Table of Contents
Advertisement
Function menus
<50P IN/OUT ASSIGN>
Registering functions in the input pins/Active inputs
Registering functions in the output pins/Active outputs
1.
Selecting the 50-pin connector pins
Turn the ADJ dial to move the selection marker and
select the pin of the 50-pin connector into which the
menu item is to be registered.
2.
Entering the 50-pin connector pins
Press the ADJ dial.
The entered 50-pin connector pin display is highlighted.
3.
Selecting the menu item
Turn the ADJ dial and select the menu item for the pin
of the 50-pin connector which was selected in step 1
above.
4.
Entering the menu item
Press the ADJ dial.
The on-screen setting display now blinks.
5.
Selecting the setting
Turn the ADJ dial and select the setting for the
menu item which was selected in step 3 above.
6.
Entering the setting
Press the ADJ dial.
What is to be operated by the ADJ dial returns to the
front panel.
Whatever was selected in step 3 is
displayed as the registered item name and whatever was
selected in step 5 is displayed as the registered value.
7.
To select menu items and settings for other 50-pin
connector pins, repeat steps 1 to 6.
8.
Saving the data in the 50-pin registration file
To save what has been set in the 50-pin connector in
the 50-pin registration file, press
If
(EXIT) is pressed without the above settings
F6
have been saved, those settings will be canceled.
Clearing
1.
Turn the ADJ dial to move the selection marker and select the
pin of the 50-pin connector whose menu item is to be cleared.
2.
Press
(RESET). The registered item name
F4
and registered value displays now go blank.
3.
To clear the menu items in other 50-pin connector
pins, repeat steps 1 and 2.
4.
To save what has been set in the 50-pin connector in
the 50-pin registration file, press
If
(EXIT) is pressed without the above settings
F6
have been saved, those settings will be canceled.
Resetting all the items and values
Press
All the registered item names and registered values
are now set to the factory settings. (These settings
cannot be restored.)
Special IN menu list
No.
SUPER
DISPLAY
Functions not featured on the setup menua
B00
STBY ON
B01
STBY OFF
B02
STBY ONOFF
B03
EJECT
B04
CUE
B05
IN SET
B06
STILL
B07
422 REM ON
B08
422 REM OFF
B09
TC EXT
(SET).
F5
B10
TC INT AUTO
B11
TC EXT_L
REG
SRC PROTECT and STOP PROTECT settings switched simultaneously
B20
PROTECT
HALF
B21
PROTECT
T-REL
(SET).
F5
(RESET) while holding down the
F4
Description of setting
For transferring to the STANDBY ON mode.
For transferring to the STANDBY OFF mode.
For alternately transferring to the STANDBY ON
and OFF mode.
For transferring to the EJECT mode.
For prerolling the tape to the IN point when the
IN point has been registered; for prerolling the
tape to the current point when the IN point has
not been registered.
For registering the edit IN point.
For transferring to the still picture (STILL) mode.
The 9-pin connector functions.
The 9-pin connector does not function.
For returning TC SOURCE to the previous EXT
mode.
(No switching occurs if the EXT mode is
currently established.)
For switching TC SOURCE to INT and TCG
MODE to AUTO.
For switching TC SOURCE to EXT_L and TCG
MODE to REGEN.
For switching the tape protection mode operation to
half-loading in the event that the VTR has been left
standing in the STOP mode or the STILL mode while
any of the search modes (JOG, VAR or SHTL) was
established.
For switching the tape protection mode operation to
tension release when the VTR has been left standing
in the STOP mode or the STILL mode while any of the
search modes (JOG, VAR or SHTL) was established.
50P IN/OUT
ASSIGN
button.
F
73
Advertisement
Table of Contents
