Hussmann ESC Installation And Operation Manual
  1. Manuals
  2. Brands
  3. Hussmann Manuals
  4. Merchandiser
  5. ESC
  6. Installation and operation manual
Hussmann ESC Installation And Operation Manual

Hussmann ESC Installation And Operation Manual

Deli/meat/fish service case
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
ESC
DELI/MEAT/FISH SERVICE CASE
P/N IGSV-ESC-0303
INSTALLATION & OPERATION GUIDE

Advertisement

Table of Contents
loading

Related Manuals for Hussmann ESC

Summary of Contents for Hussmann ESC

  • Page 1 DELI/MEAT/FISH SERVICE CASE P/N IGSV-ESC-0303 INSTALLATION & OPERATION GUIDE...

  • Page 2: Table Of Contents

    Check your shipment for any possible shortages of material. If a shortage should exist and is found to be the responsibility of Hussmann Chino, notify Hussmann Chino. If such a shortage involves the carrier, notify the carrier immediately and request an inspection.

  • Page 3: Important Information

    Rev. 0303 The ESC service cases are easy to work, attractive merchandising display cases capable of maintaining superb product quality, with the installation of the proper controlling devices. These should be set according to the manufacturer’s specifications and combined with a properly maintained humidity system.

  • Page 4: Cut & Plan Views

    1" FRONT FRONT 30° OUTSIDE WEDGE FRONT FRONT 45° OUTSIDE WEDGE 4' - 11 " " FRONT FRONT 90° 90° OUTSIDE WEDGE IGSV-ESC-0303 Light " Optional St. Steel Slanted Deck Pan (Meat/Fish) 36" Water PEDESTAL Raceway OPTION " " 26"...

  • Page 5: Installation

    Rev. 0303 LOCATION The refrigerated merchandisers have been designed for use only in air conditioned stores where temperature and humidity are maintained at or below 75°F and 55% rela- tive humidity. DO NOT allow air conditioning, electric fans, ovens, open doors or windows (etc.) to create air cur- rents around the merchandiser, as this will impair its cor- rect operation.
  • Page 6 11.Use finger to smooth butyl as thin as possible at masking tape on inside and outside of rear mullion IGSV-ESC-0303 health codes. A,B,D A,B,D A,C,D,E...
  • Page 7 Rev. 0303 (apply additional butyl if necessary). Remove tape applied on line #3. INSIDE REFRIGERATED WEDGES Line up taper pins with holes on adjoining case. Turn cam- lock to lock in. Two camlocks are located at the rear of the case behind the air discharge and behind the lower electrical raceway access panel.

  • Page 8: Glass Adjustment

    ESC Glass Adjustment NOTE: Before making any of the recommended adjustments, Verify that the case(s) have been leveled properly. Adjust glass Up and Down 1. Remove (vertically) rear prep ledge. Adjust glass Front to Back 1. Remove rear prep ledge and...

  • Page 9: Plumbing

    Rev. 0303 WASTE OUTLET AND P-TRAP The waste outlet is located off the center of the case on one side allowing drip piping to be run lengthwise under the fixture. A 1-1/2" P-trap and threaded adapter are supplied with each fixture. The P-trap must be installed to prevent air leakage and insect entrance into the fixture.

  • Page 10: Humidity System

    “L”, then removing it from the case, and flush- ing with a hose. **IMPORTANT INFORMATION** The ESC is capable of maintaining superb product qual- ity with the installation of the proper controlling de- vices. These devices should be set according to the manufacturer’s specifications.
  • Page 11 Rev. 0303 HUMIDIFICATION SYSTEM HOOKUPS Remove the raceway panel on the lower back of the case. The pre-piped water shut-off valve and the water filter are located on the left hand side of the case. The water line (which is a 1/4" OD copper fitting) can be connected to the ball shut-off valve, by means of a compression fit- ting (supplied).

  • Page 12: Refrigeration

    No. 2 from the temperature measured in step No. 3. 3. The difference is superheat. 5. Set the superheat for 5°F - 7°F. T-STAT LOCATION T-Stats are located within the electrical raceway. Refer to diagram below. Standard Location Optional Location IGSV-ESC-0303 Optional Location...

  • Page 13: Electrical

    Rev. 0303 WIRING COLOR CODE S TA N DA R D C A S E W I R E C O L O R C O D E GREEN GROUND PURPLE ANTI-SWEAT ORANGE LIGHTS YELLOW RECEPTACLE T-STAT 230V BROWN FAN MOTORS BLACK/WHITE T-STAT 115V BROWN...

  • Page 14: Finishing Touches

    After cases have been leveled and joined, and refrigera- tion, electrical, and wasted piping work completed, install the splashguards. Fasten along the top edge, or center, with #10 X 3/3" sheet metal screws. BULKHEAD JOINT CAP ESC EXT. BACKER FRONT CLOSEOFF OINT BUMPER INSTALLATION TIPS 1.

  • Page 15: User Information

    Hussmann cases were not designed to “heat up” or “cool down” product—but rather to maintain an item’s proper temperature for maximum shelf life. To achieve the pro- tection required always: 1.
  • Page 16 (this will corrode the copper components of the case) TO PRESERVE THE ATTRACTIVE FINISH: • DO USE WATER AND A MILD DETERGENT FOR THE EXTERIOR ONLY • DO NOT USE ABRASIVES OR STEEL WOOL SCOURING PADS (these will mar the finish) User Information, cont’d IGSV-ESC-0303...

  • Page 17: Lift Up Glass

    Rev. 0303 Installer Instructions READ BEFORE RAISING FRONT GLASS ON ESHS: IMPORTANT! READ BEFORE RAISING FRONT GLASS : HEX SCREWS ALONG CLAMSHELL MAY HAVE LOOSENED DURING SHIPPING!! RETIGHTEN ALL CLAMSHELL SCREWS BEFORE OPENING GLASS! The top cylinders, which allow the raising and lowering of the glass, have been carefully tested for proper tension.
  • Page 18 1. Be sure mini top hardware is level front to back by placing a level along the top of the mini top housing at each hinge location. If it is not, you will need a shim kit before you can correct. Order from Hussmann Chino.
  • Page 19 Rev. 0303 2. CHECK CLOSING ACTION OF THE GLASS PANEL Test each panel by gently pushing it to close. Does the glass panel bounce or wobble as it closes? A glass panel that does not close smoothly and neatly, most likely is misaligned with the front edge of the glass and the surface or edge which it closes upon.
  • Page 20 In most cases the center hinge is the first candidate, but if the arm/mini-cam is at its maximum or minimum position, then obviously the outer hinges must be used. Top edges of glass (hinge side) Hinge Hardware Bottom edges of glass IGSV-ESC-0303...
  • Page 21 Rev. 0303 6. VERTICAL AND FRONT TO BACK ADJUSTMENT AND OPENING OVERLAP PROBLEMS • V ERTICAL DJUSTMENT 1. Remove 2. Lift open 3. Loosen hex screw top glass glass panel(s) and panel and relieve enclosing tension on mini-top hinge. hardware. •...
  • Page 22 THIS INFORMATION IS ON A PLATE LOCATED ON THE CASE ITSELF. all the set screws along the top edge of the glass panel (3mm set screw) 4. Slide glass panel in desired direction or remove panel IGSV-ESC-0303 Back of Case Inside of Case...

  • Page 23: Maintenance

    TOWARD THE MOTOR. COPPER COILS The copper coils used in Hussmann merchandisers may be repaired in the field. Materials are available from local refrigeration wholesalers. Hussmann recommends using #15 Sil-Fos for repairs.

  • Page 24: Case Specifications

    IGSV-ESC-0303 Case Specifications...

  • Page 25: Electrical Schematics

    Rev. 0303 Electrical Schematics...
  • Page 26 IGSV-ESC-0303...
  • Page 27 Rev. 0303...
  • Page 28 IGSV-ESC-0303...
  • Page 29 Rev. 0303...
  • Page 30 IGSV-ESC-0303...
  • Page 31 Rev. 0303...
  • Page 32 IGSV-ESC-0303...
  • Page 33 Rev. 0303...
  • Page 34 IGSV-ESC-0303...
  • Page 35 Rev. 0303...

  • Page 36: Appendices

    It is expected that all refrigera- tors will keep food at the FDA Food Code 1993 temperature for potentially hazardous food. 1.1 The following recommendations are made for the purpose of IGSV-ESC-0303...

  • Page 37: Appendix D. - Recommendations To User

    Rev. 0303 arriving at easily taken and understood data which, coupled with other observations, may be used to determined whether a display refrigerator is working as intended: a) INSTRUMENT – A stainless steel stem-type thermometer is recommended and it should have a dial a minimum of 1 inch internal diameter.
  • Page 38 Make sure that all refrigeration equipment is installed and adjusted in strict accordance with the manufacturer’s recommendations. See that all storage and refrigeration equipment is kept in proper working order by routine maintenance. Appendices, cont’d IGSV-ESC-0303...
  • Page 39 On Hussmann refrigeration systems, an additional (4) year extended warranty for the motor/compressor assembly is available, but must be purchased prior to shipment to be in effect. Hussmann reserves the right to inspect the job site, installation and reason for failure.

  • Page 40: Hussmann ® Chino 13770 Ramona Avenue • Chino, California

    The MODEL NAME and SERIAL NUMBER is required in order to provide you with the correct parts and information for your particular unit. They can be found on a small metal plate on the unit. Please note them below for future reference. MODEL: SERIAL NUMBER: IGSV-ESC-0303...

Table of Contents