Table of Contents
Advertisement
P/N 900948-00 REV. C 06/2019
Ce manuel est disponible en francais, simplement
en faire la demande. Numéro de la pièce 900948-02
P900948-00
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future
reference.
This appliance may be installed in an aftermarket permanently located, manufactured home (USA only)
or mobile home, where not prohibited by local codes. This appliance is only for use with the type of gas
indicated on the rating plate. This appliance is not convertible for use with other gases, unless a certified kit
is used.
Cet appareil peut installé dans une maison préfabriquée (mobile) déjà installée à demeure, si les réglements
locaux le permettent. Ce appareil doit être utilisé uniquement avec le type de gaz indiqué sure la plaque
signalétique. Cet appareil ne peut être converti à d'autres gaz, sauf si une trousse de conversion est utilsée.
WARNING:
FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly could
result in serious injury, death, or property damage.
- Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.
- WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use
any phone in your building.
• Leave the building immediately.
• Immediately call your gas supplier from a neigh-
bor's phone. Follow the gas supplier's instruc-
tions.
• If you cannot reach your gas supplier, call the
fire department.
- Installation and service must be performed by
a qualified installer, service agency or the gas
supplier.
Installation and Operation Instructions
DRT2000-C Series Direct-Vent Gas Fireplaces
Models
DRT2035REN-C
C
US
DRT2035REP-C
DRT2035RMN-C
Report No. F13-094
DRT2035RMP-C
Installateur : Laissez cette notice avec l'appareil.
Consommateur : Conservez cette notice pour
consultation ultérieure.
DRT2035TEN-C
DRT2040REN-C
DRT2035TEP-C
DRT2040REP-C
DRT2035TMN-C
DRT2040RMN-C
DRT2035TMP-C
DRT2040RMP-C
AVERTISSEMENT:
RISQUED'INDENDIE OU D'EXPLOSION
Le non-respect Des avertissements de sécurité
pourrait d'entraîner des blessures graves, la mort
ou des dommages matériels.
- Ne pas entreposer ni utilizer d'essence ni d'autres
vapeurs ou liquides inflammables dans le voisinage
de cet appareil ou de tout autre appareil.
- QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ:
• Ne pas tenter d'allumer d'appareil.
• Ne touchez à aucan interrupteur. Ne pas vous servir
des téléphones se trouvant dans le bâtiment où
vous trouvez.
• Sortez immédiatement de bâtiment.
• Appelez immédiatement votre fournisseur de
gaz depuis un voisin. Suivez les instructions du
fournisseur.
• Si vous ne pouvez rejoindre le fournisseur de gaz,
appelez le service des incindies.
- L'installation et l'entretien doivent être assurés par
un installateur ou un service d'entretien qualifié
ou par le fournisseur de gaz.
DRT2040TEN-C
DRT2045DEN-C
DRT2040TEP-C
DRT2045DEP-C
DRT2040TMN-C
DRT2045DMN-C
DRT2040TMP-C
DRT2045DMP-C
Advertisement
Table of Contents
Related Manuals for Superior Fireplaces DRT2000-C Series
Summary of Contents for Superior Fireplaces DRT2000-C Series
- Page 1 Installation and Operation Instructions DRT2000-C Series Direct-Vent Gas Fireplaces P/N 900948-00 REV. C 06/2019 Models DRT2035REN-C DRT2035TEN-C DRT2040REN-C DRT2040TEN-C DRT2045DEN-C Ce manuel est disponible en francais, simplement en faire la demande. Numéro de la pièce 900948-02 DRT2035REP-C DRT2035TEP-C DRT2040REP-C DRT2040TEP-C...
-
Page 2: Safety And Your Fireplace
Innovative Hearth Products General Information DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 SAFETY AND YOUR FIREPLACE See attached color flyer for proper color representation DANGER HOT GLASS WILL CAUSE BURNS. DO NOT TOUCH GLASS UNTIL COOLED. NEVER ALLOW CHILDREN TO TOUCH GLASS. - Page 3 Innovative Hearth Products General Information DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 La sécurité et Safety and Your Seguridad y su votre foyer Fireplace chimenea All parts of your ¡Todas las partes de la Toutes les parties de votre IHP fireplace get...
-
Page 4: Table Of Contents
Innovative Hearth Products General Information DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 35” Log Set 40” / 45” Log Set THANK YOU FOR YOUR PURCHASE. WE APPRECIATE YOUR BUSINESS! Please carefully read and follow all instructions in this manual. Pay special attention to all warnings and safety information. Following these safety, care, and operation instructions will help ensure many years of dependable and enjoyable service from your fireplace. -
Page 5: Important Safety Information
Innovative Hearth Products General Information DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 IMPORTANT SAFETY INFORMATION Important Safety Informa- L’information de sûreté Información importante de tion importante seguridad 1. WARNING: Do not operate appliance 1. AVERTISSEMENT. Ne pas utiliser l’appareil 1. ADVERTENCIA: No opere el artefacto con el with the glass front removed, cracked si le panneau frontal en verre n’est pas en... -
Page 6: Fireplace Installation, Operation, And Maintenance Notices
Innovative Hearth Products General Information DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 APPLIANCE INSTALLATION, SERVICE, AND MAINTENANCE NOTICES WARNING Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Refer to this manual. For assistance or additional information consult a qualified installer, service agency or the gas supplier. - Page 7 Innovative Hearth Products General Information DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 APPLIANCE OPERATION NOTICES These fireplaces are vented gas appliances. Do not burn wood or other material in these appliances. These appliances are designed to operate on natural gas or propane gas only. The use of other fuels or combinations of fuels will degrade the performance of this system and may be dangerous.
-
Page 8: Packaging List
Innovative Hearth Products General Information DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 INSTALLATION PACKAGING All models include The assembled vented gas fireplace heater is packaged with: • Literature Kit (bag in bottom compartment containing Installation and Operation Instructions (this manual), Hot Glass Safety Flyer, and Safety-In-Operation Warning Labels) •... -
Page 9: Gas Pressure
Innovative Hearth Products General Information DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 BTU Input Table 1 - Input Rate (BTU/HR), Gas Valves Natural Gas Propane Gas Models High Rate Low Rate High Rate Low Rate 35” Models 17,000 13,000 17,000 13,000 40”... - Page 10 Innovative Hearth Products Installation DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 The appliance and its appliance main gas valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pressures in excess of 1/2 psi (3.5 kPa).
-
Page 11: Requirements For The Commonwealth Of Massachusetts
Innovative Hearth Products Installation DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 COMMONWEALTH OF MASSACHUSETTS REQUIREMENTS These appliances are approved for installation in the US state of Massachusetts if the following additional requirements are met: • Install this appliance in accordance with Massachusetts Rules and Regulations 248 C.M.R. Sections 4.00 through 8.00. -
Page 12: Manufactured Home Requirements
Innovative Hearth Products Installation DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 MANUFACTURED HOME REQUIREMENTS This appliance may be installed in an aftermarket, permanently located, manufactured home (USA only) or mobile home, where not prohibited by local codes. Cet appareil peut être installé dans une maison préfabriquée (mobile) déjà installée à demeure si les règlements locaux le permettent. -
Page 13: Vent Termination Clearances
Innovative Hearth Products Installation DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 VENT TERMINATION CLEARANCES These instructions should be used as a guideline and do not supersede local codes in any way. Install venting with the most restrictive requirements as outlined in these instructions, local codes, these instructions, the current National Fuel Gas Code (ANSI Z223.1/NFPA 54) in the USA or the current standards of CAN/CGA-B149.1 in Canada. - Page 14 Innovative Hearth Products Installation DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 Table 7 - Horizontal vent termination clearances for buildings with combustible and noncumbustible exteriors Inside Corner Outside Corner Recessed Location See Table 6 Fixed Balcony with No Side Wall...
-
Page 15: Minimum Clearances To Combustibles
Innovative Hearth Products Installation DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 MINIMUM CLEARANCES TO COMBUSTIBLES Table 8 - Minimum Clearances * 1-1/2” (38mm) to wrapper Fireplace And Vent Clearances Back *** 0” (0 mm) to Spacers The fireplace is approved with zero clearance to combustible materials 1/2”... -
Page 16: Wall Finishes / Surrounds / Mantels
Innovative Hearth Products Installation DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 Figure 5 - Combustible Side Clearances Figure 6 - Mantel Height At 6” minimum side wall clearance, Mantel depth Top View of a combustible wall 16 (407) Fireplace can project to any length. -
Page 17: Installation Sequence
Innovative Hearth Products Installation DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 INSTALLATION SEQUENCE The typical sequence of installation is outlined below; however, each installation is unique and may result in variations to the steps described. See the pages referenced in the following steps for detailed instructions. - Page 18 Innovative Hearth Products Installation DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 Table 10 - Fireplace Framing Specifications Model Framing NOTE: Dimension “D” is the construction to be 10-1/2 required framing depth when 35-7/8 36-1/4 38-3/4 18-1/2 23-3/8 2 x 4, or larger.
-
Page 19: Prepare The Fireplace Top Spacers
Innovative Hearth Products Installation DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 Prepare the Fireplace Top Spacers 1. The two (2) 4” standoff spacers on top of the fireplace cabinet are shipped flat. Remove the screw adjacent to the detached end (Figure 7A). -
Page 20: Determine Vent Setup In The Combination Venting Unit
Innovative Hearth Products Installation DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 (for 45” models only) Determining Vent Setup in the Combination Venting Unit Combination venting units are shipped with round outer flue covers and inner flue cover plates installed that will require removal before connecting the vent pipe. If you require a rear vented unit, remove the round outer rear flue cover (2 screws, Figure 9A) and the inner flue cover plate (4 screws, Figure 9B). -
Page 21: Rough In The Electrical Supply, If Needed
Innovative Hearth Products Installation DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 Rough in the Electrical Supply, if Needed As necessary, rough in the fireplace electrical supply per NEC and local codes. Place the Fireplace in the Framing and Secure NOTE: Nailing flanges, combustible members, and screw heads in areas directly adjacent to the nailing flanges are EXEMPT from the 1/2”... -
Page 22: Install The Vent Restrictor (If Necessary)
Innovative Hearth Products Installation DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 Install the Vent Restrictor (if necessary) 1. Use the vent run descriptions in Figure 11 to determine if a vent restrictor is necessary. U-Shaped Vent 2. If necessary, assemble the vent restrictor and wing as detailed in Figures 11 and 14. - Page 23 Innovative Hearth Products Installation DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 Connecting the Vent Pipe Secure Vent SV4.5 direct-vent system components are unitized concentric pipe components featuring positive twist ® lock connections (Figures 15 - 16, Page 23). All of the fireplaces covered in this document are fitted with collars having locking inclined channels.
- Page 24 Innovative Hearth Products Installation DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 Vent section length table Table 14 will assist calculating how many vent sections are needed for the planned vent configuration. When a vent section is engaged with another section, its effective length will be 1-1/2” shorter.
-
Page 25: Install The Vent System
Innovative Hearth Products Installation DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 Clearance to combustibles Maintain the minimum clearance to combustibles (e.g., framing, • 1” (26 mm) from all sides attic, ceiling insulation, etc.). For all vertical runs: NOTE: Attic insulation shield (H3907, see Page 48) must be •... - Page 26 Innovative Hearth Products Installation DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 Vertical (Offset) Installation 1. Analyze the vent route and determine the number of vent sections and elbows required—See Effective Vent Length on Pages 23-24 for more information. Plan the venting so that a joint does not occur in the ceiling or roof joists.
- Page 27 Innovative Hearth Products Installation DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 7. Change vent direction of horizontal/inclined run—Install the SV4.5E45 and SV4.5E90 elbows in the same manner as the straight vent sections. See Vent elbows on Page 23 for more information.
- Page 28 Innovative Hearth Products Installation DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 Vertical Vent Figures/Tables NOTE: Secure Vent rigid vent pipe is shown in the figures; Secure Flex flexible vent pipe may also be used. ® ® NOTE: Rise per foot run ratios are acceptable all the way to level. For best results, maintain the horizontal/inclined run in a straight (no dips), slightly elevated plane of approximately 1/4”...
- Page 29 Innovative Hearth Products Installation DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 Table 17 - Top Vent—Two 90° Elbows Table 18 - Rear Vent—Three Elbows Table 19 - Top Vent—Three Elbows When using Secure Flex , use ® ceiling firestop/ Ceiling firestop/ spacer SF4.5VF.
- Page 30 Innovative Hearth Products Installation DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 Install the Horizontal Termination Vent System These instructions should be used as a guideline and do not supersede local codes in any way. Install venting with the most restrictive requirements as outlined in these instructions, local codes, these instructions, the current National Fuel Gas Code (ANSI-Z223.1) in the...
- Page 31 Innovative Hearth Products Installation DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 8. Change vent direction—At transition from or to a horizontal/inclined run, install SV4.5E45 or SV4.5E90 elbows in the same manner as the straight vent sections. The elbows feature a twist section to allow them to be routed about the center axis of their initial collar section to align with the required direction of the next vent run element.
- Page 32 Innovative Hearth Products Installation DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 Figure 25 - Installing the Horizontal Termination Installing the Horizontal Termination, SV4.5HT-2 To help minimize water infiltration Firestop/Spacer (SV4.5HF) shown Typical (all models) or SV4.5HTSS (35” models only) it is recommended that the Fire- Termination on the exterior side of the wall.
- Page 33 Innovative Hearth Products Installation DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 Table 20 - Venting Components Required for Various Exterior Wall Thicknesses, when using Typical Termination Kits Vent Components Required Exterior Wall Thickness Termination Kit Only 6 to 9-1/4” (152 to 235 mm) Termination Kit and 6”...
- Page 34 Innovative Hearth Products Installation DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 Table 23 - Top Vent—One 90° Elbow, Elbow Connection NOT at Fireplace H Maximum V Minimum feet meters feet meters 1.524 0.305 3.048 0.610 4.572 0.914 When using Secure Flex, use Firestop/Spacer 7.62...
- Page 35 Innovative Hearth Products Installation DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 Table 26 - Rear Vent—Three 90° Elbows H + H Maximum H Maximum V Minimum feet meters feet meters feet meters Wall firestop/spacer 1.524 0.610 0.305 Wall Firestop/Spacer SV4.5HF ** SV4.5HF**...
- Page 36 Innovative Hearth Products Installation DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 Vertical or Horizontal Venting Using Secure Flex Kits and Components ® When Secure Flex kits are used in a rear flue, horizontal termination installation, at least 1 ft of vertical rise is required.
-
Page 37: Complete The Field Wiring
Innovative Hearth Products Installation DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 f. Install three (3) sheet metal screws 120° apart through the flexible vent and into the adaptor collar just below the gear clamp to provide additional security to the connection. - Page 38 Innovative Hearth Products Installation DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 1. If installing an ON/OFF wall switch or thermostat, mount it in a convenient location on a wall near the fireplace. 2. Wire the control switch within the millivolt control circuit using the 15 ft of 2-conductor wire supplied with the unit (Figure 31).
-
Page 39: Connect The Gas Line
Innovative Hearth Products Installation DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 See the Operation section on Page 51 for more details. NOTE: Electronic models must be connected to the main power supply. 1. Route a 3-wire, 120 Vac, 60 Hz, 1 ph power supply to the fireplace junction box. - Page 40 Innovative Hearth Products Installation DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 Connect the Gas Line All codes require a shutoff valve mounted in the supply line. Figure 31 illustrates two methods for connecting the gas supply. The flex-line method is acceptable in the U.S., however, Canadian requirements vary depending on locality.
-
Page 41: Verify Proper Fireplace Operation
Innovative Hearth Products Installation DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 Test Factory and Field Connections for Gas Leaks WARNING Never use an open flame to check for leaks. Turn on gas supply and test for gas leaks, using a gas leak test solution—also known as bubble leak solution. -
Page 42: Install The Logs, And Glowing Embers Media
Innovative Hearth Products Installation DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 Install the Firebox Liners (Optional Kits) 1. Install the Firebox Liners (see Page 54). Install the Logs, and Glowing Embers 1. See Pages 56 - 62 for instructions on Installing the logs, and glowing embers. - Page 43 Innovative Hearth Products Installation DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 Figure 33 - Air Shutter Adjustment Rod Table 28 - Air Shutter Adjustment Guidelines Adjustment Amount of Primary Air Flame Color Air Shutter Adjustment Set-Screw If air shutter is...
-
Page 44: Install The Hood
Innovative Hearth Products Installation DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 Install the Hood after fireplace is cool NOTE: All models must have a hood installed prior to operation. NOTE: Hood is slotted and has some adjustment. It is suggested that the center screw should be installed first and the ends last. -
Page 45: Barrier Replacement
Innovative Hearth Products Installation DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 BARRIER INSTALLATION FOR D2000C SERIES Installation (see Figures 36A and 36B) 1. Slide barrier into upper trim panel. NOTE: This panel will rotate for ease of installation. Figure 36A - Slide Barrier into Upper Trim Panel... -
Page 46: Install The Finishing Materials
Innovative Hearth Products Installation DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 Figure 37 - Combustible Wall Framing Install the Finishing Materials 1. Complete finished interior wall. NOTE: To install the fireplace facing flush with the finished This Area Must Remain Clear... - Page 47 Innovative Hearth Products Installation DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 INSTALLER - ATTACHING SAFETY-IN-OPERATION WARNINGS It is the installers responsibility to ensure these warnings are properly affixed during installation. These warning labels are a critical step in informing consumers of safe operation of this appliance.
-
Page 48: Installation Accessories
Innovative Hearth Products Installation DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 INSTALLATION ACCESSORIES IMPORTANT NOTE: The installation accessories shown in this section are part of the safety agency listing for the product models represented in this manual. Listed Secure Vent Components ®... - Page 49 Innovative Hearth Products Installation DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 Listed Secure Vent Components ® Cat. No. Model Description Cat. No. Model Description 96K93 SV4.5SU Support Strap 77L76 SV4.5E45 45° Elbow, Corrugated Horizontal Riser Kit, 14”(see 99L02 SV4.5HRK14 750146M) Horizontal Riser Kit, 36”...
-
Page 50: Gas Conversion Kits
Innovative Hearth Products Installation DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 GAS CONVERSION KITS WARNING This conversion kit shall be installed by a qualified service agency in accordance with the manufacturer’s instructions and all applicable codes and requirements of the authority having jurisdiction. If the information in these instructions is not followed exactly, a fire, explosion, or the production of carbon monoxide may result;... -
Page 51: Operation
Innovative Hearth Products Operation DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 OPERATION WARNING Young children should be carefully supervised when they are in the same room as the appliance. Toddlers, young children and others may be susceptible to accidental contact burns. A physical barrier is recommended if there are at risk individuals in the house. - Page 52 Innovative Hearth Products Operation DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 HOMEOWNER’S INSTRUCTIONS - ATTACHING SAFETY IN OPERATION WARNINGS ATTACHING SAFETY IN OPERATION WARNINGS APPOSITION DES MISES EN GARDE RELATIVES COLOCACIÓN DE ADVERTENCIAS DE SEGURIDAD À LA SÉCURITÉ D’UTILISATION EN OPERACIÓN...
-
Page 53: Accessing Control Compartment
Innovative Hearth Products Operation DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 Burn-in Period The first few times this fireplace is operated, there will be an odor from the curing of paint and the burning off of the lubricants used in the manufacturing process. Depending on usage, the burn-in period may take a few hours or a few days. -
Page 54: Optional Accessory: Install The Firebox Liners
Innovative Hearth Products Operation DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 Installing the Firebox Liners (Optional Kit) KIT CONTENTS Affected Fireplace Models 1 ea. Set of 4 Hand Bend Brackets 35" , 40" and 45" direct- 1 ea. Set of Optional Fiber Panels vent fireplace models offered with 1 ea. - Page 55 Innovative Hearth Products Operation DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 Bracket Bracket Figure 39C - Insert Bent Bracket Bracket Example of Pre-Bent Bracket Before Insertion Insert Top Leg Of Bracket Between Lintel And Top Panel Bottom Figure 39D Figure 39F - Brackets Installed...
- Page 56 Innovative Hearth Products Operation DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 Install the Logs and Glowing Embers WARNING • Turn OFF all gas and electricity to the appliance before installing the embers, and logs. • Do NOT install the logs until the appliance has been completely installed, the gas line connected and tested for leaks, and the initial burner operation has been confirmed.
- Page 57 Innovative Hearth Products Operation DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 Installing the DRT2000-C 35 Series Log Set The logs have notches/tabs to assist proper positioning. Upper logs rest on lower logs via notches/tabs. Proper log placement is critical to prevent sooting. Place the logs in the gaps between flame peaks, so they do not impinge the flames. Follow the log placement instructions precisely.
- Page 58 Innovative Hearth Products Operation DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 Installing the DRT2000-C 35 Series Log Set (continued) 6. Install back right log (4) (Figure 44). This log should be moved as far to the right as possible after installation on tab.
- Page 59 Innovative Hearth Products Operation DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 Installing the DRT2000-C 40 Series Log Set The logs have notches/tabs to assist proper positioning. Upper logs rest on lower logs via notches/tabs. Proper log placement is critical to prevent sooting. Place the logs in the gaps between flame peaks, so they do not impinge the flames. Follow the log placement instructions precisely.
- Page 60 Innovative Hearth Products Operation DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 Installing the DRT2000-C 40 Series Log Set (continued) 6. Install back right log (4) (Figure 51). 7. Tear the glowing embers into dime size pieces. Place glowing embers as shown in Figure 53.
- Page 61 Innovative Hearth Products Operation DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 Installing the DRT2000-C 45 Series Log Set The logs have notches/tabs to assist proper positioning. Upper logs rest on lower logs via notches/tabs. Proper log placement is critical to prevent sooting. Place the logs in the gaps between flame peaks, so they do not impinge the flames. Follow the log placement instructions precisely.
- Page 62 Innovative Hearth Products Operation DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 Installing the DRT2000-C 45 Series Log Set (continued) 6. Install back right log (4) (Figure 58). 7. Tear the glowing embers into dime size pieces. Place glowing embers as shown in Figure 60.
- Page 63 Innovative Hearth Products Operation DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 Installing and removing the glass door WARNING • Do not attempt to substitute the materials used on these doors, or replace cracked or broken glass. • Handle this glass with extreme care! Glass is susceptible to damage—Do not scratch or handle roughly while reinstalling the glass door frame.
- Page 64 Figure 62 - Barrier NOTICE: All DRT2000-C series fireplaces require a 35” Barrier - Cat. No. F1839 barrier (provided) to reduce the risk of burns from the hot viewing glass.
-
Page 65: Maintenance
Innovative Hearth Products Operation DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 MAINTENANCE Refer to the Maintenance Schedule on Page 67 for maintenance tasks, procedures, frequency, and a listing of by whom the tasks should be performed. Always verify proper fireplace operation after servicing. - Page 66 Innovative Hearth Products Operation DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 Inspecting the glass gasket Visually inspect the gasket on the backside of the glass door. The gasket surface must be clean, free of irregularities, and seated firmly. Cleaning the control compartment Keep the control compartment clean by vacuuming or brushing it out at least twice a year.
- Page 67 Innovative Hearth Products Operation DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 MAINTENANCE SCHEDULE See the tables below for detailed information about required maintenance, both regular and annual. Maintenance Performed Annually—Before the Burning Season Maintenance Task Performed By Procedure Inspecting/Cleaning Burner, Logs, and...
-
Page 68: Accessory Components
Innovative Hearth Products Operation DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 ACCESSORY COMPONENTS Firebox Liner Kits Termination Shroud (fits H1968) Bag of Glowing Embers Replacement ember materials are available for use with these appliances. Order kits as part of the periodic maintenance of the Blackstone appliance. - Page 69 Innovative Hearth Products Operation DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 Cost Effective Solution Unit-Mountable Rocker Switch Kit Thermostatic or Manual modes • Simple On/Off operation This rocker switch kit can be installed directly • LCD Display • Works with millivolt and low voltage electronic in the control compartment to provide ON/OFF •...
- Page 70 Innovative Hearth Products Operation DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 NOTES ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________...
-
Page 71: Lighting Instructions
Innovative Hearth Products Operation DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 LIGHTING INSTRUCTIONS, MILLIVOLT - ENGLISH FOR YOUR SAFETY READ BEFORE LIGHTING WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. - Page 72 Innovative Hearth Products Operation DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 LIGHTING INSTRUCTIONS, MILLIVOLT - FRENCH POUR PLUS DE SÉCURITÉ, LIRE AVANT D’ALLUMER AVERTISSEMENT. Quiconque ne respecte pas à la lettre les instructions dans la présente notice risque de déclencher un incendie ou une explosion entraînant des dommages, des blessures ou la mort.
- Page 73 Innovative Hearth Products Operation DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 LIGHTING INSTRUCTIONS, ELECTRONIC - ENGLISH FOR YOUR SAFETY READ BEFORE OPERATING WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life.
- Page 74 Innovative Hearth Products Operation DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 LIGHTING INSTRUCTIONS, ELECTRONIC - FRENCH POUR PLUS DE SÉCURITÉ LIRE AVANT DE METTRE EN MARCHE AVERTISSEMENT. Quiconque ne respecte pas à la lettre les instructions dans la présente notice risque de déclencher un incendie ou une explosion entraînant des dommages, des blessures ou la mort.
-
Page 75: Troubleshooting
Innovative Hearth Products Operation DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 TROUBLESHOOTING Before troubleshooting, ensure that the fireplace main line gas shutoff valve and the wall switch are in the ON position. The following troubleshoots the fireplace only to an elementary level. For detailed remote and ignition system troubleshooting, refer to the instructions provided with the remote. -
Page 76: Replacement Parts
Innovative Hearth Products Operation DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 REPLACEMENT PARTS Cat. No. Fireplace Models Description Cat. No. Fireplace Models Description F3877 DRT2035REN-C 35” DV,Rear, Elec, F3883 DRT2040RMN-C 40” DV,Rear, MV F3878 DRT2035REP-C 35” DV,Rear, Elec F3884 DRT2040RMP-C 40”... - Page 77 Innovative Hearth Products Operation DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 35” Models 40” Models 45” Models REPLACEMENT PARTS (continued) Cat. No. Cat. No. Cat. No. Millivolt Parts --- Millivolt Pilot Assembly, Natural Gas 69L17 69L17 69L17 --- Millivolt Pilot Assembly, Liquid Propane...
- Page 78 Innovative Hearth Products Operation DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 NOTES ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________ ______________________________________________________...
-
Page 79: Warranty
Innovative Hearth Products Superior Brand Gas Fireplaces, Stoves and Inserts ® 20 Year Limited Warranty THE WARRANTY Innovative Hearth Products ("IHP") 20 Year Limited Warranty warrants your Superior Brand gas fireplace, Stove or Insert ("Product") to be free from defects in materials ®... - Page 80 Innovative Hearth Products Installation and Operation Instructions DRT2000-C Series Direct-Vent Gas Fireplaces 900948-00C, 06/2019 SuperiorFireplaces.us.com Record the following important information about your fireplace: Fireplace model number Fireplace serial number Date fireplace was Installed Type of gas fireplace uses Dealer name...