Panasonic AW-RP605 Operating Instructions Manual page 32

Operation
Entering the tracing memory data
1. Select the pan-tilt
CONTROL/PREVIEW MONITOR OUT SEL button.
2. Use the following buttons to establish the modes.
O Press the IRIS button to establish the MANU mode
(the IRIS button's lamp now goes off).
If the AUTO mode is established, the lens iris position
will not be entered.
O Press the TR/PSET button to establish the tracing
memory mode (the TR/PSET button's lamp now
comes on).
O If the M.LOCK button's lamp lights, press the
M.LOCK button to establish the memory entry mode
(the M.LOCK button's lamp now goes off).
3. Operate the ZOOM lever and PAN/TILT lever, and on
the monitor now check the pictures which are to be shot.
4. Select the white balance from among the A, B and ATW
buttons, and adjust the lens iris using the FOCUS/IRIS
dial.
5. Press the START POINT button.
The lamps of those buttons among TRACING/PRESET
MEMORY buttons 1 through 10 in which data can be
entered now come on.
<Note>
If any button's lamp remains off, it means that data has
already been entered into that button. To enter data into
a button whose lamp is off, delete the data in the
memory first, and then proceed.
6. Press the button into which data is to be entered.
Only the lamp of the button which was pressed comes
on, and the data is entered as the start position of the
tracing memory.
<Note>
If the PAN/TILT lever is now operated, the entry mode
will be canceled.
7. Press the START/STOP button.
The START/STOP button's lamp flashes, and the entry
standby mode is established.
<Note>
When the START/STOP button is now pressed, the
entry mode will be canceled.
4
2 4 3 2 2
OPERATE IRIS ZOOM FOCUS
OPEN TELE FAR WHITE
AWC
GAIN BAL
AUTO
A
ON
MANU
MODE
BAR NG
B
OFF CAM OK
ABC
DATA SET
INCOM
ATW
TRACING/PRESET MEMORY
CALL
1 2 3 4
TR/PSET M.LOCK
CLOSE WIDE NEAR
LEVEL
TR
IRIS
TELE PSET
MEMORY 11 12 13 14
AUTO
MANU
LOCK
EMPTY
21 22 23 24
IRIS
FOCUS
31 32 33 34
41 42 43 44
CLOSE OPEN
NEAR WIDE FAR
ZOOM/FOCUS/IRIS
LIMIT
ON
head system using
(4)
6 5•7 1 3
CAMERA CONTROL PAN/TILT SET
LAMP DEF WIP H/F EXT ND OPTION
LCD
CONTRAST
TRACING MEMORY
START
R/B
POINT START/STOP RESTORE RESET
CAMERA
GAIN/PED MENU OK
CONTROL
TALLY
5 6 7 8 9 10
PRIORITY
1 2 3 4 5 AUX
CONTROL/PREVIEW MONITOR OUT SEL
15 16 17 18 19 20 UP
SPEED
LOW
FULL
HIGH
25 26 27 28 29 130
IRIS
FOCUS
L R
35 36 37 38 39 40
45 46 47 48 49 50
CLOSE OPEN
NEAR DOWN FAR
PAN/TILT/FOCUS/IRIS
LIMIT
OFF
8. The entry in the tracing memory commences as soon as
the
the pan, tilt, zoom, focus, iris or white balance mode
selection is initiated so proceed with the entry operation.
The START/STOP button stops flashing and comes on,
and the lamps of TRACING/PRESET MEMORY buttons
11 through 30 come on to provide a general guideline of
the time for which data can be entered.
Each of the No. 11 through No. 20 buttons indicates a
time of approximately 3 seconds; and each of the No. 21
through No. 30 buttons indicates a time of approximately
30 seconds.
The lamps of buttons No. 20 and above go off
approximately every 3 seconds to indicate the remaining
time during which data can be entered in the memories.
As soon as the lamp in button No. 11 goes off, the
buzzer sounds, and the tracing memory entry is
completed.
<Notes>
O Press the START/STOP button to suspend the
tracing memory entry at any time. The operations
performed up until the entry was stopped are entered
as the tracing memory data.
O The buzzer sounds when tracing memory entry is
started or suspended and when data entry is
completed.
9. If necessary,
TRACING/PRESET MEMORY buttons 1 through 10 as
tracing memory data.
10. Select the next pan-tilt head system using the
CONTROL/PREVIEW MONITOR OUT SEL button, and
continue setting the tracing memory data for each
system concerned.
Example of remaining time display
: Indicates that a button's lamp is lighted.
21 seconds
1 2
11 12
21 22
45 seconds
1 2
11 12
21 22
When data has been entered into the tracing memories,
the data will also be saved in the pan-tilt head's
memories. Therefore, when the pan-tilt head has been
replaced with another head, enter the data into the tracing
memories of the head now in use.
32
enter the other operations
3 4 5 6 7 8 9 10
13 14 15 16 17 18 19 20
23 24 25 26 27 28 29 30
3 4 5 6 7 8 9 10
13 14 15 16 17 18 19 20
23 24 25 26 27 28 29 30
into