manual page 27

Operation
Subcarrier phase adjustment
The subcarrier phase adjustment must be performed, when
composite signals have been set as the video input signals
and the pictures are to be switched by a video switcher or
other equipments.
This adjustment is not necessary when component signals
have been set as the video input signals.
1. Select the pan-tilt
CONTROL/PREVIEW MONITOR OUT SEL button.
2. Connect the video switcher or other equipments to the
VIDEO/Y OUT connector on the main unit that
corresponds to the currently selected pan-tilt head
system, and connect a color monitor to the video output
connector on the video switcher or other equipments.
3. Press the MODE button to establish the BAR mode and
switch the output signals from the convertible camera to
color bar signals.
4. Press the MENU button, turn the menu setting control
(main), and set it so that the G/L SETTING item appears
at the top of the LCD panel.
G G / / L L S S E E T T T T I I N N G G
5. Press the OK button.
The following item appears on the LCD panel.
C C A A B B L L E E L L E E N N G G T T H H
6. Turn the menu setting control (main), and set it so that
the following item appears on the LCD panel.
S S C C P P H H A A S S E E
C C O O A A R R S S E E : : 1 1
7. Output both the color bar signals (signals from inside the
switcher or other equipments) serving as the reference
and the color bar signals from the camera to the color
monitor.
8. Align the phase of the color bar signals from the camera
with the phase of the color bar signals serving as the
reference.
Use the menu setting control (L) to adjust the phase in
90-degree increments and then the menu setting control
(R) to make fine adjustments.
head system using
O O K K K K e e y y
n
S S H H O O R R T T
F F I I N N E E : : ± ± 0 0
Color bar signals from the
camera
Partition line
Color bar signals from the
switcher or other
equipments
9. Select the next pan-tilt head system using the
CONTROL/PREVIEW MONITOR OUT SEL button, and
continue adjusting the subcarrier phase in each system
concerned.
3
the
OPERATE IRIS ZOOM FOCUS
OPEN TELE FAR WHITE
GAIN BAL
AUTO
ON A
MANU
MODE
BAR
B
OFF CAM
DATA SET
INCOM
ATW
CALL
1
TR/PSET M.LOCK
CLOSE WIDE NEAR
LEVEL
IRIS TR
PSET
TELE 11
MEMORY
AUTO
MANU
LOCK
EMPTY
21
IRIS
FOCUS
31
41
CLOSE OPEN
NEAR WIDE FAR
ZOOM/FOCUS/IRIS
LIMIT
ON
27
4•6 5
8 8 4
CAMERA CONTROL
AWC
LAMP DEF WIP
LCD
CONTRAST
TRACING MEMORY
NG
OK
START
ABC R/B POINT START/STOP
CAMERA MENU OK
GAIN/PED
CONTROL
TRACING/PRESET MEMORY
2 3 4 5 6 7 8 9 10
PRIORITY
1 2
CONTROL/PREVIEW MONITOR OUT SEL
12 13 14 15 16 17 18 19 20
SPEED
LOW
FULL
HIGH
22 23 24 25 26 27 28 29 130
IRIS
FOCUS
L
32 33 34 35 36 37 38 39 40
42 43 44 45 46 47 48 49 50
CLOSE
NEAR
PAN/TILT/FOCUS/IRIS
LIMIT
OFF
1
PAN/TILT SET
H/F EXT ND OPTION
RESTORE RESET
TALLY
3 4 5 AUX
UP
R
OPEN
DOWN FAR