Carrier Omnizone 50BVC Installation, Start-Up, Service And Controls Operation And Troubleshooting page 82

PROTOCOL MAP
READ/
DISPLAY NAME
WRITE
Comp1 Runtime
R/W
Rst
Comp2 Runtime
R/W
Rst
Comp3 Runtime
R/W
Rst
Comp4 Runtime
R/W
Rst
Compressor 1 Sta-
R Discrete Input
tus
Compressor 2 Sta-
R Discrete Input
tus
Compressor 3 Sta-
R Discrete Input
tus
Compressor 4 Sta-
R Discrete Input
tus
compressor control Input Register
R
status
Input Register
Compressor Stages R
Holding Regis-
Compressors mode R/W
CON R Discrete Input
CON2 R Discrete Input
Condenser Valve
R Discrete Input
Status
Continuous Fan R/W
Holding Regis-
Control Source R/W
Cooling Econo R Discrete Input
Table 66 — Integration Points List (cont)
MODBUS
REGISTER REGISTER REFERENCE
TYPE NUMBER NAME
cmp1_rnt-
Coil 4
m_rst
cmp2_rnt-
Coil 5
m_rst
cmp3_rnt-
Coil 6
m_rst
cmp4_rnt-
Coil 7
m_rst
3 comp1_status
2 comp2_status
1 comp3_status
4 comp4_status
comp_c-
5
(Float) trl_status
7 cmp_stgs
(Float)
11 comp_mode
ter (Float)
24 con_2st
25 con_4st
cond_vlv_sta-
26
Coil 8 Cont_fan
13 ctrl_source
ter (Float)
27 clg_econ
BACNET
OBJECT OBJECT
TYPE ID
BV 13
BV 14
BV 68
BV 70
BV 152
BV 153
BV 156
BV 159
AV 60
AV 14
AV 70
BV 9
BV 57
BV 105
tus
BV 18
AV 15
BV 63
82
LONWORKS
NV NAME SNVT
nviC- Compressor 1 Runtime
mp1Rn- SNVT_switch(95) Reset. Momentary On/
tRst Off required.
nviC- Compressor 2 Runtime
mp2Rn- SNVT_switch(95) Reset. Momentary On/
tRst Off required.
nviC- Compressor 3 Runtime
mp3Rn- SNVT_switch(95) Reset. Momentary On/
tRst Off required.
nviC- Compressor 4 Runtime
mp4Rn- SNVT_switch(95) Reset. Momentary On/
tRst Off required.
Network Parameter indi-
Select cating the status of Com-
pressor 1
Network Parameter indi-
Select cating the status of Com-
pressor 2
Network Parameter indi-
Select cating the status of Com-
pressor 3
Network Parameter indi-
Select cating the status of Com-
pressor 4
Compressor Control Sta-
tus
Select
0 = Zone Control
1 = Discharge Air Control
Compressor Stages
Configured Status
1 = 1 Compressor 1
Stage
2 = 2 Compressor 2
nvoCmp- SNVT_count_inc(
Stages
Stgs 9)
3 = 3 Compressor 3
Stages (3 and 4 Stage
units only)
4 = 4 Compressor 4
Stages (50BV Default)
Compressor Mode Setup
0 = Zone
Select
1 = Discharge Air Control
(Default)
UPM Board 1 Conden-
sate Alarm
Select
0 = Normal
1 = Condensate Alarm
UPM Board 2 Conden-
sate Alarm
Select
0 = Normal
1 = Condensate Alarm
Condenser Valve Status
(Closed to Enable Com-
pressor Operation)
Select 0 = Compressor Opera-
tion Disabled
1 = Compressor Opera-
tion Enabled
Run Fan continuously
During Occupancy Mode
Setup
Select 0 = Cycle Fan with Com-
pressor Operation
1 = Run Fan when Occu-
pied (Default)
Control Source for Occu-
pancy Setup
0 = Digital Input 1
1 = Keypad Schedule
Select 2 = BAS Occupancy
Command
3 = Factory Use
4 = Manual On-Continu-
ous (Default)
Network Parameter to
set Cooling Econo tem-
perature
Select
0 = Hardwired Sensor
(Default)
1 = BAS Sensor Value
OPERATION
DESCRIPTION