Table of Contents
Advertisement
STATUS
'Buffer Display'
<Use Up and Down keys to Scroll>
dte#1
TEST
1=Loopback DTE
2=Loopback Netw.
dte#2
3=Loopback Proto
4=Loopback Remot
5=Test Remote
6=Lpbk Disable
1=No Rem Lpbks
7=NEBE/FEBE
2=DDS Accepted
8=Software Ver
3=V54 Accepted
9=Lpbk Both DTE
4=DDS + V54 Accept
0=Test 2047 Both
1=Netw. options
1=Dial Line
2=Leased Line
CONFIG
1=Asynchronous
2=DTE options
dte#1
dte#2
2=Synchronous
dte#1
3=Protocol
dte#2
dte#1
4=Quick setup
1=Dial 56K sync
2=Dial 64Ksync
dte#2
3=Dial 112K sync
4=Dial 128K sync
5=Dial 57.6 asyn
6=Dial 115.2 asy
7=Fallback 57.6k
8=Leased 64K
9=Ldm 64K Master
5=Security
Password < >
1=Set Password
2=Lock Keypad
Password Required
6=Remote Config
dte#1
1=Hang up line
DIAL
dte#2
2=Dial number
3=Redial last #
4=Answer Call
5=Dial Stored #
6=Store/Review #
D
ISU 2x64 Dual Port ISDN Service Unit User Manual
Chapter 6. Configuration
1=AT&T 5ESS
2= DMS-100
3=National ISDN1
4=NEC Switch
1=Switch Protocl
5=TDX10*
*Only available on part number
6=TDX1B*
1200051L5 and 1200051L6.
7=EuroISDN*
8=VN4*
9=KDD*
10=NTT*
dte#1
2=Call type
1=Speech
2=Audio
dte#2
3=Data 56Kbps
4=Data 64Kbps
3=Terminal ID
Set SPID
dte#1 <SPID>
dte#2 <SPID>
Set LDN
dte#1 <LDN>
dte#2 <LDN>
4=Busy Out
1=Enabled
2=Disabled
1=Front Panel
2=RS-366
3=AT commands
dte#1
5=Dial options
4=V.25
dte#2
5=Disabled
dte#1
6=Auto answer
1=Disabled
2=Enabled
dte#2
3=Dump all calls
dte#1
7=Answer tone
1=No answer tone
2=Incoming tone
dte#2
3=Outgoing tone
4=Always tone
8=Connect Timout 1=15 sec
2=30 sec (def)
3=1 minute
4=2 minute
5=4 minute
9=Call Screening
1=Answer any
1=Clock mode
2=Ansr if SNO...9
2=Channel rate
10=SBUS Terminati 1=100 ohm On
2=100 ohm Off
3=SBus Terminati
1=Bit Rate
1=TXINIT
1=Clear Channel
2=TXFA
2=BONDING mode 1
3=TXADD01
3=V.120
4=TXDEQ
2=Connector Type
4=V.110
5=TANULL
5=DSU 57.6 ASYNC
6=TCID
6=T-LINK
7=Async Rev
3=RTS Options
7=SAP
8=FALLBACK
1=PPP
9=PPP asyn-sync
2=Multilink PPP
4=CTS Options
3=PPP w/Comp
5=CD Options
6=DTR Options
1=Number < >
dte#1
1=Cfg. Rmt. Unit
2=Password < >
7=DSR Options
dte#2
2=Set Password
Password < >
3=Lpbk remote 1B Number < >
4=Lpbk remote 2B Number < >
8=Transmit Clock
Figure 6-3
LCD Configuration Menu Tree
KEY
dte#1
dte#2
This symbol means the menu items that follow can
be configured for DTE#1 or DTE#2 when entering these
portions of the menu tree. Use the up and down ARROW
keys to choose DTE#1 or DTE#2.
Press ENTER to select.
Use the CANCEL key to back up.
1=1 sec or EON
2=2 sec or EON
3=5 sec (default)
4=10 sec or EON
NOTE: Bold type represents default.
5=20 sec or EON
6=Wait for EON
1=V.25 HDLC
2=V.25 ASYNC
3=V.25 BISYNC
4=V.25 HDLC FLAG
1=Bit Rate
2=Connector Type 1=RS-530
1=Slave
2=Master
3=RTS Options
1=64k
2=128k
4=CTS Options
1=100 ohm On
2=100 ohm Off
5=CD Options
1=2400
6=48000
6=DTR Options
2=4800
7=56000
3=9600
8=64000
4=19200
9=112000
5=38400
0=128000
1=RS-530
2=V.35
7=DSR Options
3=RS-232
1=1 ms delay
2=18 ms delay
8=Flow Control
1=Forced CTS
2=Follows RTS
1=CD Forced on
9=Data Format
2=Normal
3=Off with LOCD
4=Off Link Down
1=Ignore DTR
2=Cmd when Off
3=Idle when Off
4=Off>On dial #0
5=Dial #0 if On
6=Answer if On
1=DSR forced on
2=OFF Idle+Test
3=OFF Link Down
1=Normal
2=External
29
1=300
6=19200
2=1200
7=38400
3=2400
8=57600
4=4800
9=115200
5=9600
2=V.35
3=RS-232
1=1 ms delay
2=18 ms delay
1=Forced CTS
2=Follows RTS
1= CD Forced on
2=Normal
3=Off with LOCD
4=Off Link Down
1=Ignore DTR
2=Cmd when Off
3=Idle when Off
4=Off>On dial #0
5=Dial #0 if On
6=Answer if On
1=DSR forced on
2=OFF Idle+Test
3=OFF Link Down
1=Hardware Flow
2=Software Flow
3=No Flow Ctrl
1=Data Bits
1=8 Data bits
2=7 Data bits
2=Parity Bits
1=None
2=Odd
3=Even
3=Stop Bits
1=1 Stop bit
2=1.5 Stop bits
3=2 Stop bits
Advertisement
Table of Contents
