Ods - Operator Display For Sequencer - Siemens 353 User Manual

Function Blocks

3.2.58 ODS - Operator Display for Sequencer

ODS function blocks are one of five operator displays
available on a one per loop basis to configure the local
operator display functions as well as the network
commands from an operator workstation associated with
the loop. See the i|ware PC faceplate example on the
following page.
The VIEW OD parameter, when set to YES, the default
value, enables the operator display to be viewed and
accessed locally using the LOOP button. Set the
parameter to NO to view the display or operation
parameters only with a network workstation and not
allow operation from the local display. This may be
desired with a sequence/logic loop where local operation
is not needed but a workstation needs access to force I/O
or sequence parameters for recipe changes.
Messages will be available over Modbus and
Modbus/TCP. Refer to Section 5 Network
Communications for mapped data points.
1. The # of Recipe messages can be set to 0 so that a
Recipe Message does not appear in the message list.
2. Messages will function as follows with the local
faceplate display:
When the local display first enters a loop, the
convention loop tag and sequence step number will
be displayed. When the D button is pressed, the
Numeric display will show MSG and the
alphanumeric display will show the first message it
comes to in the order shown below.
•
Conditional messages will be displayed in the
order in which they occurred.
•
The latest message will be displayed first.
•
A new message will override the current message.
The ACK button can be used to scroll through active messages.
It will stay on the last message until a new message overrides it
or the ACK button is again pressed. When an active message
clears, the message display will loop back and start at the top
and display the first message it comes to. Events that require
acknowledgment will return the display to the normal mode (i.e.
<loop tag>.S) and will flash the message. When events have
been acknowledged they can be viewed using the ACK button.
The display can be returned to the MSG mode using the D
button and will then display the first message in the Queue.
Output LE is high (1) when a loop event is active. Output SE is high
when a station error is active.
The LOOP # will be used to index reads and writes to Modbus parameters. The LOOP# must be entered to enable
Modbus and Modbus/TCP communications.
3-60
OPERATOR DISPLAY for SEQUENCER
ODS
OPERATOR
DISPLAY
S tep N umber
SN
R ecipe N umber
RN
SEQUENCER
Condition Msg 01 01
Optional Inputs
for
Condition Messages
nn
Condition Msg nn
CL
C onsole/ L ocal
NETWORK
E merg. L ocal EL
INTERFACE
# R M S G
# of Recipe MeSsaGes
M S G
# P
# of Primary MeSsaGes
# S M S G
# of Secondary MeSsaGes
# C M S G
# of Condition MeSsaGes
L O O P #
LOOP # ........................................... 01 to 25
(S)
W
V I E O D
VIEW Operator Display
I N P U T S N
INPUT SN
(H)
I N P U T R N
INPUT RN
(H)
I N P U T C L
INPUT CL
(H)
I N P U T E L
INPUT EL
(H)
R M S G x
Recipe MeSsGe x
P M S G x x
Primary MeSsGe xx
P M x x S S
Primary Message xx Starting Step
S M S G x x x
Secondary MeSsGe xxx
S M x x x S S
Secondary Msg xxx Starting Step
C M S G x x
Condition MeSsGe xx
I N P U T n n
INPUT nn
(H)
<Loop tag>.S
UM353-1B
LE L oop E vent
for
SE S tation Error
C o N sole
CN
C o M puter
CM
LO L ocal O peration
NL N ot L ocal
W atch D og
WD
..........................0 - 9
(1)
(H)
...................... 0 - 64
(H) (0)
............... 0 - 128
(H) (0)
................... 0 - 64
(0)
(H)
(null)
................. NO/YES YES
(H)
...................
loop tag.block tag.output (null)
...................
loop tag.block tag.output (null)
...................
loop tag.block tag.output (null)
....................
loop tag.block tag.output (null)
.................. 12 char ASCII
(S) ( )
................. 8 char ASCII
(S) ( )
.... 0 - 255
( )
(S)
........ 12 char ASCII
(S) ( )
.... 0 - 255
(S) ( )
............ 16 char ASCII
(S) ( )
....................
loop tag.block tag.output (null)
Rev. 3
D
Recipe Msg.
Primary Msg.
Secondary Msg.
Conditional Msg. 1
Conditional Msg. n
ACK
April 2012