System Programming Options; Introduction; Downloading From A Computer - NAPCO Gemini GEM-P1664EX Programming R Instructions

Page 4

SYSTEM PROGRAMMING OPTIONS

INTRODUCTION

The GEM-P1664EX control panel may be programmed by various means, each of which will be covered in detail in the
sections that follow. Keypad displays shown are for a GEM-RP1CAe2/K1CA (version 8 keypad), the recommended key-
pad for programming.
K3DGTL and the GEM-RP4RFC/GEM-K4RF series, see WI1387.

Downloading From a Computer.

downloaded from (or uploaded to) an IBM PC-compatible computer, either locally or remotely. Napco's PCD3000
Quickloader software features context-sensitive help screens as well as an error-checking utility that prevents pro-
gramming of incompatible or conflicting data to ensure proper panel operation.
Easy Menu-Driven Program (Dealer Program) Mode - Keypad Programming.
Program Mode allows keypad programming of number of zones in area 1, panel zone doubling, number of fire zones
(both 4-wire and 2-wire), local or Central Station reporting, number of exit/entry zones, number of interior zones, num-
ber of 24 hour zones, number of chime zones, Chime 2 zones, Exit/Entry2 zones, 50ms loop response zones, aux out-
put activated on alarm zones, sensor watch zones, keypad sounder on alarm zones, auto bypass re-entry zones,
EOLR zones, number of keypads in area 1, Central Station telephone number, Central Station account number, Cen-
tral Station receiver format, User Codes, RF transmitter points, RF keyfob transmitters, zone descriptions, date/time,
dealer code, Test Timer, Telco line fault test, Burg output chirp on keyfob, keypad time/date display, enable CP-01 pro-
gramming, and clear dealer program/cold start. For new panels, a custom default program may be created at the key-
pad. A menu-driven utility prompts the installer to configure the system. Further detailed customization is accom-
plished in the Direct Address Program Mode.
Direct Address (Dealer Program) Program Mode - Keypad Programming.
gram Mode is an extension of the Dealer Program Mode wherein data is entered at the keypad by location. This
mode is accessed from the Easy Menu Driven Program Mode by pressing the
User Program Mode - Keypad Programming.
and is limited to keypad programming of User Codes, Time, Date and Zone Descriptions.
DOWNLOADING FROM A COMPUTER
The control-panel program may be downloaded from the computer by any of the following methods.
Local Downloading
(Note: This procedure should be used after installation, after peripheral devices are connected).
For direct high-speed data transfer to the control panel from a desktop computer, connect the download jack (JP2)
on the panel to the LOCAL jack (J3) on the Napco PCI2000/3000 computer interface using the supplied 6-
conductor cable. (Refer to PCI2000/3000 Installation Instructions WI443 for wiring diagram and procedures).
Similarly, a high-speed local download may be made in the field using a notebook or laptop computer. Connect
JP2 on the control panel to a Napco PCI-MINI computer interface using the 6-conductor cable supplied. (Refer to
PCI-MINI Installation Instructions WI767).
Remote Downloading
(Also see PCI2000/3000 Installation Instructions WI443).
Function Mode
Start by establishing a telco connection between the computer operator and the installer. During this procedure,
voice contact will be lost, therefore both the installer and the computer operator should be familiar with the opera-
tion. When a steady high-pitched tone is heard at the site phone, access the "ACTIVATE DOWNLOAD" Function (see
Keypad Programming Modes), then press the
Hang up the phone and wait for a call from the central station confirming a successful download.
Callback Method
An installed, unattended panel may be programmed or reprogrammed remotely using the Callback-Method
Download feature of the PCD3000 software. Remote downloading requires a modem compatible with the
PCI2000/3000. Upon answering the call from the computer, the panel will verify the Download Security Code and,
if confirmed, will establish a connection. If a Callback Number is programmed into the panel, the panel will auto-
matically disconnect and call the computer at this number before establishing a connection.
X
GEM-P1664EX Programming Instructions
For Programming Instructions with the GEM-RP2ASe2/GEM-K2AS, GEM-RP3DGTL/GEM-
This is the preferred method of programming.
The User Program Mode is intended for authorized users
J U
or button or the
NEXT/YES
The panel may be
The Easy Menu-Driven
The Direct Address Pro-
button at any time.
C
button; the site phone will go dead.
L
NAPCO Security Systems
WI1386 5/05