Table of Contents
Advertisement
Set Up Alarm Mode 3
This table is used to set up the alarm function of each alarm input.
This enables display of the alarmed picture on the assigned monitor(s), moves the Pan/Tilt head to the preset position and
controls the auxiliary switches.
There is a total of 110 programmable alarm functions available through 10 pages of tables.
Note: To be able to set up this table, the Alarm Mode on the Alarm Mode Select table must be set to Off.
To program or edit an Alarm Mode 3, do the following:
1. Move the cursor to position 4 by moving the Joystick Controller, then press the CAM (SET) key to execute the selection.
2. Move the cursor to position 5 by moving the Joystick Controller, then press the Function F4 button to open the Pop Up
4
Window.
Move the cursor with the Joystick Controller to the desired Auto Reset time (30, 60, 90, 120, 150, 180, Off) in the Pop Up
Window, and then press the CAM (SET) key to execute the selection.
3. To select an Auto Reset time other than those displayed in the Pop Up Window in 1-second increments or decrements
between 1 to 60 seconds, leave the cursor on 30 or 60 and press the INC +1CAM or DEC –1CAM button.
....57
58
59
....27
28
29
4. Move the cursor to position 6 by moving the Joystick Controller.
Press the Function F4 button to open the Pop Up Window.
Select the desired spot or sequence mode to be assigned to the monitor by moving the Joystick Controller, and then press
the CAM (SET) key to execute the selection.
5. Move the cursor to position 7 by moving the Joystick Controller.
Enter the desired alarm number (1-128) by pressing the Numeric keys.
6. Move the cursor to position 8 by moving the Joystick Controller.
Press the Function F4 button to open the Pop Up Window.
Select the desired spot or sequence mode by moving the Joystick Controller.
If a Tour or Group sequence is selected, use the Numeric keys to select a particular Tour or Group sequence number.
Press the CAM (SET) key to execute the selection.
7. Move the cursor to position 9 by moving the Joystick Controller.
If the spot mode was selected in step 5, enter the desired camera number (1-128) by pressing the Numeric keys.
8. Move the cursor to position 10 by moving the Joystick Controller.
If the spot mode was selected in step 5, enter the desired preset position number, if applicable, by pressing the Numeric
keys.
9. Move the cursor to position 11 by moving the Joystick Controller.
If the spot mode was selected in step 5, enter the desired dwell time (1-30) by pressing the Numeric keys.
10. Move the cursor to position 12 by moving the Joystick Controller.
If the spot mode was selected in step 5, press the Function F4 button to open the Pop Up Window.
Select AUX On or Off by moving the Joystick Controller, and then press the CAM (SET) key to execute the selection.
11. Move the cursor to position 13 by moving the Joystick Controller.
Press the Function F4 button to open the Pop Up Window.
Select either Set or Reset by moving the Joystick Controller, and then press the CAM (SET) key to execute the selection.
Note: An "E" (Error) will appear in the table if an attempt is made to assign an incompatible mode to a monitor. For exam-
ple, if an attempt is made to assign a Tour sequence to a monitor that is designated as a Spot monitor.
12. Press the MON (ESC) key to escape from the programming mode. The cursor returns to position 4.
79
S e t
U p
P R O G .
S e t
U p
A l a r m
A u t o
R S T
6 0 s e c
A L
M O D E
C A M
P R E
0 1
S
0 1
0 1
1
0 2
S
0 2
2
0 3
T 0 1
3
0 4
G 0 1
0 5
S
0 3
0 2
4
0 5
T 0 2
0 5
G 0 2
5
0 6
T 0 3
0 7
G 0 3
6
0 8
G 0 4
S . . S p o t
T . . T o u r
G . . G r o u p
F 1 : N e x t
P a g e
60
90
120
150
30
31
32
33....
A l a r m
M o d e 3
M o d e 3
A U X
1
2
3
4
5
6
D W E L L
1 2
S
T
G
G
S
T
1 0
0 5
1 0
. . O n
. . O f f
F 2 : P r e
P a g e
F 3 : D E L
180
Off
P a g e
0 1 o f 1 0
7
8
9
1 0 1 1 1 2 1 3 1 4 1 5 1 6
G
G
S
G
G
G
G
G
E
E
E
E
. . O K
E . . E r r o r
* . . S e t
F 4 : P o p
U p
Hide quick links:
Advertisement
Table of Contents
