Table of Contents
Advertisement
5.
Function setting list
(1) Function setting list
Table 1.
No.
Item
P01 Maximum sewing
The maximum sewing speed reached by fully depressing the pedal is set with
speed
this function setting item. The maximum sewing speed can be changed within
the sewing speed range specified for [P68 Maximum sewing speed].
* The maximum sewing speed can also be changed using the + - switch
P02 Tilt of the pedal
Change in the sewing speed with respect to the depressing depth of the pedal
is set with this function setting item.
The sewing speed is increased abruptly when this parameter is set to a large
value, or increased slowly when this parameter is set to a small value.
P04 Reverse feed
The sewing speed to be used during the reverse feed stitching at the
stitching speed at
beginning of sewing is set with this function setting item.
the beginning of
sewing
P05 Reverse feed
The sewing speed to be used during the reverse feed stitching at the end of
stitching speed at
sewing is set with this function setting item.
the end of sewing
P06 Overlapped stitching
The sewing speed to be used during the overlapped stitching is set with this
speed
function setting item.
* This speed can also be changed using the relevant switch on the
*
P07 Sewing speed for
The sewing speed for soft start at the beginning of sewing is set with this
soft start
function setting item.
*
P08 Soft start function
The number of stitches to be sewn with the soft-start function at the beginning
of sewing is set with this function setting item.
P09 Sewing speed for
Sewing speed for the polygona-shape stitching is set with this function setting
the polygonal-shape
item.
* The sewing speed can also be changed using the + - switch on the
stitching
P10 Setting of the
Whether the reverse feed stitching is automatically carried out at the end of
reverse feed
polygonal-shape stitching is set with this function setting item
stitching at the end
of end of polygonal-
shape stitching
P12 Changeover of
The sewing speed for the reverse feed stitching at the beginning of sewing is
the reverse feed
set with this function setting item.
stitching at the start
of sewing between
Auto / Manual
*
P13 Function of stop
Operation to be carried out at the end of the reverse feed stitching at the
immediately after
beginning of sewing is selected with this function setting item.
the reverse feed
stitching at the
beginning of sewing
*
P15 Changeover of the
The function of needle up/down correction switch is changed over with this
needle up/down
function setting item.
correction function
P16 Limited speed during
Limited speed in the case of carrying out the reverse feed stitching operation
the reverse feed
is set with this function setting item.
stitching on the way
*
P18 Correction of
Stitch alignment can be carried out by changing the timing of actuating the
solenoid-on timing
reverse-feed stitching solenoid at the time of reverse feed stitching at the
for the reverse feed
beginning of sewing. When the set value for this parameter is increased, the
stitching at the
length of stitch at the end of A process is increased and the length of stitch at
beginning of sewing
the beginning of B process is decreased.
P19 Correction of
Stitch alignment can be carried out by changing the timing of releasing the
*
solenoid-off timing
reverse-feed stitching solenoid at the time of reverse feed stitching at the
for the reverse feed
beginning of sewing. When the set value for this parameter is increased, the
stitching at the
length of stitch at the beginning of B process is increased.
beginning of sewing
P21 Position to depress
Start position of sewing by operating the pedal is set with this function setting
the front part of
item.
pedal (sewing start
position)
P22 Pedal freeing
Releasing position of pedal operation is set with this function setting item.
position
＊ Supplementary explanation is added in 4.-(2) Further information about memory switch.
◎ These data are stored in the main board in the control box. Data other than these data are stored in the panel board in the panel.
Description
on the operation panel.
operation panel.
0 : The soft-start function is not selected
1 to 9 : The number of stitches to be sewn with the soft-start function
operation panel.
ON : Reverse feed stitching is automatically performed at the end of
sewing
OFF : Sewing machine stops sewing before starting reverse feed stitching
at the end of sewing. It performs reverse feed stitching when the
front part of pedal is depressed.
0 : The reverse feed stitching is performed by manually operating the
pedal.
1 : The reverse feed stitching is performed at the sewing speed set with [P04
Reverse feed stitching speed at the beginning of sewing].
CON : The sewing machine does not stop temporarily after completion of
the reverse feed stitching at the beginning of sewing
STP : The sewing machine stops temporarily after completion of the
reverse feed stitching at the beginning of sewing
0 : Needle up/down correction
1 : One stitch correction
2 : Continuous half stitch
3 : Continuous one stitch
0 : No speed limit
10 to 3000 : Sewing is performed at the set sewing speed
– 89 –
Setting
Setting range
Default
levle
100 to [P68]
MS : 4000
U
（sti/min）
SH : 3500
10 to 100
S
80
（%）
100 to 3000
U
1900
(sti/min)
100 to 3000
U
1900
(sti/min)
100 to 3000
U
1900
(sti/min)
100 to 1500
U
800
(sti/min)
0 to 99
U
1
(Stitches)
200 to [P68]
MS : 4000
U
(sti/min)
SH : 3500
ON/OFF
U
ON
0 to 1
U
1
(–)
CON/STP
U
CON
0 to 3
U
0
(–)
100 to 4000
S
2000
(sti/min)
0 to 200
U
123
(°)
0 to 200
U
130
(degree)
30 to 1000
S
520
(–)
30 to 1000
S
420
(–)
Advertisement
Table of Contents
