Table of Contents
Advertisement
Page 6
GEM-DXRP1 / GEM-DXK1 Keypad Easy Program Menu
To create a custom program using the GEM-DXRP1 / GEM-DXK1 keypad, simply answer the following questions and record your informa-
tion on the Easy Menu Programming Worksheet. In each of the following steps, press
forwards, the PRIOR ("X" or
# o f Z n s i n A r e a 1
E n t e r # Z o n e s X X
(Direct Entry)
E Z Z o n e D o u b l i n g
E n a b l e d ?
Y / N
(Press YES or NO)
F i r e
Z o n e s
E n t e r Z o n e # ° °
(Direct Entry)
R e p o r t A l l Z o n e s
T o C e n t r a l ? Y / N
(Press YES or NO)
E x i t / E n t r y Z o n e s
E n t e r Z o n e #
(Direct Entry)
I n t e r i o r Z o n e s
E n t e r Z o n e #
(Direct Entry)
2 4 H o u r Z o n e s
E n t e r Z o n e #
(Direct Entry)
LIBRA LIB-P432EX Series Programming Instructions
u
q
) to go backwards,
Total Number of Zones in Area 1 (New Program Only)
•
Enter the total number of zones to be programmed for Area 1.
•
Valid entries are from 01 to 32. Directly enter the total number of zones, including leading zeros.
•
The system is based on groups of 4 zones each (after the first 8 zones), and will automati-
cally round up to the next group of 4. For example, if you enter 18, it will automatically con-
vert this to 20 zones. Press
Panel Zone Doubling (New Program Only)
•
To double the number of hardwired panel zones from 8 to 16, press
•
If Panel Zone doubling is not desired, press
•
The 16 zones will remain EOL terminated zones, requiring Normally Closed devices only.
•
Refer to Wiring Diagram and Installation Instructions for wiring instructions
Fire Zones in Area 1 (New Program Only)
•
Enter the zone number of any Fire Zones (including 2-wire, 4-wire or wireless).
•
Valid entries are from 01 to 32.
•
Directly enter each zone number, including leading zeros, and press
peat for any additional zone(s). Press
Local or Central Station Reporting System (New Program Only)
Press
p
for all zones to report; press
Exit/Entry Zones in Area 1 (New Program Only)
•
Enter the zone numbers of zones to be used as Exit/Entry zones.
•
Valid entries are from 01 to 32. Directly enter each zone number, including leading zeros.
X X
u
•
Press
to save and repeat for any additional zone(s); press
NOTE: Exit/Entry Entry time of 30 seconds will automatically be programmed.
Interior Zones in Area 1 (New Program Only)
•
Enter the zone numbers to be used as Interior Zones.
•
Valid entries are from 01 to 32. Directly enter each zone number, including leading zeros.
X X
u
•
Press
to save and then repeat for any additional zone(s).
•
Press
p
to proceed.
•
All Interior zones will also be automatically programmed as "Exit/Entry Follower" and as "Power
Up Delay" zones.
24 Hour Zones in Area 1 (New Program Only)
•
Enter the zone numbers of zones to be used as 24 Hour zones.
•
° °
Valid entries are from 01 to 32. Directly enter each zone number, including leading zeros.
u
•
Press
to save and repeat for any additional zone(s); press
NOTE: 24 Hour Zones will automatically be programmed as audible (Burg Output).
w
to save and
y
twice to exit at any time.
u
to save. Press
q
p
q
to set cursor, the NEXT ("r" or
p
to proceed.
p
.
u
to proceed.
for local system
p
to proceed.
p
to proceed.
NAPCO Security Systems
p
) to go
.
to save, and then re-
Advertisement
Table of Contents
