Related Manuals for CyberPower CPSPV3600ETL
Summary of Contents for CyberPower CPSPV3600ETL
- Page 1 User’s Manual CPSPV3600ETL CPSPV3000ETL CPSPV2000ETL CyberPower Systems Inc. www.cpsww.com...
-
Page 2: Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS Save These Instructions! This manual contains important constructions that shall be followed during the installation and maintenance of the CyberPower Grid Tie Solar Inverter. CAUTION! Before installation and using the Inverter, read all About This Manual instructions and cautionary markings on the inverter and appropriate This purpose of this Installation &... - Page 3 UNPACKING 2) Stainless wall mount bracket 1) CPSPV2000ETL 、 C PSPV3000ETL or 3) User’s manual 4) Warranty card CPSPV3600ETL module 5) Self-tapping screws: M6*20L(5) Copyright © 2012 CyberPower Systems, Inc.
-
Page 4: Inverter Location
Installation CyperPower Grid Tie Solar Inverter The CyberPower Grid Tie Solar Inverter is designed to convert solar Inverter Location electric (photovoltaic or PV) power into utility-grade electricity that can be used by the home or sold to the local power company. - Page 5 Equipment and Installation Recommendation The maximum power point voltage of a string connect to the inverter should be a minimum of 250Vdc for CPSPV3600ETL model. If it is less Equipment recommendations than 250Vdc for CPSPV3600ETL model, the inverter will continue to...
-
Page 6: Routing The Wires
This section includes the following topic: MPPT start Wiring The wires to AC terminal: voltage (Vdc) Acceptable wire size: For CPSPV3600ETL: From #12 AWG to #10 AWG (3mm to 6mm MPPT window 100~550 100~550 100~550 For CPSPV3000ETL: From #14 AWG to #12 AWG (2mm... -
Page 7: Mounting The Inverter
If your installation location requires that you drill additional conduit holes into the bracket, ensure that there are no metal shavings left inside the unit. These could cause a short circuit when unit is operating. Copyright © 2012 CyberPower Systems, Inc. - Page 8 E : LED Indicator Light (Green) – Flash: Standby for reconnection / Solid: Operation ○ F : LED Indicator Light (Red) – Warning condition ○ G : LED Indicator Light (Yellow) – Ground fault Copyright © 2012 CyberPower Systems, Inc.
- Page 9 4 : M20*1.5 cable glands * 2pcs: For RS-485 communication ○ 5 : M20*1.5 cable gland * 1pcs: For RM card communication ○ 6 : AC connector (male): Connect to the utility output Recommended female type: PWJ-03BFFB-LL8001 (Amphenol) Copyright © 2012 CyberPower Systems, Inc.
-
Page 10: Start-Up Procedure
The default voltage, frequency and reconnect delay values are programmed into the unit at time of shipment from the factory. No changes to these settings can be made in the field by the user. Only authorized personnel with utility permission may change these settings. Copyright © 2012 CyberPower Systems, Inc. -
Page 11: Monitoring The Inverter
E-day: Today the inverter provided how much energy to the grid. Select language Press “Enter” key 2. Main menu: Select date & time After you select above three items, the display will enter into “Home Page” Copyright © 2012 CyberPower Systems, Inc. - Page 12 In “Main Menu”, select Multi meter, then press In “Data Logger”, select Daily Log, then press “Enter” key “Enter” key 2.3.1 Daily Log: 2.2 Multi meter: In “Data Logger”, select Monthly Log, then press “Enter” key 2.3.2 Monthly Log: Copyright © 2012 CyberPower Systems, Inc.
- Page 13 There are over last 100 dated failure reports on the NS protection can be read. In “Main Menu”, select Config, then press “Enter” key 2.5 Config: IMPORTANT: The settings only can be used by authorized personnel with utility permission. Copyright © 2012 CyberPower Systems, Inc.
- Page 14 The settings only can be used by authorized personnel with utility permission. In “Config”, select RMCard Set, then press “Enter” key 2.5.6 RMCard Settings: IMPORTANT: The settings only can be used by authorized personnel with utility permission. Copyright © 2012 CyberPower Systems, Inc.
- Page 15 Hardware CT failure Temperature sensor 2 high Hardware AC current OCP Hardware temperature sensor 2 DC input current high (slow) failure DC input current high (fast) Temperature sensor 3 high Hardware temperature sensor 3 Copyright © 2012 CyberPower Systems, Inc.
-
Page 16: Technical Specifications
Output AC fuse Current limitation and thermal de-rating Output protection Over temperature protection Utility voltage deviation < 1% Utility frequency deviation < 0.05Hz Output current deviation < 3% Output detection tolerance Output power deviation < 3% Copyright © 2012 CyberPower Systems, Inc. - Page 17 19.5 Kg 19.5 Kg Gross Weight 21.5 Kg 23 Kg 23 Kg Enclosure rating IP 65 Installation type Wall mount DC connector 1 pairs connectors AC connector Waterproof AC connector CyberPower Systems Inc. www.cpsww.com Copyright © 2012 CyberPower Systems, Inc.
-
Page 18: Explanation Of Symbols
Beware of hot surface. Observe enclosed documentation. There are special requirements. The inverter complies with the requirements of the applicable EC guidelines. The inverter must not be disposed of together with the household waste. Copyright © 2012 CyberPower Systems, Inc. - Page 19 0.45% 0.2 sec Ground Current (mA) 0.3 sec 0.3 sec 0.3 sec 0.3 sec Insulation 5 sec 5 sec 5 sec 5 sec Islanding Islanding Factor Active Power Reactive Power Frequency de-rating Power slow-up Copyright © 2012 CyberPower Systems, Inc.
- Page 20 Code setting table Reactive power measurement Copyright © 2012 CyberPower Systems, Inc.