Table of Contents
Advertisement
Laying pipes backwards,rightwards and downwards
Piping
Pipe layout
Put refrigerant pipe and drainage pipe together,
wrap them with band.
Take care not to raise
the drainage hose.
Cut this part when
connecting pipe rightwards.
Insert the refrigerant pipe and drainage pipe into the wall
hole sleeve
,hang the indoor unit's upper half on the
C
mounting plate
.
1
Move the air conditioner right and left to check if it is hung
on the mounting plate
Push the unit's lower half into the mounting plate
Lay pipes leftwards or rear leftwards
Pipe layout
Put refrigerant pipe and drainage pipe together,
wrap them with band first and then with felt tape
Take care not to raise
the drainage hose.
Felt tape
(Pipe band
Wrap the pipe from pipe end
with felt tape
(The folded
5
part of the felt tape
shall
5
be one third of its width).
Refitting for drainage hose
The drainage hose should be refitted in the event of
piping leftwards and rear leftwards.Otherwise,water
dripping may result.
Drainage hose
1.The rubber stopper at the rear right of indoor unit.
Remove the rubber stopper by grasping the sharp lug.
2.Remove the drainage hose at the rear left side of
the indoor unit.
Pull out the drainage hose by grasping the handle knob shown
by arrow
in the direction.
Cut this part when connecting
pipe downwards .
Cut this part when
connecting pipe downwards.
firmly.
1
Cut this part when
connecting pipe leftwards.
5
)
Ｅ
Use a tape to fix the
end of the felt tape
Drainage rubber stopper
Rubber stopper
Drainage hose
3.
Slip the rubber stopper into the position in which the
drainage pipe is installed at the rear of indoor unit.
Use an Allen key to press the stopper into the joint of the drain
plate.
Connect the drainage hose to the corresponding
4.
connection position at the rear right of indoor unit.
Insert the drainage hose in the joint of the drain plate.Be sure to
confirm if the hose is clamped into the prominent detent.
Connection between the refrigerant pipe and
extension pipe
If extension pipes or wires have been buried into a wall,please
perform piping as described in the following key points.
.
1
①Hook the mounting plate
considering inclusion of the pipe and placing the unit as possible
as close to the left,cut off a piece of packing material (used as liner)
to lock the rear lug,raise the indoor unit as shown in right figure..
·Connect the refrigerant pipe and extension pipe
Cut off a part of packing material (used as liner)
.
Lock the rear lug
5
Wrap the rest of
cut material.
Fix the end with
masking tape.
.
5
Installation of indoor unit
Pass the pipe through the wall,hang and install the unit
on the mounting plate
is heard.
2-7 Laying drainage pipe
In order to make a smooth drainage,the drainage pipe shall
be connected tilting downwards.(Figure 1)
Don't connect the pipe as shown in Figure 2-3.
Tilting
downwards
Leakage
(Figure 1)
(Figure 2)
If it is not long enough for the drainage hose installed at the
indoor unit,you can use the drainage hose
for connection.
When the hose goes through room,be sure to bind up
the drainage hose with commercially available insulated
material.
Drainage rubber stopper
Drainage hose
1
with indoor unit's upper part.After
Indoor unit packing
cardboard
Cut off the cardboard with
a scissor or cutting tool.
As shown right,
put the liner to
a notch of rear
lug firmly,while
paying attention
the direction.
,then push in the unit until a click
1
Indoor unit
Mounting plate
Press the hook in the hole
of the mounting plate
1
Don't lift
Drain occlusion
Air
Wave shape
The pipe end
soaked in water
(Figure 3)
F
B
.
Liner
1
Below 5cm from
the ground
(Figure 4)
in accessory
35
Advertisement
Chapters
Table of Contents
