Grizzly G0812 Owner's Manual page 23

10. Check function of cutting fluid pump
by turning
( , D) all the way to the right.
STAND BY
A B
11. Verify that cutting fluid flows through nozzles
A
into blade guides, then turn switch OFF.
STAND BY
B
A B
<< I
START
F
E
12. Press raise headstock button (
raise headstock several inches, then press
C
vise close (
<< I
START
F
E
I
A
Note: As a safety precaution, saw motor will
OFF
LOW HIGH
B
not start unless vise close button is pressed
I first.
J
OFF
L
C
LOW HIGH
13. Start blade movement by pressing blade start
button (
0
J
1 9
Emergency Stop button (
2
should run smoothly and without unusual
D E
F
problems or noises.
3
0
1
4 6
5
14. Press Emergency Stop button ( 2
pletely to stop machine.
STAND BY
3
A B
4
5
15. WITHOUT resetting Emergency Stop button,
press hydraulic motor button (
L
close button (
<< I
START
F
E
( , I). The machine should not start.
— If machine does not start, Emergency Stop
E
D
G
F
button safety feature is working correctly.
I
Congratulations! Test Run is complete.
OFF
LOW HIGH
— If machine does start (with Emergency
Stop button pushed in), immediately dis-
connect power. Emergency Stop button
is NOT working properly and must be
replaced before further using machine.
1
2
16. Reset Emergency Stop button, repeat Steps
3
12–13, then press Stop button (
4
machine.
STAND BY
A B
17. WITHOUT pressing Stop button again, press
hydraulic motor button (
L
button (
<< I
START
F
E
( , I). The machine should not start.
18. Open blade cover and lock in position (see
D E
G
F
Figure 21). This activates blade cover safety
I
switch to prevent saw starting.
OFF
LOW HIGH
J
Model G0812 (Mfd. Since 2/16)
0
1 9
cutting fluid pump
C D
D
C
G
H
L
, J) button.
G H
K
M
K
D E
F
STOP
K
M
I J
STOP
L
, I) while keeping your finger near
A
, C). The machine
C
8
G H
B
D
E F
L
7
A
G H K
I J
9
B
A
8
7
B
D
E
K
C D
6
C
G H
I J
I , J), then blade start button J
G
H
D
H
K
STOP
J
A
B
L
0
9
8
C
A
7
B
6
5
K
C D
E
D
C
, G), vise close
, J), then blade start button
I J
G
H
D
H
K
M
STOP
L
switch
K
, E) and
Figure 21. Wheel cover locked in "up" position.
I J
19. While staying safely away from blade, press
G H
, C) in com-
C
F
L
K
, G), vise
20. Press Emergency Stop button (
E
G
F
21. Reset Emergency Stop button.
22. Raise headstock up all the way, then start
M
K
L
I
K
, H) to stop
L H
G
F
I
E
H
G
F
23. Press Emergency Stop button. Test Run is
Stop button again, press hydraulic motor but-
ton, vise close button, then start button.
— If blade does not start, blade cover safety
switch feature is working correctly.
— If blade does start (with blade cover open),
immediately turn machine OFF and dis-
connect power. Blade cover safety switch
safety feature is not working correctly.
K
This safety feature must work properly
before proceeding with regular operations.
Call Tech Support for help.
I J
A
pletely, then close wheel cover and secure.
D
H
G
blade. When headstock reaches bottom of
travel, the blade should shut off and the
headstock should move back to the top of its
travel.
— If blade does shut off and headstock
moves back to top of its travel, upper limit
switch is working correctly.
J
— If blade does not stop or headstock does
not move back to top of its travel, upper
limit switch is not working correctly. This
J
safety feature must work properly before
proceeding with regular operations. Refer
to Page 57 to adjust this limit switch.
complete.
, C) in com-
C
B
E F
H
I J K
-21-