Epson SC-S80600 Series User Manual
  1. Manuals
  2. Brands
  3. Epson Manuals
  4. Printer
  5. SC-S80600 Series
  6. User manual

Epson SC-S80600 Series User Manual

Hide thumbs Also See for SC-S80600 Series:
Table of Contents

Advertisement

Quick Links

Download this manual
User's Guide
CMP0207-00 EN

Advertisement

Table of Contents
loading

Related Manuals for Epson SC-S80600 Series

Summary of Contents for Epson SC-S80600 Series

  • Page 1 User's Guide CMP0207-00 EN...
  • Page 2 (excluding the U.S.) failure to strictly comply with Seiko Epson Corporation’s operating and maintenance instructions. Seiko Epson Corporation shall not be liable for any damages or problems arising from the use of any options or any consumable products other than those designated as Original Epson Products or Epson Approved Products by Seiko Epson Corporation.

  • Page 3: Table Of Contents

    Pre-installed software....26 Cleaning Locations and Cleaning Timing..60 Using Epson Edge Dashboard....27 Locations of Consumables and Replacement Starting Procedure.
  • Page 4 S80600L Series only)..... . . 89 Epson Edge Print..... . 136 Notes on Changing.
  • Page 5 SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Contents Help for Users in the Philippines... 146 Software License Terms Open Source Software Licenses....147 Bonjour.

  • Page 6: Introduction

    “Cleaning Around the Print Head” on page 67 Additional Print Drying System The heater can be used to rapidly dry ink after printing. This is an option for the SC-S80600 Series/SC-S80600L Series/SC-S40600 Series. U Additional Print Drying System Setup Guide After heater The heater can be used to rapidly dry ink after printing.
  • Page 7 SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Introduction Roll core holder Place the roll core for media take-up on these holders. There are same parts on both the left and the right. “Using the Auto Take-up Reel Unit” on page 36 Roll support Rest media temporarily on these supports when removing the take-up roll.
  • Page 8 SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Introduction Control panel “Control panel” on page 15 Air filter These filters absorb ink mist as air passes through the printer. The air filters are consumable items. Replace the wiper unit at the same time.

  • Page 9: Right View

    SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Introduction Right view The illustration shows the SC-S80600L Series. Airflow vents Allows air to flow into the printer. Do not obstruct these vents. Waste ink tube Tubes for ejecting waste ink. Be sure the end of this tube is in the Waste Ink Bottle while the printer is in use.

  • Page 10: Inside

    AC inlet #1/AC inlet #2/AC inlet #3 Connect the power cables supplied with the printer to #1 and #2. Be sure to connect both cables. Connect the power cable supplied with the ink unit to #3. #3 is not available for the SC-S80600 Series/SC-S60600 Series/SC-S40600 Series.
  • Page 11 “Daily Cleaning” on page 64 Caps Except during printing, these caps cover the print head nozzles to prevent them drying out. The SC-S80600 Series/ SC-S80600L Series/SC-S60600 Series/SC-S60600L Series have 2 blocks. Clean at least once a month. “Cleaning Around the Caps” on page 67 Wiper unit The wiper removes ink from the surface of the print head nozzles.

  • Page 12: Back

    SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Introduction Back Drive switch The drive switch is used to feed the media during loading and to rewind the media for replacement. Roll holder Place media on these holders. There are same parts on both the left and the right.

  • Page 13: Ink Unit (Sc-S80600L Series/Sc-S60600L Series)

    SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Introduction Ink unit (SC-S80600L Series/SC-S60600L Series) Ink Unit The ink unit supplies ink to the printer. Insert the ink supply units in all the trays. Security cable attachment Pass a commercially available security cable through the upper and lower mounting parts to prevent the ink supply units from being stolen.
  • Page 14 SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Introduction LED lamp The LED lamp indicates the status of the ink unit and the ink supply units inserted into their trays by lighting or flashing, as shown below. Lit blue : Ink is being supplied to the printer. Do not pull out the tray.

  • Page 15: Control Panel

    SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Introduction Pressing this button displays the Media Setup menu Control panel on the screen to perform Feed To Cut Position, Media Remaining, Select Media, Customize Settings, and Easy Media Setup. “The Media Setup Menu” on page 103 If you press this while printing, you can adjust the media feed.

  • Page 16: Understanding The Display

    SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Introduction ❏ Pressing this button displays the Maintenance menu When the media loading lever is lowered Press the d button to feed the media and the u button on the screen to perform Nozzle Check, Cleaning, to rewind it.
  • Page 17 SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Introduction : Ready to print. The height of the Heater temperature indicator changes with the level of ink From left to right, this display shows the settings for remaining in the cartridge/ink supply the pre-heater, platen heater, and after heater.
  • Page 18 SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Introduction : Metallic Silver Displays the settings for the Additional Print Drying System (optional for the SC-S80600 Series/ : Cleaning Cartridge/Cleaning Ink Supply SC-S80600L Series/SC-S40600 Series). Unit No icon : Not installed, or it is not installed correctly.

  • Page 19: Features

    SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Introduction Features High Print Quality Smooth Gradations, High-Fidelity Color This large-format color ink jet printer supports roll Reproduction media 1626 mm (64 inches) in width. The main features The SC-S80600 Series/SC-S80600L Series are equipped of this printer are described below.

  • Page 20: Notes On Usage And Storage

    (EMX) provided 100 Base-TX/1000 Base-T network interfaces. by Epson. An EMX is a print settings file for each media type and includes print information that is necessary to print correctly on commercially available media, such as...

  • Page 21: Notes When Using The Printer

    SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Introduction ❏ When the power is on, do not remove the power Notes when using the printer plug or cut the power at the breaker. The print head may not be capped properly. In this case, turn on the...

  • Page 22: Notes On Handling Ink Cartridges/Ink Supply

    SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Introduction ❏ The pressure rollers may crease media left in the ❏ 6 months from the day the ink cartridge printer. The media may also become wavy or packaging is opened, or 6 months from the day...

  • Page 23: Notes On Handling The Ink Unit (Sc-S80600L Series/Sc-S60600L Series)

    SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Introduction ❏ Although the ink cartridges/ink supply units may ❏ Do not touch the printable surface. Moisture and contain recycled materials, it does not affect the oils from your hands can affect print quality.
  • Page 24 SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Introduction Before using WH/MS inks, take note of the following “The Maintenance Menu” on page 110 cautions. Notes on auto ink circulation This function automatically circulates inks in the print head or tubes for WH/MS inks at periodic intervals to prevent ink sedimentation from occurring.

  • Page 25: Introducing The Supplied Software

    For information about the software, see the on-line help for the application or the Network Guide (Online Manual). Note: Printer drivers are not provided. A software RIP is required for printing. The Epson Software RIP, "Epson Edge Print", is included with this printer on a separate CD.

  • Page 26: Pre-Installed Software

    Introduction Software Name Summary Epson communications Epson communications drivers is required when using Epson Edge Dashboard, Epson Edge Print drivers and when connecting a computer to the printer via USB. Make sure these are installed. (Windows only) EpsonNet Config SE With this software, you can configure various network settings for the printer from your computer.

  • Page 27: Using Epson Edge Dashboard

    Software that is not displayed in the list cannot be updated using EPSON Software Updater. Check for the latest versions of the software from the Epson Web site. Close the Web browser. However, since Epson Edge Dashboard is a resident software, it does not stop https://www.epson.com...

  • Page 28: Receiving Update Notifications

    SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Introduction Uninstalling Software Receiving update notifications Start EPSON Software Updater. Important: ❏ Log into a "Computer administrator" account Click Auto update settings. (an account with administrative privileges). ❏ Enter the administrator password when...
  • Page 29 SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Introduction The following describes how to remove Epson Edge Dashboard. Quit Epson Edge Dashboard. Double-click Applications - Epson Software - Epson Edge Dashboard - Epson Edge Dashboard Uninstaller. Follow the on-screen instructions to continue.

  • Page 30: Basic Operations

    SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Basic Operations Notes on Loading Media Basic Operations Caution: Notes on loading media ❏ The heaters and media edge plate may be hot; observe all necessary precautions. Failure to observe the necessary precautions could result If the following points are not observed when handling in burns.
  • Page 31 SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Basic Operations Press the P button , and then wait until Load While holding the tabs of the media edge plate on media.is displayed on the screen. both sides, move the plate out of the way toward both edges of the platen.
  • Page 32 SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Basic Operations Move the roll holder to the set position according to the roll size of the media that will be loaded. Tighten the screw until the screw no longer turns. Firmly insert the roll core of the media onto the roll holder.
  • Page 33 SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Basic Operations To ensure the roll holder is inserted into the roll core sufficiently, push it twice. Important: If the roll holder is inserted into the roll core insufficiently, media is not fed correctly during printing because of slippage between the roll holder and roll core.
  • Page 34 SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Basic Operations Insert the media approximately 30 cm into the Important: opening, then lower the media loading lever. ❏ If the roll holder screw is loose, the roll holder may move during printing. This could cause stripes and unevenness in the print results.
  • Page 35 SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Basic Operations Note: If the left edge of the media is not within the black square of the label, do steps 5 to 16 in reverse to adjust the position of the roll holder. Do not attempt to reposition the roll holders while they are inserted in the media.

  • Page 36: Using The Auto Take-Up Reel Unit

    SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Basic Operations While holding the tabs of the media edge plate on both sides, move the plate to the top edge edge of the media. Adjust so that the edges of the media are aligned with the center of the round holes in the media edge plates.

  • Page 37: Attaching The Roll Core

    SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Basic Operations Loading Caution: ❏ Follow the instructions in the manual when Keep the d button pressed until the leading edge loading media or roll cores or removing media of the media reaches the center of the after heater.
  • Page 38 SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Basic Operations Align the roll core holder with the right edge of Leave a 10 to 20 cm wide section in the center of the media, and tighten the screw. the media, and cut at least 25 cm in height from the left and right corners of the media.

  • Page 39: Take-Up With The Printed Side Facing Out

    SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Basic Operations Flip the Auto switch to Take-up with the Printed Side Facing Out Cut the paper tape approximately 70 cm in length, and paste it approximately in the center of the media using commercially available adhesive tape.
  • Page 40 SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Basic Operations Flip the Auto switch to Off, and hold down the When there is no paper tape Manual switch to to wrap the media once While pulling the center section of the media around the roll core.

  • Page 41: Take-Up With The Printed Side Facing In

    SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Basic Operations Lower the tension bar until it slightly touches the Continue holding down the d button until the media. media has wrapped around once or twice. Confirm that the media is attached without looseness.
  • Page 42 SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Basic Operations While pulling the paper tape straight down, wrap Lower the tension bar until it slightly touches the it around the roll core from back to front, and paper tape. affix it using commercially available adhesive tape.
  • Page 43 SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Basic Operations Press the d button in the control panel to feed Flip the Auto switch to enough media for a single wrap around the roll core. Flip the Auto switch to Off, and hold down the...

  • Page 44: Settings For Loaded Media

    SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Basic Operations 2. Select the roll winding specifications Note: Select the roll type for the loaded media roll. You can confirm differences in tension by lightly tapping both edges of the media as shown in the illustration below.

  • Page 45: Saving New Media Settings

    SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Basic Operations Use the d/u buttons to select the roll type that The printer will display Ready after a brief pause, matches the loaded roll, and then press the Z showing that it is ready to print. Transmit the data to be button.

  • Page 46: Easy Media Setup Procedure

    SC-S60600 Series/ SC-S60600L Series the printer's setup menu *1 In one head mode for 10 color mode in SC-S80600 Series/ This is suitable for quick printing. If you select the media SC-S80600L Series when MS installed, approximately 80 mm type that you loaded, it saves the general-use media...
  • Page 47 SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Basic Operations Use the d or u button to select Easy Media Check the printed adjustment pattern. Setup, and then press the Z button. When anything except for Textile is selected Two groups of adjustment patterns, A and B, are Use the d/u buttons to select the desired media printed.

  • Page 48: Optimization Of Media Settings (Media Adjust)

    SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Basic Operations The screen for entering check results for the Select the finest lined pattern (all lines overlap) adjustment pattern is displayed. for both. Select "-1" in the cases shown below. When anything except Textile is selected...

  • Page 49: Notes On Media Adjust

    Do Feed Adjustment and Head Alignment separately Unit during Media Adjust, too. for any media selected, other than Adhesive Vinyl or ❏ If the media setting values are registered in Epson Banner, in Media Type. Visually check and adjust each printed pattern.
  • Page 50 SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Basic Operations If there are patterns where the overlapping or The approximate maximum length of the media gaps are the same, enter the middle value in step required to print the test pattern is given below.

  • Page 51: Removing The Take-Up Roll

    Series/SC-S80600L Series when MS installed, 12 Series blocks for A to L. *1 In one head mode for 10 color mode in SC-S80600 Series/ SC-S80600L Series when MS installed, approximately 80 mm Select the finest lined pattern (all lines overlap) *2 In two head mode for 10 color mode in SC-S80600 Series/ for both.

  • Page 52: Printing The Amount Of Media Remaining

    SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Basic Operations Select Print Remaining Length and press the 1. Print the remaining amount of media. (When Z button. Media Remaining is set to ON) Press the Z button to print the amount of media remaining.

  • Page 53: Removing Media

    SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Basic Operations When using the Auto Take-up Reel Unit, raise Set the Auto switch to Off. Take up the cut media the tension bar. completely by operating the Manual switch according to how the media is rolled.

  • Page 54: Before Printing

    SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Basic Operations Check the amount of ink remaining: Lower the roll onto the roll support. If ink is expended while printing, printing can be resumed once the affected ink cartridge/ink supply unit has been replaced.

  • Page 55: Changing Settings During Printing

    SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Basic Operations Changing settings during Correcting Banding printing When you want to correct banding during printing, perform Feed Adjustment. Changing the Heater Buttons that are used in the following settings Temperature and Drying...

  • Page 56: Checking Details For The Remaining Amount Of Ink And Wiper Units

    SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Basic Operations Press the Z button to display the status display Press the Menu button during printing. screen. The settings menu will be displayed. Note: Use the d/u buttons to select Printer Status, and If the setting is changed, the icon is displayed on the then press the Z button.

  • Page 57: Printable Area

    SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Basic Operations Printable area The left and right edges of media recognized by the printer varies as shown below according to the Media Size Check settings. Media Size Check ON : The printer automatically detects the left and right edges of the loaded media.
  • Page 58 SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Basic Operations The gray area in the illustration below shows the printable area. The arrow indicates the feed direction. * When Media Size Check is set to OFF, this is 1,626 mm (64 inches) regardless of the width of the loaded media.
  • Page 59 SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Basic Operations This may be available in the RIP depending on the RIP software being used. Contact the RIP manufacturer for more information. Note the following points when setting margins. ❏ Leave margins of 10 mm or more when using media edge plates. Narrower margins could result in printer printing over the plates.

  • Page 60: Maintenance

    SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Maintenance Maintenance When to Perform Various Maintenance Operations Cleaning Locations and Cleaning Timing If you continue to use the printer without cleaning, it could cause clogged nozzles or ink drops to occur.

  • Page 61: Locations Of Consumables And Replacement Timing

    SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Maintenance Locations of Consumables and Replacement Timing When to perform Component to be replaced When a prepare and replacement Air filters message is displayed on the control panel Flushing pad screen Wiper unit “Replacing Maintenance Parts”...
  • Page 62 “Cleaning inside the front cover” on page 90 When a greasing message is displayed on Applying the supplied grease to the carriage rod the control panel “Applying Grease to the Carriage Rod” on page 91 * When 10 color mode is selected on SC-S80600 Series/SC-S80600L Series.

  • Page 63: What You'll Need

    SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Maintenance Use when putting cleaning utensils, removed What You’ll Need consumables, or ink cleaner moved in the container supplied with the printer. Ready the following items before beginning cleaning and replacement. Important: If the used cleaning stick, etc.

  • Page 64: Daily Cleaning

    SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Maintenance ❏ Do not use water or alcohol to clean around the Caution: print head or the caps and so on. Ink congeals when ❏ Store ink cartridges, ink supply units, cleaning mixed with water or alcohol.

  • Page 65: Performing Regular Cleaning

    SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Maintenance Soak a soft cloth in water, wring it out Performing Regular thoroughly, and then wipe off any ink, lint, or dust that has adhered to the platen heater. Cleaning Carefully remove lint and dust stuck in the groove of the platen.

  • Page 66: Moving The Print Head

    SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Maintenance Dampen the cleaning stick with ink cleaner. Buttons that are used in the following settings Do not allow ink cleaner to drip from the cleaning stick. When dampening a clean-room wiper with ink cleaner, use ink cleaner poured into a cup.

  • Page 67: Cleaning Around The Print Head

    SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Maintenance Wipe off any adhered ink, lint, and dust from the Cleaning Around the Print Head parts that are indicated by the arrows below. If you notice any ink clots, lint, or dust when checking the area around the print head, clean the area by following the steps below.
  • Page 68 SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Maintenance “Precautions regarding maintenance” on page 63 Important: Do not push strongly against the edges or the Cleaning Caps surrounding area of the cap, or touch the inner side of the cap with a cleaning stick or tweezers.
  • Page 69 SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Maintenance When ink adheres to the guide section Hold the cleaning stick in a perpendicular orientation, and wipe the outer areas of all the caps. Dampen the cleaning stick with ink cleaner.

  • Page 70: Flushing Pad

    SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Maintenance When a film of ink adheres to the When there is lint or dust in the cap guide section Remove using the tip of the cleaning stick or tweezers. If a film-like layer of adhered ink cannot be removed completely using a cleaning stick, remove it using tweezers.

  • Page 71: Finishing Cleaning

    SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Maintenance Shaking and Replacing Ink Cartridges (SC-S80600 Series/SC-S60600 Series/ SC-S40600 Series) Shaking Timing and frequency of shaking Important: If no other parts need to be cleaned, proceed to the Due to ink characteristics, the ink cartridges of this following section.

  • Page 72: Replacement Procedure

    SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Maintenance ❏ Once every three weeks (All colors excluding WH/ If you continue to use ink cartridges that are running low, you may need to replace the ink cartridge while Even after installing an ink cartridge in the printer, printing.
  • Page 73 SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Maintenance Insert a finger into the depression on the top of Lower the lock lever to engage the latch. the cartridge and pull the cartridge straight toward you. Repeat Steps 2 to 6 to replace other ink cartridges.

  • Page 74: Shaking And Replacing Ink Supply Units (Sc-S80600L Series/Sc-S60600L Series)

    SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Maintenance Shaking method Shaking and Replacing Ink Supply Units Make sure the printer is on, and then pull the tray that needs to be shaken out of the ink unit. (SC-S80600L Series/ Any ink supply unit whose LED lamp is flashing blue needs to be shaken.

  • Page 75: Replacement Procedure

    SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Maintenance Pull the tray of the ink supply unit you want to Replacement procedure replace out of the ink unit. If one of the installed ink supply units is expended, printing cannot be performed.

  • Page 76: Disposing Of Waste Ink

    SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Maintenance Place the new ink supply unit into the tray and Move the lock switch to the left to lock it. lower the handle. Repeat steps 2 to 7 to replace other ink supply units.

  • Page 77: Waste Ink Counter

    SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Maintenance “Precautions regarding maintenance” on page 63 Important: During printing or while the printer is running the Remove the Waste Ink Bottle from the Waste Ink Bottle holder. operations shown below, do not remove the Waste...

  • Page 78: Replacing Maintenance Parts

    SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Maintenance SC-S80600L Series/SC-S60600L Series Check again to confirm that a fresh Waste Ink Bottle is correctly placed and then press the Zbutton to reset the waste ink counter. Important: Be sure to confirm that the waste ink tube is inserted in the mouth of the waste ink bottle.

  • Page 79: Replacing Maintenance Parts

    SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Maintenance Maintenance menu U “The Maintenance Menu” on Replacing Maintenance Parts page 110 When the message is displayed, press the Z Important: button. Maintenance Counter After the print head moves to the left end of the The printer tracks amounts consumed using the printer, open the right maintenance cover.
  • Page 80 SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Maintenance To avoid soiling your surroundings with ink, Lift up the tab on the flushing pad, and remove wrap the used wiper unit in the packaging supplied with the new wiper unit.

  • Page 81: Replacing The Media Edge Plates

    SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Maintenance Insert the two hooks on the flushing pad into the Check that the air filters are installed, and then slots on the printer and press the tab down until press the Z button.
  • Page 82 SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Maintenance If the additional print drying system is installed, make sure you unplug the power cable for the additional print drying system as well. Leave the printer for a minute, and then open the left maintenance cover and the front cover.
  • Page 83 SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Maintenance Check that three hooked sections at the rear of the media edge plate are securely applied as shown below and that they are attached with no gap between the platen and media edge plate.

  • Page 84: Disposal Of Used Consumables

    In such cases, submit the “Safety Releasing the tab fixes the media edge plate. data sheet” to the industrial waste disposal company. You can download it at your local Epson Web site. Checking for clogged nozzles We recommend that you check the nozzles for clogs each time you print to ensure quality results.

  • Page 85: Printing Nozzle Check Patterns

    SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Maintenance When printing for the set number of pages is complete, Printing nozzle check patterns the printed check pattern is read by the sensor to confirm that there is no clogging. Buttons that are used in the following settings If no clogging is detected, printing continues.

  • Page 86: Head Cleaning

    SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Maintenance cleared even after performing this operation twice, Important: a message asking if you want to continue printing is displayed. Always remove clogs from the nozzles of all “The Printer Setup Menu” on page 107 colors before resuming use.

  • Page 87: Long-Term Storage (Pre-Storage Maintenance)

    SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Maintenance (1) Perform Auto Head Maintenance from the setup All Nozzles Choose this option if all patterns in the printed menu. nozzle check results contain faint or missing segments. After making your selections, proceed “The Maintenance Menu”...

  • Page 88: Performing Pre-Storage Maintenance

    SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Maintenance Performing Pre-storage Interval Number of CLs Maintenance 1 month or more SC-S40600 Series: 4 SC-S60600 Series: 8 SC-S60600L Series: 8 Important: If the amount of remaining ink or cleaning fluid is insufficient, the function may not run.

  • Page 89: Restarting Use Of The Printer

    SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Maintenance Time required: up to approximately 1 hour The time required to complete the change varies Observe the following cautions when storing the printer according to the current color mode. and ink cartridges/ink supply units that were removed during use.

  • Page 90: Change Color Mode Procedure

    SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Maintenance When the printer is not used for approximately three Then follow the on-screen instructions to replace the months or more. ink cartridge/ink supply unit. * The standard period is indicated, assuming the Observe the following cautions when storing the ink following usage conditions.

  • Page 91: Cleaning Pressure Rollers

    SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Maintenance Cleaning pressure rollers Important: When wiping, make sure the cloth or your finger does not touch the rod B shown in the If you keep using the pressure rollers when they are illustration.

  • Page 92: Greasing Procedure For Carriage Rod A

    SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Maintenance Carriage rod A Use the u button to select Grease Carriage Rod, and then press the Z button. When Grease kit is needed. Continue? is displayed. Make sure that you have a grease kit ready to use.
  • Page 93 SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Maintenance Important: Do not slide the tool back and forth. If you slide the tool back and forth, dust will be moved to the print head stand-by position and a malfunction may occur.

  • Page 94: Greasing Procedure For Carriage Rod B

    SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Maintenance Greasing procedure for carriage rod B Hold a new pad B firmly against the gray part of the rod as shown in the illustration, and smoothly slide it from the right end to the left end to wipe off stains on the rod.
  • Page 95 SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Maintenance ❏ Store the container at room temperature with the cap uppermost in a location that is not exposed to direct sunlight.

  • Page 96: Using The Control Panel Menu

    SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Using the Control Panel Menu Using the Control Panel Menu Menu Operations The menus are used as shown below. Ready Menu Media Setup Media Remaining Remaining Setup Media Setup Feed To Cut Position...

  • Page 97: Menu List

    SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Using the Control Panel Menu Menu List The following items and parameters can be set and executed in the Menu. See the reference pages for more details on each item. Media Setup For more information on these items, see U “The Media Setup Menu”...
  • Page 98 SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Using the Control Panel Menu Item Parameter Current Settings 1 to 30 (media setting number) Setting Name Up to 22 half-size characters Media Type Adhesive Vinyl, Banner, Film, Canvas, Textile, Paper/Other Media Adjust...
  • Page 99 SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Using the Control Panel Menu Item Parameter Head Movement Data Width, Printer Full Width Multi Strike Printing OFF, 2 to 8 Feed Speed Limiter ON, OFF Pressure Roller Load Low, Medium, Heavy...
  • Page 100 “The Maintenance Menu” on page 110 Setting items and setting values marked with asterisks indicate the following printer models. *1: for SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series only, *2: for SC-S80600 Series/ SC-S80600L Series only, *3: for SC-S60600 Series/SC-S60600L Series only...
  • Page 101 SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Using the Control Panel Menu Item Parameter Execute Ink Circulation Execute Ink Refresh Head Washing XX/XX, Head1 XX/XX , Head2 XX/XX , Head1 All Nozzles Head2 All Nozzles , All Nozzles ("XX" indicates an ink color code.) Pre-Storage Maint.
  • Page 102 SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Using the Control Panel Menu Item Parameter Date And Time MM/DD/YY HH:MM Language Japanese, English, French, Italian, German, Portuguese, Spanish, Dutch, Russian, Korean, Chinese Units Unit: Length m, ft/in Unit: Temperature ˚C, F...

  • Page 103: Details Of The Menu

    SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Using the Control Panel Menu Details of the Menu The Media Setup Menu The Media Setup menu can be accessed directly by pressing the M button. * indicates default settings. Feed To Cut Position Sends the end of the print to the cutting groove.
  • Page 104 SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Using the Control Panel Menu *1: For the SC-S80600L Series/SC-S60600L Series only Item Parameter Explanation Setting Name Assign the media setting bank a name up to 22 half-size characters long. Using distinctive names makes it easier to select banks for use.
  • Page 105 SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Using the Control Panel Menu Item Parameter Explanation Platen Gap Choose the platen gap (the distance between the print head and the media). The default setting of 1.6 is recommended in most situations. Choose 2.0 if the printout is scratched or smudged.
  • Page 106 SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Using the Control Panel Menu Item Parameter Explanation Media Tension Increase tension if creases appear in the media during printing. The higher the value, the greater the tension. Media Suction When media is waved on the platen, increase the Media Suction. The 0 to 10 (4 higher the value, the greater the suction.

  • Page 107: The Printer Setup Menu

    SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Using the Control Panel Menu Item Parameter Explanation Length Sets the frequency for periodic cleaning according to the prints performed. Enter Value 1 to 100 (10 Enter Value performs head cleaning after printing a specific number of meters.
  • Page 108 SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Using the Control Panel Menu Item Parameter Explanation Side Margin(Right) Choose the width of the right margin when media is loaded in the printer. 3 to 25 mm (5 See the following for more information.
  • Page 109 Auto Nozzle Check is not available under the following conditions: ❏ Areas that print using WH/MS inks in SC-S80600 Series/SC-S80600L Series (10 color mode). (This can still be performed with other colors.) ❏...

  • Page 110: The Maintenance Menu

    The Maintenance menu can be accessed directly by pressing the # button. Setting items and setting values marked with asterisks (*X) indicate the following. *1: for SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series only, *2: for SC-S80600 Series/ SC-S80600L Series only, *3: for SC-S60600 Series/SC-S60600L Series only...
  • Page 111 SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Using the Control Panel Menu Item Parameter Explanation Head Maintenance Auto Head If the message Press # and perform Head Maintenance. is displayed on Maintenance the control panel screen, select Regular Cleaning and perform cleaning.
  • Page 112 All Nozzles: Select this when faint or missing segments of all colors are detected. You can also select the following for the SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series. Head1 XX/XX/Head2 XX/XX: Select the target color for a target head when faint or missing segments of a specific color are detected.

  • Page 113: The Printer Status Menu

    SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Using the Control Panel Menu The Printer Status Menu These items track printer use and settings. Setting items and setting values marked with asterisks (*1) indicate the following printer models. *1: For SC-S80600 Series/SC-S60600 Series/SC-S40600 Series only...
  • Page 114 SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Using the Control Panel Menu Item Parameter Explanation Date And Time MM/DD/YY HH:MM Set the printer’s built-in clock. The time provided by the clock is used when printing logs and status sheets.

  • Page 115: Problem Solver

    SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Problem Solver Problem Solver When a Message is Displayed If one of the following messages is displayed, read and follow the instructions below. Messages What to do Prepare empty waste ink bottle.
  • Page 116 Use Epson Edge Dashboard to update the firmware again. Restart the printer. If this message appears in the control panel again, contact your dealer or Epson Support. * Version 1.5 or earlier is called the Epson Control Dashboard Print head is nearing end of service life.

  • Page 117: When A Maintenance Call/Service Call Occurs

    Maintenance Request A part used in the printer is nearing the end of its service life. Replace Part Now/Replace Part Soon Contact your dealer or Epson Support and tell them the maintenance request XXXXXXXX code. You cannot clear the maintenance request until the part is replaced. A service call occurs if you continue to use the printer.

  • Page 118: Troubleshooting

    SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Problem Solver You cannot print under the network Troubleshooting environment. You cannot print (because the Are the network settings correct? Ask your network administrator for the network printer does not work) settings.

  • Page 119: The Prints Are Not What You Expected

    SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Problem Solver Test pattern does not print correctly. Are you using the recommended genuine Epson ink cartridge/ink supply unit? This printer is developed for use with Epson ink Perform head cleaning. cartridges/ink supply units. If you use non-Epson ink The nozzles may be clogged.

  • Page 120: Media

    SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Problem Solver Vertical ruled lines are misaligned. Shake the WH/MS ink cartridge or the WH/MS ink supply unit. When using SC-S80600 Series/SC-S80600L Series as Is the media wavy? 10 color mode, sedimentation may occur in the WH/...
  • Page 121 SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Problem Solver Removing Jammed Media. If the print head is over the media, move it away from the jam. Follow the steps below to remove jammed media. Caution: Be careful not to trap your hands or fingers when opening or closing the front cover.

  • Page 122: Others

    SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Problem Solver The control panel display keeps Turn the printer on. turning off. Important: If the printer is left off for an extended period, Is the printer in sleep mode? the print head will be left uncapped and dry...

  • Page 123: Appendix

    Epson recommends the use of genuine Epson ink cartridges/Ink Supply Unit. Epson cannot guarantee the quality or reliability of nongenuine ink. The use of non-genuine ink may cause damage that is not covered by Epson's warranties, and under certain circumstances, may cause erratic printer behavior.
  • Page 124 SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Appendix Printer model Product Part number SC-S80600 Ink cartridges Black T8331 (Australia and New Cyan T8332 Zealand) Magenta T8333 Yellow T8334 Light Cyan T8335 Light Magenta T8336 Light Black T8337 Orange T8338...
  • Page 125 SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Appendix Printer model Product Part number SC-S80670 Ink cartridges Black T8921 Cyan T8922 Magenta T8923 Yellow T8924 Light Cyan T8925 Light Magenta T8926 Light Black T8927 Orange T8928 T8929 White T892A Metallic Silver...

  • Page 126: Ink Supply Unit

    SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Appendix Printer model Product Part number SC-S40610 Ink cartridges Black T8911 SC-S60610 Cyan T8912 Magenta T8913 Yellow T8914 SC-S40670 Ink cartridges Black T8921 SC-S60670 Cyan T8922 Magenta T8923 Yellow T8924 SC-S40680 Ink cartridges...
  • Page 127 SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Appendix Printer model Product Part number SC-S80610L Ink Supply Unit Black T45N1 Cyan T45N2 Magenta T45N3 Yellow T45N4 Light Cyan T45N5 Light Magenta T45N6 Light Black T45N7 Orange T45N8 T45N9 White T45NA...
  • Page 128 SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Appendix Printer model Product Part number SC-S80670L Ink Supply Unit Black T45P1 Cyan T45P2 Magenta T45P3 Yellow T45P4 Light Cyan T45P5 Light Magenta T45P6 Light Black T45P7 Orange T45P8 T45P9 White T45PA...

  • Page 129: Maintenance Items

    SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Appendix Printer model Product Part number SC-S60660L Ink Supply Unit Black T45M1 Cyan T45M2 Magenta T45M3 Yellow T45M4 SC-S60670L Ink Supply Unit Black T45P1 Cyan T45P2 Magenta T45P3 Yellow T45P4 SC-S60680L Ink Supply Unit...
  • Page 130 SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Appendix For SC-S80600L Series/SC-S60600L Series Product Part number Explanation Cleaning Ink Supply Unit T44A5 Use when performing Pre-Storage Maint.. (except for SC-S80660L/ SC-S60660L) Cleaning Ink Supply Unit T44A6 (for SC-S80660L/SC-S60660L) Maintenance Parts Kit...

  • Page 131: Pantone Color Explanation

    SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Appendix PANTONE Color Cut media Explanation Media width 300 to 1626 mm (64 inch) Media length 500 mm or more There are many variables in process reproduction of Media thickness Up to 1 mm...

  • Page 132: Moving And Transporting The Printer

    SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Appendix Disconnect the power cords and all other cables. Moving and Transporting If you are using the SC-S80600L Series/ the Printer SC-S60600L Series, remove the following from the ink unit. ❏ Power cable and connection cable This section describes how to move and transport the product.

  • Page 133: Transport

    SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Appendix If you do not have the Setup Guide on hand, select Important: and refer to the model of your printer from https://epson.sn. When performing level adjustment using the adjusters, make sure you raise the adjusters Plug in the power cables and turn the printer on.

  • Page 134: Media Settings List For Each Media Type

    Feed Speed Limiter Pressure Roller Load Heavy Medium Medium Medium Heavy Remove Skew Periodical Cleaning Auto Auto Auto Auto Auto Auto * For the SC-S60600 Series/SC-S60600L Series or the SC-S80600 Series/SC-S80600L Series/SC-S40600 Series with the optional additional print drying system installed.

  • Page 135: System Requirements

    For the latest information, see the Epson Web site. Epson Edge Dashboard Important: Make sure the computer on which the Epson Edge Dashboard is installed meets the following requirements. If these requirements are not met, the software cannot monitor the printer correctly. ❏ Disable your computer's hibernate function.

  • Page 136: Epson Edge Print

    SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Appendix Communication interface High Speed USB Ethernet 1000Base-T Browser Safari 6 or later Linux Distribution Debian 8.6 64bit (MATE desktop environment only) or later Multi-core processor (3.0 GHz or better recommended) Free memory...
  • Page 137 SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Appendix Internet Explorer 11, Microsoft Edge, Firefox, Chrome, Safari...

  • Page 138: Specifications Table

    SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Appendix Specifications Table Printer Specifications Rated current (#1, #2) 10A (100 to 120V AC) 5A (200 to 240V AC) Printer Specifications Rated current (external 1A (100 to 120V AC) Printing method On-demand ink jet drying fan units 0.5A (200 to 240V AC)
  • Page 139 SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Appendix Printer Specifications Printer Specifications Humidity Operating: 20 to 80% (40 to 60% SC-S80600 Series: Approx. Weight recommended) (without 284 kg condensation) SC-S80600L Series: Approx. Storage: 5 to 85% (without 328 kg condensation) SC-S60600 Series: Approx.
  • Page 140 SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Appendix Important: Ink Specifications ❏ Do not refill the the ink cartridge with ink. Type Dedicated ink cartridges/ink supply ❏ Use the printer at an altitude of 2000 m or less. units...

  • Page 141: Where To Get Help

    Support Technical Support Web Before Contacting Epson Site If your Epson product is not operating properly and you cannot solve the problem using the troubleshooting Epson's Technical Support Web Site provides help with information in your product documentation, contact problems that cannot be solved using the Epson support services for assistance.

  • Page 142: Help For Users In North America

    SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Where To Get Help Help for Users in North America Help for Users in Taiwan Epson provides the technical support services listed Contacts for information, support, and services are: below. World Wide Web...

  • Page 143: Help For Users In Australia/New Zealand

    04-23805000 04-23806000 No.530, Sec. 4, Henan Epson Helpdesk Rd., Nantun Dist., Taichung City 408, Epson Helpdesk is provided as a final backup to make Taiwan sure our clients have access to advice. Operators on the 05-2784222 05-2784555 No.463, Zhongxiao Rd., Helpdesk can aid you in installing, configuring and East Dist., Chiayi City...

  • Page 144: Help For Users In Thailand

    SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Where To Get Help Epson HelpDesk World Wide Web (Phone: (65) 6586 3111) (https://www.epson.co.id) Our HelpDesk team can help you with the following ❏ Information on product specifications, drivers for over the phone: download ❏...

  • Page 145: Help For Users In Hong Kong

    603-56288222 Internet Home Page ❏ Enquiries on repair services & warranty, product usage and technical support (Techline) Epson Hong Kong has established a local home page in both Chinese and English on the Internet to provide Phone: 603-56288333 users with the following information: ❏...

  • Page 146: Help For Users In The Philippines

    SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Where To Get Help ❏ Enquiries on repair service and warranty Location Telephone Fax number number Cochin 0484-2357950 0484-2357950 Coimbatore 0422-2380002 Pune 020-30286000 / 020-30286000 30286001 /30286002 Ahmedabad 079-26407176 / 77 079-26407347...

  • Page 147: Software License Terms

    SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Software License Terms Software License Terms Open Source Software Licenses Bonjour This printer product includes the open source software programs which apply the Apple Public Source License Version1.2 or its latest version ("Bonjour Programs").
  • Page 148 SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Software License Terms 1.6 "Modifications" mean any addition to, deletion from, and/or change to, the substance and/or structure of the Original Code, any previous Modifications, the combination of Original Code and any previous Modifications, and/ or any respective portions thereof.
  • Page 149 SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Software License Terms 2.3 Distribution of Executable Versions. In addition, if You Externally Deploy Covered Code (Original Code and/or Modifications) in object code, executable form only, You must include a prominent notice, in the code itself as well as in related documentation, stating that Source Code of the Covered Code is available under the terms of this License with information on how and where to obtain such Source Code.
  • Page 150 SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Software License Terms 8. NO WARRANTY OR SUPPORT. The Covered Code may contain in whole or in part pre-release, untested, or not fully tested works. The Covered Code may contain errors that could cause failures or loss of data, and may be incomplete or contain inaccuracies.
  • Page 151 SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Software License Terms (c) automatically without notice from Apple if You, at any time during the term of this License, commence an action for patent infringement against Apple; provided that Apple did not first commence an action for patent infringement against You in that instance.

  • Page 152: Openssl License/Original Ssleay License

    SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Software License Terms EXHIBIT A. "Portions Copyright (c) 1999-2003 Apple Computer, Inc. All Rights Reserved. This file contains Original Code and/or Modifications of Original Code as defined in and that are subject to the Apple Public Source License Version 2.0 (the 'License').
  • Page 153 SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Software License Terms notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. * 3. All advertising materials mentioning features or use of this software must display the following acknowledgment: "This product includes software developed by the OpenSSL Project...
  • Page 154 SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Software License Terms * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,...
  • Page 155 SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Software License Terms * included with this distribution is covered by the same copyright terms * except that the holder is Tim Hudson (tjh@cryptsoft.com). * Copyright remains Eric Young's, and as such any Copyright notices in * the code are not to be removed.

  • Page 156: Other Software Licenses

    SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Software License Terms * THIS SOFTWARE IS PROVIDED BY ERIC YOUNG ``AS IS'' AND * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE * ARE DISCLAIMED.
  • Page 157 SC-S80600 Series/SC-S80600L Series/SC-S60600 Series/SC-S60600L Series/SC-S40600 Series User's Guide Software License Terms This software is provided "as is," without warranty of any kind, express or implied. In no event shall Info-ZIP or its contributors be held liable for any direct, indirect, incidental, special or consequential damages arising out of the use of or inability to use this software.

This manual is also suitable for:

Sc-s80600l seriesSc-s60600 seriesSc-s60600l seriesSc-s40600 series

Table of Contents