Video Signal Cable Compensation - Panasonic AW-RP605 Operating Instructions Manual

Operation

$ Video signal cable compensation

Signal deterioration caused by the length of the cables from
the pan-tilt head to the main unit is compensated for.
When the length of the cables from the pan-tilt head to the
main unit exceeds 500 meters, set the cable compensation
switch inside the pan-tilt head to ON.
For further details, refer to the operating instructions of the
pan-tilt head.
Automatically adjusting the cable compensation
1. Select the pan-tilt
CONTROL/PREVIEW MONITOR OUT SEL button.
2. Press the MENU button, turn the menu setting control
(main), and set it so that the CABLE COMP item
appears at the top of the LCD panel.
C C A A B B L L E E C C O O M M P P
3. Press the OK button.
The following item appears on the LCD panel.
C C A A B B L L E E C C O O M M P P A A U U T T O O
S S T T A A R R T T ? ? n
4. Press the OK button.
The adjustment of the cable compensation for the
currently selected pan-tilt head system commences, and
the OK button's lamp flashes.
If composite signals have been set as the video input
signals, the output signals from the convertible camera
are switched to color bar signals, and automatic
adjustment is performed.
Alternatively, if component signals have been set as the
video input signals, the output signals from the
convertible camera are switched to color bar signals of
Y/C signals, and automatic adjustment is performed.
C C A A B B L L E E C C O O M M P P A A U U T T O O
A A U U T T O O A A D D J J U U S S T T
5. Upon completion of the adjustment, the OK button's
lamp goes off. The following item appears on the LCD
panel.
C C A A B B L L E E C C O O M M P P A A U U T T O O
A A D D J J U U S S T T O O K K
6. Select the next pan-tilt head system using the
CONTROL/PREVIEW MONITOR OUT SEL button, and
continue adjusting the cable compensation for each
system concerned.
<Note>
A small error may arise in the automatic adjustment. If
precise adjustment is required, perform the adjustment
manually. (Refer to the following page.)
head system using
O O K K K K e e y y
n
O O K K K K e e y y
If the automatic adjustment was not performed properly,
the following item appears on the LCD panel.
C C A A B B L L E E C C O O M M P P A A U U T T O O
A A D D J J U U S S T T N N G G
Check the connection of the output signals from the
convertible camera and cables, and proceed with the
automatic adjustment again.
If the automatic adjustment was not performed properly
the
again even by following the automatic adjustment
procedure, perform the adjustment manually instead.
Consult your dealer if the adjustment still cannot be
performed properly even when the manual procedure is
followed.
OPERATE IRIS ZOOM FOCUS
OPEN TELE FAR WHITE
AWC
GAIN BAL
AUTO
ON A
MANU
MODE
BAR
B
OFF
CAM
ABC
DATA SET
INCOM
ATW
CALL
TR/PSET M.LOCK 1 2
CLOSE WIDE NEAR
LEVEL
TR
IRIS
PSET
TELE
MEMORY 11 12
AUTO
MANU
LOCK
EMPTY
21 22
IRIS
FOCUS
31 32
41 42
CLOSE OPEN
NEAR WIDE FAR
ZOOM/FOCUS/IRIS
LIMIT
ON
22
2 3•4
2 1
CAMERA CONTROL PAN/TILT SET
LAMP DEF WIP H/F
LCD
CONTRAST
TRACING MEMORY
NG
OK
START
R/B
POINT START/STOP
CAMERA
GAIN/PED MENU OK
CONTROL
TALLY
TRACING/PRESET MEMORY
3 4 5 6 7 8 9 10 PRIORITY
1 2 3
CONTROL/PREVIEW MONITOR OUT SEL
13 14 15 16 17 18 19 20 UP
SPEED
LOW
FULL
HIGH
23 24 25 26 27 28 29 130
IRIS
FOCUS
L
33 34 35 36 37 38 39 40
43 44 45 46 47 48 49 50
CLOSE
NEAR DOWN
PAN/TILT/FOCUS/IRIS
LIMIT
OFF
EXT ND OPTION
RESTORE RESET
4 5 AUX
R
OPEN
FAR