Nortel 600 Series Manual page 57
Dip switch settings for printed circuit packs and balance networks
Hide thumbs
Also See for 600 Series:
- Installation manual (94 pages) ,
- Installing (80 pages) ,
- Install manual (218 pages)
Advertisement
Table 2-AV:
NT3T72AE I/O Bus Extender pack - S2 switch settings - switches 1-4
Type of Shelf
CPU/Network
CPU/Network
CPU/Network
CPU/Network (DMS-10
EN)
CPU/Network (DMS-10
EN)
CPU/Network (DMS-10
EN)
CPU/Network (DMS-10
EN)
GPIO (DMS-10 EN)
GPIO (DMS-10 EN)
GPIO (DMS-10 EN)
GPIO (DMS-10 EN)
GPIO (DMS-10 EN)
GPIO (DMS-10 EN)
GPIO
GPIO
GPIO
GPIO
Table 2-AW:
NT3T72AE I/O Bus Extender pack - S2 switch settings - switches 5-8
NT3T72
All 3T72s are AD or higher.
All 3T72s are AD or higher.
All 3T72s are not AD or higher.
August 2006
Pack Location
(bsp)
CE 3
3
8 (J1T72A-1/B-1) or
7 (J1T72C-1)
CE 3
2
14/15 (J1T72B-1) or
13/14 (J1T72C-1)
CE 3
3
14/15 (J1T72B-1) or
13/14 (J1T72C-1)
CE 1 4
9 (J8M75A-1)
CE 1 5
9 (J8M75A-1)
CE 1 4
10/11 (J8M75A-1)
CE 1 5
10/11 (J8M75A-1)
CE 1 2
2/3 (J1T81A-1)
CE 1 2
19/20 (J1T81A-1)
CE 1 3
2/3 (J1T81A-1)
CE 1 3
19/20 (J1T81A-1)
CE 3 1
2/3 (J1T81A-1)
CE 3 1
19/20 (J1T81A-1)
CE 3 1
2/3 (J1T81A-1)
CE 3 1
19/20 (J1T81A-1)
CE 1 1
2/3 (J1T81A-1)
CE 1 1
19/20 (J1T81A-1)
Settings: 1 = ON, 0 = OFF, - = NOT APPLICABLE.
Note:
CAUTION: Incorrect address settings may cause system problems and a serious
degradation of service. For example, duplicating an address setting across two
different NT3T72 packs will result in conflicts.
NT3T70
BB or higher
BA or lower
Do not care
Settings: 1 = ON, 0 = OFF, - = NOT APPLICABLE.
Note:
For Generic 602.20
Switch settings for printed circuit packs
08.01
Switches
1
2
3
4
0
0
0
0
0
1
0
0
1
1
0
0
0
0
0
0
0
0
0
0
0
1
0
0
1
1
0
0
0
1
1
0
1
1
1
0
0
0
0
1
1
0
0
1
0
1
1
0
1
1
1
0
0
1
1
0
1
1
1
0
0
0
0
1
1
0
0
1
Switches
5
6
7
8
-
-
-
0
1
-
-
-
1
-
-
-
NTP 297-3601-316
2-50
Advertisement
