Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for CyberPower CPS5000ECH48
Summary of Contents for CyberPower CPS5000ECH48
- Page 1 All-In-One Off-Grid Inverter User’s Manual ’ M...
-
Page 2: Table Of Contents
The unit is compatible with lead acid battery. For lead acid battery, you are easy to find it on the market. 3 Installation........................5 However, we strongly recommend you to contact your installer or CyberPower system to confirm before the 3.1 Unpacking and Inspection ........................5 procedure. -
Page 3: Basic System Architecture
Solar power Figure 1-2 NOTE: Generator For parallel model installation and operation, please see section 6.1 for details. Only CPS5000ECH48 have the function. Position Description LCD Display... -
Page 4: Safety Instructions
Setting screws 3 appropriate sections of this manual. The company has the right not to quality assurance, if not Parallel communication cable 1 (CPS5000ECH48-P only) according to the instructions of this manual for installation and cause equipment damage. Current sharing cable 1 (CPS5000ECH48-P only) b. -
Page 5: Inverter Connection
Ring Terminal Figure 3-3 Max. Battery Wire Recommended Torque Dimensions Model Name Charging Cable Model Name Capacity Size Charge Current Value Current CPS5000ECH48/CPS5000ECH48-P 248mm(9.76") 380mm(14.96") 69mm(2.71") (mm) (mm) CPS3000ECH48 248mm(9.76") 355mm(13.97") 84mm(3.3") CPS5000ECH48 130A 200AH 2*8AWG 29.2 2-3Nm CPS5000ECH48-P CPS3000ECH48... - Page 6 AC input connection. To reduce risk of injury, please use the proper recommended cable size as below. Suggested cable requirement for AC wires Figure 3-7 Model Name Wire size Torque value CPS5000ECH48/CPS5000ECH48-P 1*8AWG 1.4-1.6Nm WARNING: Shock Hazard CPS3000ECH48 1*10AWG 1.4-1.6Nm...
- Page 7 Max charging Model Name Diameter Torque unit. current per string d. Then, insert AC output wires according to polarities indicated on terminal block and tighten terminal CPS5000ECH48/CPS5000ECH48-P 1*10AWG 1.2-1.6Nm screws. Be sure to connect PE protective conductor first. CPS3000ECH48 1*10AWG 1.2-1.6Nm...
-
Page 8: Communication Connection
4 Communication Connection b. Check correct polarity of connection cable from PV modules and PV input connectors. Then, connect positive pole (+) of connection cable to positive pole (+) of PV input connector. The unit is compatible with RS232 and RS485 communication. Connect negative pole (-) of connection cable to negative pole (-) of PV input connector. -
Page 9: Dry Contact
6.1 Introduction of parallel Dry contact port: CPS5000ECH48-P can be used in parallel operation in single phase with up to 3 units. The following Unit Status Condition items were used, if you need parallel function. - Page 10 Recommended breaker specification of battery for each inverter Model Name 1 unit* CPS5000ECH48-P 100A/60VDC If you want to use only one breaker at the battery side for the whole system, the rating of the breaker should be X times current of 1 unit. “X” indicates the number of inverters connected in parallel. But we suggest that each inverter has a battery breaker.
-
Page 11: Operation
Buzzer 7 Operation Status Description 7.1 Power ON/OFF Beeps every 3 seconds Inverter is in warning state Once the unit has been properly installed and the batteries are connected well, simply press On/Off Beeps constantly Inverter is in error state switch (located on the button of the case) to turn on the unit. - Page 12 Display Item Description Items Description It presents battery capacity. Each interval indicates battery capacity level by Vb/Cb: xx.xV/ xxx% Battery Voltage/Battery Capacity 0-20% Vpv: xxxV/ xxxV PV Voltage PV1 Voltage/PV2 Voltage Ic_pv: xx.x / xx.x A PV Charge Current: PV1 Charge Current/ PV2 Charge Current Load power: Each interval indicates load level by 0-25% Ppv: xxxx/ xxxxW PV Charge Power: PV1 Charge Power/ PV2 Charge Power...
- Page 13 Function Description Status Description When the power switch is turned on, after pressing and holding Enter button immediately for 3 Item Description seconds, the unit will into the setting mode. Press “UP” or “DOWN” button to select setting programs. And then, press “ENTER” button to confirm the selection or ESC button to exit. Battery powers the load.
- Page 14 Common application. (APL: Appliances) AC Input Mode (default) battery low cut-off voltage. UPS:170-280VAC UPS application. Only CPS5000ECH48-P has shown AC Output Mode. The unit Single (default) 208VAC AC output voltage 208VAC. AC Output Mode works in parallel mode if setting "Parallel". Otherwise, the...
-
Page 15: Specifications
Description Power FB Protect Power feedback protection Line Mode Specifications Share-Curr Fault Current sharing fault Model Name CPS3000ECH48 CPS5000ECH48 CPS5000ECH48-P CAN Fault CAN communication fault Input Voltage Waveform Sinusoidal (utility or generator) Host Loss Host inverter loss Nominal Input Voltage... - Page 16 PV Mode Specifications Bat Mode Specifications Model Name CPS3000ECH48 CPS5000ECH48 CPS5000ECH48-P Model Name CPS3000ECH48 CPS5000ECH48 CPS5000ECH48-P MPPT No Rated Output Power 3KVA/2.4KW 5KVA/4KW Max. Input Power Per MPPT 1750W Output Voltage Waveform Pure Sine Wave Max. Input Current Per MPPT...
-
Page 17: Trouble Shooting
The warranty shall also cease to apply if the product cannot be correctly identified as the product of CyberPower. Warranty claims will not be honored if the type of serial number on the machines have been altered, removed or rendered illegible. -
Page 18: Contacts
12 Contacts 11 Appendix If you have technical problems concerning our products, contact your installer or CyberPower. During The following chart is the inverter optional appendix list, if there is a need please contact the inquiring, please provide below information: CyberPower or our local distributors. - Page 19 Note Note...
- Page 20 K01-TP11001-00...