Parts And Their Functions; O Front Panel - Panasonic AJ-HD1700PE Operating Instructions Manual

Parts and Their Functions

Front panel
5 1 6 7 2
POWER OFF ON
1 2 3 4 5 6 7 8 CUE
CH
CH CONDITION MONITOR FULL/FINE REMOTE
9P 50P RS-232C
L R
HEADPHONES
SHIFT F1 F2 F3
ABC DEF GHI
AUDIO CH SELECT
7 8 9
1 5 2 6 3 7 4 8
CH CH CH CH CH CH CH CH PREVIEW/
JKL MNO PQRS REVIEW
4 5 6 BS
AUTO
TUV WXYZ
EDIT
1 2 3 ENT
PUSH
LOCK
0 C T F
REC P8 REC P8 REC P8 REC P8
FULL
1 POWER switch
2 Audio level meter
The audio information is displayed here.
• The levels of the CH1, CH2, CH3, CH4, CH5,
CH6, CH7 and CH8 PCM audio signals and level
of the CUE track signal are displayed here.
• The levels of the input signals are displayed
during recording and when E-E is selected.
During playback, the levels of the playback
signals are displayed. In the INPUT CHECK
status, the levels of the input signals are
displayed for CH1 to CH8.
• Input signal display for each of the channels
The indicators for the selected input signals light.
(SDI lights when the SD SDI input signal is
selected.)
If an input signal has been selected but it has not
actually been input,the AES, HDSDI, SDI or
SDTI indicator will blink if a signal corresponding
to one of these indicators was selected whereas
the ANA indicator will remain lighted if it was an
ANA signal that was selected.
When the internal signal (INT SG) has been
selected, all the AES, ANA, HDSDI, SDI and
SDTI indicators light.
All the indicator are off in the 23/24 Hz mode or
25 Hz (HD or SD) mode.
AES ANA AES ANA
HD SDI SDTI HD SDI SDTI
dB dB
0
-4 •4 -16 •16
-8 •3 -17 •12
-12 •2 -18 •8
-16 •1 -19 •4
-20 0 -20 0
-25 -1 -21 -5
-30 -2 -22 -10
-40 -3 -23 -20
- -4 -24 -
L R L R
8
3 4
EJECT
XL/L/M -cassette
Do not insert S-cassette
without adapter
SHTL JOG VAR
ADJUST
HOME RF1 RF2 ASSEM PUSH-INTER
VIDEO TC CUE
UNITY
INSERT
REV FWD
AUDIO UNITY DIAG MENU
STAND BY PLAYER RECORDER INPUT CHECK
F4 F5 F6
SERVO REC INHIBIT
EDIT PLAY REC
A IN A OUT
PRE-
ROLL
TRIM
REW STOP FF
SET
IN OUT
FULL
Input signal display
Level meter
Reference level (j18 dB)
(AJ-HD1700E)
Reference level (j20 dB)
(AJ-HD1700P)
Left (L) and right (R)
monitor channel displays
3 Cassette insertion slot
If the slot's orange plate is visible, it means that a
cassette tape is already inserted.
4 EJECT button
When this button is pressed, the cassette is
unloaded, and a few seconds later it is ejected
automatically.
When CTL appears on the counter display, the
display is reset.
5 Headphones jack
The sound heard during recording, playback or
editing can be monitored through headphones
when stereo headphones are connected to this
jack.
6 Volume control dial
This control dial is used to adjust the volume level
of the headphones and monitor output.
Whether the volume level of the monitor output is to
be coupled together with that of the headphones to
this dial or separated can be selected using the
setup menu item No.712 (MONI OUT). (Note that
the volume level of the headphones is coupled at all
times.) When the volume levels have been
separated, the UNITY value (prescribed value)
applies to the monitor output.
7 Channel condition lamps
These lamps light to indicate the error rate
status.
(Green " amber " red)
Green: This lights when the error rates for the
video and audio playback signals are both at
acceptable levels.
Amber: This lights when the error rate for either the
video or audio playback signals has deteriorated.
The playback picture
unaffected even while this lamp is lighted.
Red: This lights when correction or interpolation
has been engaged for either the video or audio
playback signals.
and sound remain