HP 8901B Operation And Calibration Manual page 432

Model 8901B
Index
losing instrument states, 3-211
low-noise
Lo
frequency tuning, 3-115
LP FILTER, 3-179
resolution, finer for audio frequency measurements, 3-200
resolution,
frequency, 3-131
RF
power calibration factor, 3-79
M
manual calibration factors for RF power, 3-79
manual tuning, 3-115
measurement codes used in limits, 3-220
RF
and IF filters, 3-241
RF
filters, 3-229
MODULATION OUTPUT, 3-187
modulation range, 3-183
multi-channel transmitters, checking channel accuracy, 3-123
multiple signal sources, measuring, 3-113, 3-119
N
noise effects, residual, 3-191
noise measurements, single-sideband, 3-95
normalizing noise measurements, 3-95
0
offset in input attenuation, compensating for, 3-105
offsetting the
LO,
for selective power measurements, 3-95
option 003, 3-129
option 030, 3-95, 3-245,
P
parta per million display; frequency error measurments, 3-123
peak detectors,
phase lock,
LO
does not, 3-128
phase modulation, 3-169
in AM measurements, 3-137
in FM measurements, 3-154
in degrees, 3-172
recommended filter selection, 3-172
phase shift keying, 3-172
power measurements, RF, 3-71
power measurements, adjacent channel, 3-95
power sensor,
changing, 3-79
in RF power measurements, 3-71
user-built, 3-79, 3-107
power-up and default conditions, 3-209
pre-emphasis equalization, 3-159
program, example for entering
RF power cal factors, 3-81
pulsed phase modulation, 3-172
PREVIOUS
RATIO,
3-215,3-243
pull-Out cards, 3-2
R
RANGE HOLD, 3-213
range, audio, 3-183
range, modulation, 3-183
ratio measurements, common, 3-218
recalibrating RF power, reasons, 3-78
RECAL,
receiver, setting up the 8901 as, 3-235
recorder output, for RF power measurements, 3-87
remote control RF switch, 3-107
residual noise effects, 3-191
RATIO, 3-215,3-219
RECALL, 3-223
in RF power measurements, 3-78
RF
frequency error, 3-121
RF frequency resolution, 3-131, 3-242
RF
frequency tuning, 3-115
RF
input attenuation, 3-231, 3-241
RF
input frequency, 3-111
RF
level measurements, 3-85
RF
power range, 3-243
RF
POWER, 3-71
calibration, 3-71
reasons
to
recalibrate, 3-78
using the internal voltmeter with, 3-87
RF
POWER, when initiates
RF
level measurements, 3-85
r m s calibrated average as peak, 3-218
rms calibrated average as true average, 3-218
RMS, 3-201
RMS detector, considerations when using, 3-154
S
SAVE CAL,
in
AM
calibration, 3-141
in FM calibration, 3-155
F W
power calibration, 3-71, 3-80
selective power measurements, 3-95, 3-245
selectivity, increasing, 3-229
sensitivity,
increasing, 3-229
sensor module,
in
RF
power measurements, 3-71
user-built, 3-79,3-107
sensor, power, in RF power measurements, 3-71
service request, 3-26, 3-244
SINAD, 3-203, 3-245
single-sideband noise measurements, 3-95, 3-98
source impedance, 3-79
special display, 3-239
special, special display, 3-240