Carrier Omnizone 50BVC Installation, Start-Up, Service And Controls Operation And Troubleshooting page 83

PROTOCOL MAP
READ/
DISPLAY NAME
WRITE
Input Register
Cooling Percentage R
Holding Regis-
Cooling Set point R/W
CSAT_HI R Discrete Input
Input Register
Current Alarm R
CWV Command R Discrete Input
CWV_FAIL R Discrete Input
CWV_HAND R Discrete Input
DA_SENS_FAIL R Discrete Input
Damper Output
R Discrete Input
Cmd
DAT Sensor Selec- Holding Regis-
R/W
tion
DAT Sensor Source Input Register
R
Selection Status
DAT_HI R Discrete Input
Holding Regis-
Demand Level R/W
DO_LOCK R Discrete Input
DPS Alarm R Discrete Input
DX_RNTM R Discrete Input
Table 66 — Integration Points List (cont)
MODBUS
REGISTER REGISTER REFERENCE
TYPE NUMBER NAME
9 clg_pct
(Float)
57 sat_stpt_cl
ter (Float)
28 csat_hi
11 current_alarm
(Float)
cwv_com-
29
mand
30 cwv_fail
31 cwv_hand
32 da_sen
33 damper_cmd
15 dat_sel
ter (Float)
13 dat_sel_sta
(Float)
34 dat_hi
17 demand_level
ter (Float)
35 do_lock
36 DPS_alarm
37 dx_rntm
BACNET
OBJECT OBJECT
NV NAME
TYPE ID
AV 13 nvoClgPct
AV 66
BV 80
nvoCurAl
AV 17
m
nvoCwvCo
BV 109
mmand
BV 107
BV 108
BV 31
nvoDamp-
BV 49
erCmd
AV 81
AV 82
BV 29
AV 64
BV 37
BV 77
BV 79
83
LONWORKS OPERATION
SNVT DESCRIPTION
Network Status of Cool-
SNVT_count_inc(
ing Demand in percent-
9)
age (%)
Network Parameter to
Select set the Cooling Set point
55 °F (Default)
Network Parameter to
set CSAT HI
Select 0 = Hardwired Sensor
(Default)
1 = BAS Sensor Value
Alarm Status of unit:
0 = No Alarm
1-7 = UPM1 Fault Code
9-16 =UPM2 Fault Code
20 = Output Overridden
via Keypad
30 = Sensor Failure
40 = Leaving Water
Temp Alarm
SNVT_count_inc(
50 = Zone Temp Alarm
9)
60 = Discharge Air Tem-
perature
70 = Filter Alarm/Com-
pressors 1 & 2 Runtime
90 = High CO
Alarm
100 = Supply Fan
Locked
110 = Static Press Low
Condenser Water Valve
Command Status
SNVT_switch(95)
0 = Off
1 = On
Condenser Water Valve
Select
Failure Alarm
Condenser Hand Alarm
Condenser Valve Com-
Select
mand Enabled without
unit commanded
Network Alarm Indicat-
ing Discharge Air Sen-
Select sor Failure
0 = Normal
1 = Alarm
Damper Output Status
SNVT_switch(95) 0 = Closed
1 = Open
Discharge Air Tempera-
ture Sensor Setup
0 = Hardwired Sensor
Select
(Default)
1= BAS Supplied DAT
value
Discharge Air Tempera-
ture Sensor Selection
Status
Select
0 = Hardwired Sensor
DAT
1 = BAS Supplied DAT
Discharge Air Tempera-
ture Sensor Alarm (Cool-
ing)
Select
0 = Normal
1 = High DAT (Default:
>70 °F)
Demand Level Set point
Select
Adjust in °F
Network Parameter to
set DO LOCK
Select 0 = Hardwired Sensor
(Default)
1 = BAS Sensor Value
Network Parameter to
set DPS Alarm
Select 0 = Hardwired Sensor
(Default)
1 = BAS Sensor Value
Network Parameter to
set DX RNTM
Select 0 = Hardwired Sensor
(Default)
1 = BAS Sensor Value
2 Level