Related Manuals for Hussmann ESS
Summary of Contents for Hussmann ESS
- Page 1 ESSS / ESS Self Service Cases (Match ESC / ESCS) p/n IGSS-ESSS / ESS-0303 INSTALLATION & OPERATION GUIDE...
-
Page 2: Table Of Contents
(800) 395-9229 General Instructions THIS BOOKLET CONTAINS INFORMATION ON: ESSS: Refrigerated Self Service cases Matches Multideck Ser- ESS: Refrigerated Self Service Case (Matches Single Deck SHIPPING DAMAGE All equipment should be thoroughly examined for ship- ping damage before and during unloading. -
Page 3: Cut & Plan Views
Rev.0303 ESSS 36" " 31" " Self-Service Scale = 1/2" 8" DRAIN AND REFRIG. ELECTRICAL MECHANICAL MECHANICAL STUB UP STUB UP AREA AREA 18" X 18" 18" X 18" CASE FRONT 1" 8'-2" (VARIABLE LENGTHS) (ESSS) Plan View Scale = 1/4" Cut &... -
Page 4: Installation
6. Apply bead of silicone to top of bulkheads. 7. Slip on stainless steel bulkhead cap. Also apply silicone to seam between overhead light tubes. 8. Recheck all camlocks. JOINING - ESS 1. Using a 7mm Allen Wrench, lock in and close the three camlock. IGSS-ESS/ESSS-0303... -
Page 5: Joint Trim
Rev.0303 Do not use cam locks to pull cases together. 2. Secure joint backer. Located behind cart bumper suport at joints. To adjust screws holding bumper cart to case on either side or the joint and slide extrusion to center of joint. This piece supports the fornt panel at the joint. -
Page 6: Plumbing
Armstrong’s Armaflex. b. Where condensate drains are located in dead air spaces (between refrigerators or between a refrigerator and a wall), provide means to prevent freezing. The water seal should be insulated to prevent condensation. IGSS-ESS/ESSS-0303... -
Page 7: Refrigeration
Rev.0303 REFRIGERANT TYPE The standard refrigerant will be R-22 unless otherwise specified on the customer order. Check the serial plate on the case for information. PIPING The refrigerant line outlets are located under the case. Locate first the electrical box, the outlets are then on the same side of the case but at the opposite end. -
Page 8: Electrical
Actual ampere draw may be less than specified. Field wiring from the refrigeration control panel to the merchandisers is required for re- frigeration thermostats. Most component amperes are listed in the “Case Specs” section, but always check the serial plate. -
Page 9: Joint Trim
Hussmann cases were not designed to “heat up” or “cool down” product—but rather to maintain an item’s proper temperature for maximum shelf life. To achieve the pro- tection required always: 1. -
Page 10: Case Cleaning
Wax should be applied in a thin even coat and brought to a high polish by rubbing lightly with a dry clean soft cloth, such as a cotton flannel. Excessive rubbing may cause scratching and/or buildup an electrostatic charge which IGSS-ESS/ESSS-0303... -
Page 11: Plexiglass Repair
Rev.0303 attracts dust and dirt to the surface. Blotting with a clean damp cloth is recommended to remove charge. ANTISTATIC COATINGS For acrylic used indoors, antistatic coatings successfully prevent the accumulation of an electrostatic charge for periods of several months—if the surface is not washed or wiped down with a wet cloth. -
Page 12: Maintenance
Should fans or blades need servicing, always replace fan blades with the raised embossed side of the blade TOWARD THE MOTOR. COPPER COILS The copper coils used in Hussmann merchandisers may Maintenance be repaired in the field. Materials are available from local refrigeration wholesalers. -
Page 13: Specifications
Meat / Fish NOTES:These refrigerated merchandisers have been designed for use in stores where temperatures and humidity are maintained at or below 75°F and 55%RH. Stores are responsible for setting their cases approprately in conditions which vary from the above. The number of defrosts and/or the duration may vary... -
Page 14: Electrical Schematics
IGSS-ESS/ESSS-0303 Electrical Schematics... - Page 15 Rev.0303...
- Page 16 IGSS-ESS/ESSS-0303...
- Page 17 Rev.0303...
- Page 18 IGSS-ESS/ESSS-0303...
- Page 19 Rev.0303...
-
Page 20: Appendices
1 inch internal diameter. A test thermometer scaled only in Celsius or dually scaled in Celsius and Fahrenheit shall be accurate to 1°C (1.8°F). Temperature measuring devices that are scaled IGSS-ESS/ESSS-0303... -
Page 21: Appendix D. - Recommendations To User
Rev.0303 only in Fahrenheit shall be accurate to 2°F. The thermometer should be checked for proper calibration. (It should read 32°F when the stem is immersed in an ice water bath). b) LOCATION – The probe or sensing element of the thermometer should be located in the airstream where the air first enters the display or storage area, and not more than 1 inch away from the surface and in the center of the discharge opening. - Page 22 IGSS-ESS/ESSS-0303...
- Page 23 On Hussmann refrigeration systems, an additional (4) year extended warranty for the motor/compressor assembly is available, but must be purchased prior to shipment to be in effect. Hussmann reserves the right to inspect the job site, installation and reason for failure.
-
Page 24: Hussmann ® Chino 13770 Ramona Avenue • Chino, California
The MODEL NAME and SERIAL NUMBER is required in order to provide you with the correct parts and information for your particular unit. They can be found on a small metal plate on the unit. Please note them below for future reference. MODEL: SERIAL NUMBER: IGSS-ESS/ESSS-0303...