Sharp AR-M350N Service Manual page 228

2. AR-NC5J setup items
After completion of installation, perform setup of the environmental variables. Explanations on the variables are given below.
A. General
Name
Telnet Web page
Change root Change Admin
Password password
Print status after Print status after
Boot-up Boot-up
B. TCP/IP and related items
Name
Telnet Web page
TCP/IP Protocol TCP/IP Protocol TCP/IP protocol
DHCP/BOOTP DHCP/BOOTP
RARP RARP
IP Address IP Address
Subnet Mask Subnet Mask
Default Default
Gateway Gateway
Use FTP/LPD Use FTP/LPD
Banner Banner
C. NetWare and related items
Name
Telnet Web page
Netware Netware
Protocol Protocol
Frame Type Frame Type
Operation Mode Operation Mode Operation Mode PSERVER
Printer Name Printer Name
Print Server Print Server
Name Name
Factory setup
NIC Manager
Admin Sharp
Password
Print status after NO
Boot-up
Factory setup
NIC Manager
ENABLE
is used.
DHCP/BOOTP ENABLE
is used.
RARP is used. ENABLE
IP Address 0.0.0.0
Subnet Mask 0.0.0.0
Default 0.0.0.0
Gateway
Use FTP/LPD NO
Banner
Factory setup
NIC Manager
Use Netware ENABLE
Protocol.
Frame Type 802.2
Printer Name "SCxxxxxx-prn1"
(xxxxxx is the lower 6
digits of Mac address.)
Print Server "SCxxxxxx"
Name (xxxxxx is the lower 6
digits of Mac address.)
AR-NC5J/NC5JG/NC5JW - 4
Descriptions
The administrator password of the AR-NC5J is set with ASCII
character codes. This password is used for identification when
changing setup by Telnet, a Web page, or a setup utility.
Remark: Indicated as "*" for security.
When booting the AR-NC5J, select whether to print the status page or
not.
Descriptions
Used to enable/disable TCP/IP protocol. This setup will affect the
operations of LPR, FTP, TELNET, SNMP, HTTP, and the setup utility
(for TCP/IP).
Used to enable/disable the operation of DHCP/BOOTP protocol. The
DHCP/BOOTP protocol acquires an IP address from the DHCP server
or the BOOTP server when booting. To set an IP address of the AR-
NC5J, a DHCP server or a BOOTP server which has been properly
set should be operating in the sub network. The AR-NC5J
automatically recognizes DHCP and BOOTP, and employs as its
address whichever replies to it first.
Use to disable/enable the RARP protocol operation. The RARP
protocol acquires an IP address from the RARP server. To set an IP
address of the AR-NC5J by RARP, the RARP server which has been
properly set should be operating in the sub network.
Used to set an IP address of the AR-NC5J. The set value is in the
form of decimal number of "xxx.xxx.xxx.xxx."
Used to set the subnet mask of the AR-NC5J. The set value is in the
form of decimal number of "xxx.xxx.xxx.xxx." When "0.0.0.0" is set,
this item is disabled, and the subnet mask corresponding to the IP
address is automatically used.
Used to set an IP address of the gateway. The set value is in the form
of decimal number of "xxx.xxx.xxx.xxx." The gateway must exist in the
same sub network as the AR-NC5J. When "0.0.0.0" is set, this item is
disabled.
Used to set whether to output the banner page when printing with LPR
or FTP.
Descriptions
Used to disable/enable the NetWare protocol operation. This setup
will affect the operations of the print server, the remote printer, and the
setup utility (for IPX/SPX).
Used to set the default frame type which is used by the AR-NC5J. If
the set frame type does not work, another frame type is automatically
selected.
Used to set the priority operation mode (print server/remote printer) of
the AR-NC5J. If the set mode does not work, another mode is
automatically selected and tried.
Used to set the printer name which is registered in the print server
information in the NetWare server. This setup must be identical to the
setup of the printer name registered in the NetWare server.
Used to set the print server name when the AR-NC5J is booted in the
print server mode. Since this setup is used as an identification
element in a network with the NetWare protocol, it must be different
from the other NetWare product names. It is used as the login name to
log in the NetWare server.