Panasonic AW-RP605 Operating Instructions Manual page 23

Operation
Adjusting the cable compensation manually
When composite signals are used
1. Select the pan-tilt
CONTROL/PREVIEW MONITOR OUT SEL button.
2. Connect a waveform monitor to the VIDEO/Y OUT
connector on the main unit corresponding to the pan-tilt
head system currently selected.
3. Press the MODE button to establish the BAR mode and
switch the output signals from the convertible camera to
color bar signals.
4. Press the MENU button, turn the menu setting control
(main), and set it so that the CABLE COMP item
appears at the top of the LCD panel.
C C A A B B L L E E C C O O M M P P
n
5. Press the OK button.
The following item appears on the LCD panel.
C C A A B B L L E E C C O O M M P P A A U U T T O O
S S T T A A R R T T ? ? n
6. Turn the menu setting control (main), and set it so that
the following item appears on the LCD panel.
C C A A B B L L E E C C O O M M P P M M A A N N U U A A L L
Y Y : : 0 0
3
CAMERA CONTROL
OPERATE IRIS ZOOM FOCUS
OPEN TELE FAR WHITE AWC
GAIN BAL
AUTO
ON A
MANU
MODE
BAR NG
B
OFF
CAM OK
ABC
DATA SET
INCOM
ATW
TRACING/PRESET MEMORY
CALL
1 2 3 4
TR/PSET M.LOCK
CLOSE WIDE NEAR
LEVEL
TR
IRIS
PSET
TELE
MEMORY 11 12 13 14
AUTO
MANU
LOCK
EMPTY
21 22 23 24
IRIS
FOCUS
31 32 33 34
41 42 43 44
CLOSE OPEN
NEAR WIDE FAR
ZOOM/FOCUS/IRIS
LIMIT
ON
head system using
O O K K K K e e y y
O O K K K K e e y y
C C : : 0 0
4•6•9
5
7•10 4 1
PAN/TILT SET
LAMP DEF WIP H/F EXT ND OPTION
LCD
CONTRAST
TRACING MEMORY
START
R/B
POINT START/STOP RESTORE RESET
CAMERA
GAIN/PED MENU OK
CONTROL
TALLY
5 6 7 8 9 10
PRIORITY
1 2 3 4 5 AUX
CONTROL/PREVIEW MONITOR OUT SEL
15 16 17 18 19 20 UP
SPEED
LOW
FULL
HIGH
25 26 27 28 29 130
IRIS
FOCUS
L R
35 36 37 38 39 40
45 46 47 48 49 50
CLOSE OPEN
NEAR DOWN FAR
PAN/TILT/FOCUS/IRIS
LIMIT
OFF
7. Adjust the luminance signal using the menu setting
control (L) and the chrominance signal using the menu
the
setting control (R).
Adjust the luminance and chrominance signals several
times to the signal waveforms shown below.
<Note>
In the luminance and chrominance signal adjustments
performed by the multi-function controller, the level
cannot be reduced below the level of the input signals
from the camera.
It may not be possible to perform these adjustments if
the length of the cables from the pan-tilt heads to the
main unit of the multi-function controller are too short.
8. Select the next pan-tilt head system using the
CONTROL/PREVIEW MONITOR OUT SEL button, and
continue adjusting the cable compensation in each
system concerned.
IRE
100
90
80
+77
70
60
50
40
30
+20
20
10
0
–10
–20
–20
–30
–40
– I
IRE
100
90
80
70
60
50
40
30
20 +20
10
0
–10
–20
–20
–30
–40
23
+20
–20
White
+ Q
Black
+100
+20
–20