Packaging List; Introduction - Superior Fireplaces DRL2000 Series Installation And Operation Instruction Manual

Innovative Hearth Products
DRL2000 & DRL3500 Series Direct-Vent Gas Fireplaces
INSTALLATION
PACKAGING
All DRL2000 series models include
The assembled vented gas fireplace heater is packaged with:
•
•
•
•
•
•
All DRL3500 series models include
The assembled vented gas fireplace heater is packaged with:
•
•
•
•
•
•
•
•
f i r e - p a r t s . c o m
•

INTRODUCTION

These vented gas fireplace heaters are sealed combustion, air-circulating gas fireplaces designed for residential and commercial
applications.
Electronic fireplaces are designed with an electronic intermittent pilot ignition system. External electrical power is required to
operate these units. In the event of a power outage, four (4) AA batteries (in battery holder) provide backup power for fireplace
operation (excluding the blower).
NOTE: Installation and repair should be done by a qualified service person. The fireplace should be inspected before use and at
least annually by a professional service person. More frequent cleaning may be required due to excessive lint from carpeting,
bedding material, etcetera. It is imperative that control compartment, burners and circulating air passageways of the fireplace be
kept clean.
NOTE: Diagrams and illustrations are not necessarily shown to scale.
Approved Vent Components
These fireplaces are designed, tested and listed for operation and installation with the following vent components only:
•
•
•
Use only the correct size venting (4-1/2" inner and 7-1/2" outer).
These approved vent system components are labeled for identification. DO NOT use any other manufacturer's vent components
with these fireplaces.
Codes and Standards
These fireplaces comply with National Safety Standards and are tested and listed by PFS TECO (Report No. F19-008) to ANSI
Z21.88 (in Canada, CSA-2.33), and CAN/CGA-2.17-M91 in both USA and Canada, as vented gas fireplace heaters.
These fireplaces are listed for installation in bedrooms and manufactured homes.
The installation must conform to local codes or, in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1/NFPA
54—latest edition (In Canada, the current CAN/CGA-B149.1 installation code).
The fireplace, when installed, must be electrically grounded and wired in accordance with local codes or, in the absence of local
codes, with the National Electrical Code, ANSI/NFPA 70—latest edition, or the Canadian Electrical Code, CSA C22.1—latest edition.
8
Literature Kit (bag in bottom compartment containing Installation and Operation Instructions (this manual), Hot Glass Safety
Flyer, and Safety-In-Operation Warning Labels)
15 feet of two conductor wire
2.75" Non-combustible Board, 2 Side Brackets and 1 Center Bracket
35" & 45" models = 5 Lbs of Black Glass Media. (35" models use 3.5 lbs only) 55" models use = 7.5 lbs of Black
Glass Media
.
2 U-Shaped Vent Restrictors (seen on Page 24)
1 Minimal Vent Run Baffle (seen on Page 24)
Literature Kit (bag in bottom compartment containing Installation and Operation Instructions (this manual), Hot Glass Safety
Flyer, and Safety-In-Operation Warning Labels)
Elbow Heat Shield
Header heat shield
4.75" non-combustible board 2 side brackets and 1 center bracket
35" & 45" models = 5 Lbs of Platinum Glass Media. (35" models use 3.5 lbs only) 55" models use 7.5 lbs of
Platinum Glass Media.
Remote Control
1 Wall Heatshield (3500 series models only - bend wall Heatshield as shown in Figure 26, Page 34)
2 U-Shaped Vent Restrictors (seen on Page 24)
1 Minimal Vent Run Baffle (seen on Page 24)
Remarqué : L'installation et la réparation devrait être confiées à un technicien qualifié. L'appareil devrait faire l'objet d'une
inspection par un technicien professionnel avant d'être utilisé et au moins une fois l'an par la suite. Des nettoyages plus
fréquents peuvent être nécessaires si les tapis, la literie, et cetera produisent une quantité importante de pous-sière. Il est
essentiel que les compartiments abritant les commandes, les brûleurs et les conduits de circulation d'air de l'appareil soient
tenus propres.
Secure Vent Direct-Vent System Components,
®
Secure Flex Flexible Vent Components, and
®
Z-FLEX Model GA Venting Systems listed to UL1777 and ULCS635 manufactured by Flexmaster Canada Limited.
®
General Information
900994-00K, 07/2021