1. Manuals
  2. Brands
  3. Graco Manuals
  4. Industrial Equipment
  5. VRM 24F872
  6. Instructions manual

Graco VRM 24F872 Instructions Manual

Hydraulic, plural-component, variable-ratio proportioner
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Instructions
™
VRM
Hydraulic, Plural-Component, Variable-Ratio Proportioner.
For pouring and dispensing sealants and adhesives. For professional use only.
Not approved for use in European explosive atmosphere locations.
Important Safety Instructions
Read all warnings and instructions in this
manual. Save these instructions.
See page 4 for model information, including max-
imum working pressure and approvals.
313873J
EN
ti17663a

Advertisement

Table of Contents
loading

Related Manuals for Graco VRM 24F872

Summary of Contents for Graco VRM 24F872

  • Page 1 Instructions ™ 313873J Hydraulic, Plural-Component, Variable-Ratio Proportioner. For pouring and dispensing sealants and adhesives. For professional use only. Not approved for use in European explosive atmosphere locations. Important Safety Instructions Read all warnings and instructions in this manual. Save these instructions. See page 4 for model information, including max- imum working pressure and approvals.

  • Page 2: Table Of Contents

    Dispensing ......38 Graco Standard Warranty ....87 100:XX Ratio Output Feature .

  • Page 3: Related Manuals

    Related Manuals Related Manuals Manuals are available at www.graco.com. Component manuals in English: System Manuals 313874 VRM Repair-Parts Power Distribution Box Manual 3A0239 Power Distribution Boxes Instruc- tions-Parts Pumpline Manuals 3A0022 ™ U-Cup Dura-Flo Lowers 3A0021 Vertical Hydraulic Driver Repair-Parts...

  • Page 4: Models

    Models Models Full Load Approximate Peak Max Flow Output per Hydraulic Maximum Fluid Amps Per Voltage System Rate** Cycle (A+B)** Pressure Working Pressure ‡ System approved Phase* (phase) Watts† lb/min (kg/min) gal. (liter) Ratio** psi (MPa, bar) 24F872 60 A 230 (3) 24F391 55 A...

  • Page 5: Warnings

    Warnings Warnings The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclama- tion point symbol alerts you to a general warning and the hazard symbol refers to procedure-specific risk. Refer back to these warnings. Additional, product-specific warnings may be found throughout the body of this manual where applicable.
  • Page 6 Warnings WARNING FIRE AND EXPLOSION HAZARD Flammable fumes, such as solvent and paint fumes, in work area can ignite or explode. To help pre- vent fire and explosion: • Use equipment only in well ventilated area. • Eliminate all ignition sources; such as pilot lights, cigarettes, portable electric lamps, and plastic drop cloths (potential static arc).
  • Page 7 Warnings WARNING MOVING PARTS HAZARD Moving parts can pinch, cut or amputate fingers and other body parts. • Keep clear of moving parts. • Do not operate equipment with protective guards or covers removed. • Pressurized equipment can start without warning. Before checking, moving, or servicing equip- ment, follow the Pressure Relief Procedure and disconnect all power sources.

  • Page 8: Important Two-Component Material Information

    Important Two-Component Material Information Important Two-Component Material Information Isocyanate Conditions Moisture Sensitivity of Isocyanates Isocyanates (ISO) are catalysts used in two component foam and polyurea coatings. ISO will react with moisture Spraying or dispensing materials containing isocya- (such as humidity) to form small, hard, abrasive crystals, nates creates potentially harmful mists, vapors, and which become suspended in the fluid.

  • Page 9: Changing Materials

    A (Red) and B (Blue) Components Changing Materials • When changing materials, flush the equipment mul- tiple times to ensure it is thoroughly clean. • Always clean the fluid inlet strainers after flushing. • Check with your material manufacturer for chemical compatibility.

  • Page 10: Component Identification

    Component Identification Component Identification AA Advanced Display Module (see page 16) AJ Pump Wet Cup AB Hydraulic Power Pack AK Main Power Switch AC Vertical Hydraulic Driver AL Air Supply Inlet AD Pump Lower AM Electrical Enclosure AE Flow Meter AN Ratio Check Dispense Valves/Ports AF Power Distribution Box AP Material Line...
  • Page 11 Component Identification ti17664a . 2: Component Identification 313873J...
  • Page 12 Component Identification Circuit Breakers Most circuit breakers are located inside the power distri- bution box. The main block of circuit breakers in the power distribution box is shown below, with detailed information in the following table. See the power distri- bution box manual for more information.

  • Page 13: Hydraulic Power Pack

    Component Identification Hydraulic Power Pack 257442_313873-5_1t 257442_313873-5_2t Shown with shroud removed Key: 8 Gallon Hydraulic Oil Reservoir (see Technical Data on Motor Control Module (see page 14) page 86 for specifications) Electric Motor Hydraulic Oil Filter Dipstick Hydraulic Fluid Drain Port Hydraulic Housing 313873J...

  • Page 14: Motor Control Module (Mcm)

    Component Identification Motor Control Module (MCM) The MCM is located in the Hydraulic Power Pack. NOTICE If the Motor Control Module is replaced, the selec- When installed, the end of the MCM with the power tor switch must be set prior to initial startup of the input connection (12) faces down and the end with the Motor Control Module or damage may occur.
  • Page 15 Component Identification Description Access Cover Module Status LEDs Warning Label A (Red) MCM only: ADM, Power Distribution Box 1A, 1B B (Blue) MCM only: FCM, Power Distribution Box NOTE: 1A and 1B are interchangeable. Three-way Splitter to: Oil Low Level Sensor, Dispense Valve Solenoid, Footswitch Oil Temperature Sensor...

  • Page 16: Advanced Display Module (Adm)

    Component Identification Advanced Display Module (ADM) User Interface TI12362a1 . 5: ADM Component Identification - Front Buttons Call Call Button Function Button Function Softkeys Defined by icon next to softkey Enable/disable ADM Enable/ Abort Abort current operation Disable Enter Accept change, acknowledge error, System Displays system status select item, toggle selected item...
  • Page 17 Component Identification ti12902a . 6: ADM Component Identification - Rear Key: Flat Panel Mount Module Status LEDs Model Number Identification Label Accessory Cable Connection USB Interface (see Appendix E - USB Operation Software Token Access Cover beginning on page 80) Battery Access Cover CAN Cable Connection to MCM See ADM Troubleshooting on page 52 for LED status information.
  • Page 18 Component Identification ADM Screen Components See the ADM appendix sections beginning with Appendix A - ADM Icons Overview on page 57 for more informa- tion. Current date and time Previous screen Current screen Next screen Operating Mode Faults, Status Enter/Exit screen Previous screen no.

  • Page 19: Fluid Control Module (Fcm)

    Component Identification Fluid Control Module (FCM) The fluid control module is located inside the electrical enclosure. ti12337a1 ti12336a1 . 9: Key: Module Connection Screws Access Cover Module Status LEDs CAN Connectors (one is connected to MCM, other is unused) 313873J...

  • Page 20: Setup

    Setup Setup Initial Machine Setup Electrical Cord Requirements NOTE: Power cord is not supplied. See the following Perform this setup procedure to prepare the machine for table. initial operation. Table 1: Power Cord Requirements Cord Requirements Model AWG (mm The machine is not properly grounded until this setup procedure is performed.
  • Page 21 Setup Power Line Voltage Surges The chart below shows the permissible magnitude and duration of temporary over-voltage events: Power conversion equipment can be sensitive to voltage fluctuations on incoming power. The Motor Control Mod- ule falls under the category of power conversion equip- Maximum Permissible Transient Voltage Surges * Constructed from ITIC 1996 curve, referenced by IEC 61000-2-4 ment because energy is stored on a capacitive bus and...
  • Page 22 Setup 4. Install feed system. Check hydraulic fluid levels. NOTE: This step only connects the feed system. Do not The hydraulic reservoirs are filled at the factory. See allow fluid to flow into the system in this step. Technical Data on page 86 for hydraulic fluid specifica- tions.
  • Page 23 Setup d. Navigate to System #1 screen then define con- trol mode, dispense mode, and pump informa- tion. See page 61. e. Navigate to System #2 screen then define dis- pense valve details and other system settings. See page 61. Navigate to System #3 screen then define labels, pressure imbalance, and flow meter details.

  • Page 24: Startup

    Startup Startup 1. Perform all required maintenance tasks. See Main- tenance on page 46. 2. Check for leaks. 3. Check hydraulic fluid levels. 4. Check pump wet cup fluid levels. 5. Check feed system fluid levels. 6. Turn Main Power Switch to the ON position. The splash screen will be displayed on the ADM until it is finished loading.

  • Page 25: Priming

    Priming Priming 1. Place waste containers below both ratio check dis- 7. Continue dispensing until clean, air-free material is pense valves. dispensed from both sides then press to stop NOTE: Both ratio check dispense valves will be open dispensing. when dispensing in Prime Mode. Only one pump moves but material may drip from the other ratio check dis- 8.

  • Page 26: Operation

    Operation Operation ADM Operation Overview ADM Navigation Diagram Run Screens Optional: Home Errors #1 Events #1 Maintenance Diagnostic Errors #2 Events #2 Errors #... Events #... Password Entry (if enabled) Setup Screens Calibration Shot #1 Sequences #1 System #1 Maintenance Supply Conditioning #1 Advanced #1...
  • Page 27 Operation Navigation Overview Change ADM Values For all ADM screens to be accessible and functional, the To edit information in a screen, such as a shot definition ADM must be enabled and an operating mode other or a system setting like time or date format, follow this than Standby or Disabled must be selected.

  • Page 28: Machine Operation Overview

    As the system warms up and material thickness decreases, the Graco suggests to discard all material dispensed during ramp up feature will increase the flow rate until the a “Learning New Set Point” dispense.

  • Page 29: System Setup And Calibration

    Operation System Setup and Calibration 7. Navigate to the System 2 screen. Perform this entire procedure if any of the following con- ditions are met: • The machine is new • One or both materials in the system have changed since last performing this procedure •...
  • Page 30 Operation 12. Select the flow meter types installed on your sys- tem. Most systems use “HG6000” flow meters for 16. Press both sides. If no flow meters are installed, select the “Disable” option as indicated below and proceed to step 14. 17.
  • Page 31 Operation b. Place a waste container below the ratio check Flow Rate and Ratio Learning valves. The next steps will cause the machine 25. At the main Calibration screen, press to erase to dispense material. all learned data. c. Press then .
  • Page 32 Operation 29. On the main run screen, verify the ratio check valve NOTE: Continue base purge until clean material comes out of the end of the mixer. button is not active. d. When all mixed material is pushed out of the mixer, press to stop dispensing.
  • Page 33 Operation 41. Weigh the two buckets and use the net weight of each dispensed material to calculate the actual ratio of the dispensed material. 42. If the calculated ratio of the weighed materials does not match the ratios displayed on the ADM, go to step 1 to re-calibrate the flow meters.
  • Page 34 Operation Flow Meter or Flow/Ratio Calibration NOTE: After the weights are entered the K-factor will be shown to the right of the weights. The previous K-factor is shown to the left of the weight entry fields. 1. At the main Calibration screen, press to erase any previously learned flow meter calibration data.
  • Page 35 Operation No Flow Meter Machine Calibration 3. Press to exit the setup screen and verify the It is highly recommended that the user operate the ratio check option is not selected. machine in weight mode when flow meters are not installed or have been disabled.
  • Page 36 Operation 7. Place waste containers below the ratio check noz- NOTE: After entering the net weight of B (Blue) material, zles and start a ratio check dispense. Adjust the the ADM will inform the user how close the respective ratio check opening screws until the pressures dis- flow of the pump was to the desire rate.
  • Page 37 Entry” option in the Advanced #3 screen. The user can verify the machine calibration by performing a ratio check dispense and weighing the A (Red) and B (Blue) materials. NOTE: Graco suggests to discard all material dispensed during a “Learning New Set Point” dispense. 313873J...

  • Page 38: Dispensing

    Operation Dispensing Dispense in Sequence Mode Sequences can be defined on the Sequences screen. Sequences are defined on the Sequences screen, see Dispense in Shot Mode page 60. To dispense in Shot mode, at least one shot number must be defined. Shots are defined on the Shots 1.
  • Page 39 Operation Dispense in Operator Mode 7. Check the ADM for errors and pop-up notifications that could indicate a faulty dispense. Press acknowledge any displayed errors. Operator Mode begins dispensing when is pressed and stops when it is pressed again. NOTE: If a footswitch is used, press and hold to dis- pense.

  • Page 40: 100:Xx Ratio Output Feature

    Operation 100:XX Ratio Output Feature The user now has the capability to enter, edit and dis- play ratios in 100 to XX format, rather than the standard XX to 1 format. For instance, when operating in the default XX:1 format, a typical run screen may appear like the following: As indicated above, both the ratio set point (bottom right), and actual ratio dispensed (top middle) are output...

  • Page 41: 100:Xx Ratio Tolerance Entry

    Operation So in XX:1 ratio forma5t, with a ratio set point of 4.0:1, ratio greater 4.08 to 1 and less than 3.92 to 1 will gener- ate an off deviation alarm, and ratios greater than 4.16 to 1 and less than 3.84 to 1 will generate an off ratio alarm.

  • Page 42: Off Ratio Time To Fault Entry

    Operation Off Ratio Time to Fault Entry The user can now navigate to this field, enter any num- ber from 0 (default value, indicating the override feature if off) to 30 seconds. If the “Off Ratio Fault Time Over- The VRM and VPM system now allows the user to enter ride”...

  • Page 43: Flushing

    Flushing Flushing 9. To maintain grounding continuity when flushing or relieving pressure, hold a metal part of dispense valve firmly to the side of a grounded metal pail, then press . Continue to dispense until the sys- tem is thoroughly flushed then press to stop Flush equipment only in a well-ventilated area.

  • Page 44: Shutdown

    Shutdown Shutdown Short-term 7. Place container under the mixer and allow mixer to drain completely. 1. Place container under mixer. NOTICE 2. If using a moisture-sensitive material, park pumps. Preventing material from draining from the mixer may cause material in the mixer to harden and a.

  • Page 45: Pressure Relief Procedure

    Pressure Relief Procedure Pressure Relief Procedure 1. Perform Shutdown procedure. 2. Place a waste container below each ratio check valve. In the following step, any pressure in the lines will be instantly relieved which may lead to material spraying out of the valve and splashing in the bucket. Use appropriate protective wear to prevent contact with materials.

  • Page 46: Maintenance

    Maintenance Maintenance Change Hydraulic Oil and Filter Change break-in oil in a new unit after the first 250 hours of operation or within 3 months, whichever comes first. After initial break-in, see the following table for rec- Check all sub-component manuals for maintenance ommended oil and filter change schedule.

  • Page 47: Install Upgrade Tokens

    To install software upgrades: Replace Battery 1. Use correct software token stated in the table. See A lithium battery maintains the ADM clock when power ™ Graco Control Architecture Module Programming is not connected. manual for instructions. To replace the battery:...

  • Page 48: Motor Control Module (Mcm)

    Maintenance Motor Control Module (MCM) Keep heat sink fins clean at all times. Clean them using compressed air. NOTE: Do not use conductive cleaning solvents on the module. Heat Sink Fins r_257396_3b9905_02b . 12: Clean Heat Sink Fins Install Upgrade Token See Install Upgrade Tokens on page 47.
  • Page 49 Maintenance 313873J...

  • Page 50: Troubleshooting

    Troubleshooting Troubleshooting Light Tower (Optional) Signal Description Green on only System is powered up and there are For information about ADM error and event codes see no error conditions present Appendix D - ADM Event and Error Codes Overview, Yellow on An advisory exists page 69.
  • Page 51 Troubleshooting Problem Cause Solution Material imbalance Inadequate flow from pump; cavitation Clean inlet strainer screen Worn pump inlet valve ball/seat or gasket, repair as necessary Erratic pump movement Pump cavitation Feed pump pressure is too low, adjust pressure to within required range Pump output low Obstructed fluid hose or mixer;...

  • Page 52: Adm Troubleshooting

    Troubleshooting ADM Troubleshooting ti12902a ti12362a1 . 13: ADM Component Identification - Rear ADM System Status LEDs (B) Conditions Module Status LED Signal Description Green on Run mode, System on Green flashing Setup mode, System on Yellow on Run Mode, System off ADM Module Status LEDs (N) Conditions Module Status LED Signal...

  • Page 53: Motor Control Module

    Troubleshooting Motor Control Module Diagnostic Information Table 3: LED Status Signal Module Status LED Signal Description Green on System is powered up Yellow on Internal communication in progress Red solid MCM hardware failure. Replace MCM Red flashing fast Uploading software Red flashing slow Token error, remove token and upload software token again...
  • Page 54 Troubleshooting Acceptable Size and Duration of Power Line Voltage Fluctuations The Motor Control Module is designed to withstand volt- age fluctuations from the incoming power supply. If the incoming power supply goes outside of the tolerable range, an over-voltage condition is flagged and the sys- tem shuts down in an alarm state.

  • Page 55: Fluid Control Module

    Troubleshooting Fluid Control Module Diagnostic Information Module Status LED Signal Diagnosis Green on System is powered up Yellow Internal communication in progress Red solid FCM hardware failure. Replace FCM. Red flashing fast Uploading software Red flashing slow Token error. Remove token and upload software token again.
  • Page 56 Troubleshooting 313873J...

  • Page 57: Appendix A - Adm Icons Overview

    Appendix A - ADM Icons Overview Appendix A - ADM Icons Overview Setup Screen Icons Icon Description Icon Description Learn Top-Most Piston Position Enter Screen Go to Next Calibration Screen Exit Screen Begin Weight Calibration Shot Erase Selected Item Dispense Valve Details Erase All Items Shown Shot Number Change Multiple Values...

  • Page 58: Home Screen Icons

    Appendix A - ADM Icons Overview Home Screen Icons Icon Description Icon Description Prime A (Red) Side Select Operating Mode Prime B (Blue) Side Initiate Dispense Enter Screen Dispense Disabled Exit Screen Ratio Check Erase Selected Item Park Piston Erase All Items Shown Park Piston Disabled Weight Close Dispense Valve...

  • Page 59: Appendix B - Adm Setup Screens Overview

    Appendix B - ADM Setup Screens Overview Appendix B - ADM Setup Screens Overview Setup Screens Navigation Diagram Calibration Shot #1 Sequences #1 System #1 Maintenance Supply Conditioning #1 Advanced #1 Shot #2 Sequences #2 System #2 Conditioning #2 Advanced #2 Shot #...
  • Page 60 Appendix B - ADM Setup Screens Overview Sequences Calibration - Learn Mode This screen is for learning the mechanical limits for pis- This screen allows the user to edit sequence definitions. ton travel. The contents of this screen change based on the Dis- pense mode.
  • Page 61 Appendix B - ADM Setup Screens Overview System #1 System #2 This screen allows the user to set mechanical system This screen allows the user to set the Gel Timer proper- settings and the Dispense Mode setting. ties and set which items are installed on the machine. Dispense mode can be set to time, volume, or weight.
  • Page 62 Appendix B - ADM Setup Screens Overview System #3 Maintenance This screen allows the user to edit the labels for the A This screen shows shot number and sequence position (Red) and B (Blue) sides of the machine. The labels set counters.
  • Page 63 Appendix B - ADM Setup Screens Overview Conditioning #1 Advanced #1 NOTE: The VRM does not use temperature condition- This screen allows the user to set the language, date ing. Do not check any of the boxes on this screen. format, current date, time, setup screens password, screen saver delay, and turn on or off silent mode.
  • Page 64 Appendix B - ADM Setup Screens Overview Advanced #3 Advanced #4 This screen is for enabling the optional Diagnostic This screen allows the user to control the availability of screen and for enabling USB log downloading and USB some key system features. errors.

  • Page 65: Appendix C - Adm Run Screens Overview

    Appendix C - ADM Run Screens Overview Appendix C - ADM Run Screens Overview Run Screens Navigation Diagram Optional: Home Errors #1 Events #1 Maintenance Diagnostic Errors #2 Events #2 Errors #... Events #... Home Screens Disabled The Home screen is the first screen that displays when the machine is started and when switching from the Setup screens to the Run screens.
  • Page 66 Appendix C - ADM Run Screens Overview Shot Operator This mode allows the user to dispense using one of the This mode allows users to dispense without using pre- defined shots. See Shots screen on page 59. Shot defi- defined shot numbers or sequences. Use to set nition including flow, ratio, progress, and size is shown at the bottom of the screen.
  • Page 67 Appendix C - ADM Run Screens Overview Errors Screen Maintenance The Errors screens display the 50 most recent system This screen displays historical information for each errors. Each error entry includes a description and error pump including material usage and pump cycles. The code along with a date and time stamp.

  • Page 68: Optional Screens

    Appendix C - ADM Run Screens Overview Optional Screens The optional Diagnostic screen can be enabled in the Advanced #4 screen, see page 64. Diagnostic The Diagnostic screen shows status information for var- ious system components. 313873J...

  • Page 69: Appendix D - Adm Event And Error Codes Overview

    Appendix D - ADM Event and Error Codes Overview Appendix D - ADM Event and Error Codes Overview Event Codes Event Code and String Triggers Event Code and ENN0-R: Automatic The system was successfully charac- String Triggers Cal. Performed terized with the Automatic calibration. EAA0-R: Base Purge Base purge performed EQU1-R: Settings The system settings were successfully...

  • Page 70: Error Codes

    Appendix D - ADM Event and Error Codes Overview Error Codes Error Error Code Error Name Error Description Type Cause Solution The three point calibration data is invalid, system will operate in weight mode but will attempt Invalid to volumetrically calculate 0500 Weight Cal.
  • Page 71 Alarm Current commanding too much current Module code software, if problem persists contact Graco On the ADM go into the Setup screens to the System Pumps are defined with The requested dispense screens then make sure that the pump sizes are...
  • Page 72 Appendix D - ADM Event and Error Codes Overview Error Error Code Error Name Error Description Type Cause Solution Pump cannot reach the Increase restriction in the system requested pressure Setpoint Not D2A1 The set point was not reached Deviation Reached Pump cannot reach the Decrease restriction in the system...
  • Page 73 Appendix D - ADM Event and Error Codes Overview Error Error Code Error Name Error Description Type Cause Solution Red Low L111 Deviation Tanks low on material Fill tanks with material Material Level If the tanks appear to have plenty of material check to Low material level in tanks Deviation Loose/broken connection make sure the level sensor is connected to the proper...
  • Page 74 Appendix D - ADM Event and Error Codes Overview Error Error Code Error Name Error Description Type Cause Solution Red Pressure Dispense valve failed to Check to make sure the dispense valve is properly P4A1 Alarm Shutdown open configured and connected to the MCM Bad dispense valve Replace dispense valve Restriction in the...
  • Page 75 Appendix D - ADM Event and Error Codes Overview Error Error Code Error Name Error Description Type Cause Solution Red Tank T1A6 Low Fluid Alarm Temp. Blue Tank T1B5 Low Fluid Alarm Temp. Red Inline T1A3 Low Fluid Alarm Tripped circuit breaker Visually check circuit breaker for a tripped condition Temp.
  • Page 76 Appendix D - ADM Event and Error Codes Overview Error Error Code Error Name Error Description Type Cause Solution No power to fan Check cord to make sure fan has power Debris in fan or heatsink Clear debris from fan or heatsink The temperature the MCM has Try to stop fan by lightly pressing on the center with a reached a level where product...
  • Page 77 Appendix D - ADM Event and Error Codes Overview Error Error Code Error Name Error Description Type Cause Solution No Cooling T8A7 Alarm Tripped circuit breaker Visually check circuit breaker for a tripped condition Red Chiller Disconnect the valve and measure the voltage across the wires when the chiller is running to ensure 24V is Defective cooling valve No temperature decline...
  • Page 78 Appendix D - ADM Event and Error Codes Overview Error Error Code Error Name Error Description Type Cause Solution The voltage to the MCM has Motor Control reached an unsafe level and Supply lines providing Check incoming voltage to ensure it is below the V4H0 Alarm Overvoltage...
  • Page 79 Appendix D - ADM Event and Error Codes Overview Error Error Code Error Name Error Description Type Cause Solution Red Tank WMC6 Alarm Con. Fault Blue Tank WMC5 Alarm Con. Fault Red Inline WMC3 Alarm Con. Fault Blue Inline WMC1 Alarm Con.

  • Page 80: Appendix E - Usb Operation

    Appendix E - USB Operation Appendix E - USB Operation The second option is the Erase icon which will reset the NOTICE last download date to a time where all logs can be Low-quality USB stick drives may lead to burning downloaded.

  • Page 81: Log Files, Folder Structure

    Appendix E - USB Operation Log Files, Folder Structure . 16: DOWNLOAD, DATAxxxx Folders Each time a stick-drive is inserted into the ADM USB port, a new folder named DATAxxxx is created. The number at the end of the folder name is incremented each time a stick-drive is inserted and data is transferred through the USB. In each DATAxxxx folder there are three log files.
  • Page 82 Appendix E - USB Operation Example 2-JOB File The 2-JOB file is the Shot Data log file. Example 3-SYSTEM File The 3-SYSTEM file is the Software Version log file. 313873J...

  • Page 83: Transfer System Settings

    The user should never attempt to modify the SET- then back to the ON position. TINGS.TXT file in any way. Graco is not responsi- ble for damages caused by an improperly modified 8. Plug the USB stick-drive into a computer.

  • Page 84: Update Custom Language

    Appendix E - USB Operation Update Custom Language Use the following process to customize the text on the NOTE: Immediately following uploading the language ADM. The language file DISPTEXT.TXT can be modi- file, remove the DISPTEXT.TXT file from the UPLOAD fied in Excel but must be saved as a Unicode Text file folder to prevent accidental loss of data the next time with the extension .TXT in order for it to properly import.
  • Page 85 Appendix E - USB Operation Example SETTINGS.TXT File Example DISPTEXT.TXT File NOTICE The user should never attempt to modify the SET- TINGS.TXT file in any way. Graco is not responsi- ble for damages caused by an improperly modified setup file. 313873J...

  • Page 86: Technical Data

    Technical Data Technical Data Air Inlet Pressure ......85-100 psi (0.59-0.69 MPa, 5.9-6.9 bar) Wetted Parts .

  • Page 87: Graco Standard Warranty

    With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective.

This manual is also suitable for:

Vrm 24f391Vrm 24f873

Table of Contents