Yamaha F225F Service Manual page 557

F.
Fail-safe control ........................................2-16
Feature........................................................4-1
Flywheel magnet.......................................7-14
Forward gear shim (T1) selection table ....8-56
Forward gear shim (T2) selection
chart ........................................................8-93
Front...................................................5-6, 5-14
Fuel and oil requirement .............................1-6
Fuel control unit and components.............5-34
Fuel diagram .............................................2-26
Fuel filter assembly .....................................6-9
Fuel hose and blowby hose ........................6-1
Fuel injection amount compensation ..........2-7
Fuel injection control system.....................1-10
Fuel injector ..............................................6-43
Fuel injector anti-sticking control.................2-7
Fuel system..................... 1-17, 1-26, 2-26, 6-6
Fuel system technical data .......................1-17
Fuel unit ..................................................... A-5
Function ......................................................4-2
Fuse box ...................................................7-24
Fuse holder .................................................5-3
G.
Gauge/sensor ...........................................1-15
General feature ...........................................1-1
General Periodic Maintenance..................10-7
General tightening torque .........................1-30
H.
Handling of gas torch ..................................0-2
Handling of gasoline ...................................0-1
Handling of sealant .....................................0-3
Hardware requirement ................................4-1
Hose routing................................................6-1
Hot part .......................................................0-1
How to use this manual...............................0-4
I.
Ignition timing compensation ......................2-9
Ignition timing control ..................................2-8
Ignition timing control system......................1-8
Ignition timing restriction .............................2-9
Ignition unit................................................. A-7
Ignition units and components ..................5-45
Install the forward gear .............................8-28
Install the reverse gear .............................8-79
Installing the battery cable ..........................3-9
Installing the camshaft and driven
sprocket ..................................................7-48
Installing the canister................................ 6-27
Installing the clamp bracket ...................... 9-27
Installing the cowling lock lever .................. 9-6
Installing the cylinder head ....................... 7-62
Installing the Digital Electronic Control box and
switch panel............................................ 3-12
Installing the drive shaft................... 8-28, 8-79
Installing the engine ECM......................... 7-33
Installing the flushing hose ......................... 9-5
Installing the flywheel magnet .................. 7-15
Installing the fuel filter assembly............... 6-12
Installing the fuel injector .......................... 6-44
Installing the intake manifold .................... 6-16
Installing the intake silencer ..................... 6-18
Installing the isolator lead ......................... 3-10
Installing the junction box ......................... 7-28
Installing the knock sensor ....................... 7-73
Installing the lower unit
(U-transom model)......................... 8-34, 8-80
Installing the lower unit
(X-transom model)......................... 8-33, 8-80
Installing the low-pressure fuel pump ....... 6-31
Installing the main harness......................... 3-8
Installing the oil cooler .............................. 7-68
Installing the oil filter bracket .................... 7-69
Installing the oil pump assembly............... 7-68
Installing the power unit............................ 7-10
Installing the propeller shaft housing
assembly ....................................... 8-29, 8-79
Installing the PTT motor ........................... 9-43
Installing the PTT switch............................. 9-9
Installing the PTT unit............................... 9-36
Installing the pulley bracket ...................... 7-73
Installing the Rectifier Regulator............... 7-29
Installing the reservoir .............................. 9-43
Installing the rigging grommet .................... 3-9
Installing the shift actuator assembly........ 7-35
Installing the shift rod....................... 8-31, 8-80
Installing the shift rod and SPS .................. 9-2
Installing the speed sensor....................... 3-11
Installing the starter motor ............... 5-63, 7-31
Installing the steering arm ........................ 9-23
Installing the thermostat ........................... 7-73
Installing the throttle body and
surge tank............................................... 6-23
Installing the tilt cylinder ........................... 9-56
Installing the tilt ram.................................. 9-57
Installing the timing belt ............................ 7-39
Installing the trim ram ............................... 9-56
Installing the upper case........................... 9-12
Installing the vapor separator ................... 6-36
Installing the water pressure sensor......... 3-10
Installing the water pump................. 8-31, 8-80
Installing the wiring harness ..................... 7-20
Index
0
1
2
3
5
6
7
8
9
10
10
A
i-4