Daikin Super Multi NX 3MXS-G Series Engineering Data page 253

Indoor Units
1. Removing packaging material.
•
Removal method
Grasp the packaging material which
is in the center of the front panel,
with one hand, and lightly pull the
front panel up and toward you.
2. Removing and installing front panel.
•
Removal method
Hook fingers on the panel protrusions on the left and right of the
main body, and open until the panel stops. Slide the front panel
sideways to disengage the
rotating shaft. Then pull the
front panel toward you to
remove it.
•
Installation method
Align the tabs of the front panel with the grooves,
and push all the way in. Then close slowly. Push
the center of the lower surface of the panel firmly
to engage the tabs.
3. Removing and installing front grille.
•
Removal method
1)Remove front panel to remove the air filter.
2) Remove the front grille. (2 screws)
3) In front of the
front grille, there are 3 upper hooks.
Lightly pull the front grille toward you
with one hand, and push down on
the hooks with the fingers of your
other hand.
1.
Installing the mounting plate.
• The mounting plate should be installed on a wall which can support the weight of the indoor unit.
1) Temporarily secure the mounting plate to the wall, make sure that the plate is completely level, and
mark the boring points on the wall.
2) Secure the mounting plate to the wall with screws.
Recommended mounting-plate retention spots and Dimensions
Recommended
mounting - plate
retention spots
(6 spots in all)
248
Installation Tips
Packaging material
Lightly lift.
Push the
rotating shaft
of the front
panel into the
groove.
Upper hook
mark of the
Lightly pull the front
Push
grille toward you with
down.
one hand, and push
down on the hooks with
the fingers of your other
hand. (3 locations)
Indoor Unit Installation (1)
b Place a leveler
on raised tab.
4-15/16
(Bolt size : 3/8 (M10))
(125)
φ3-1/8 (φ80)
2-15/16 (75)
2-3/8
(60) 12-1/8
(308.5)
Through-the-wall
Drain hose position
hole φ3-1/8 (φ80)
* The removed pipe port cover can be
kept in the mounting plate pocket.
<When there is no work space because the unit is close to ceiling>
CAUTION
Be sure to wear protection gloves.
Lift the panel
slightly and pull
Place both hands under the center of
out.
the front grille, and while pushing up,
pull it toward you.
•
Installation method
1) Install the front grille and firmly engage the upper hooks.
(3 locations)
2) Install 2screws of the front grill.
3) Install the air filter and then mount
the front panel.
4. How to set the
different addresses.
When two indoor units
are installed in one room,
the two wireless remote
mark area
controllers can be set for
(3 locations)
different addresses.
1) In the same way as
when connecting to an
HA system, remove
the metal plate
Upper hook
electrical wiring cover.
2) Cut the address
Upper hook
jumper (JA).
3) Cut the address
jumper (J4).
Leveling mounting plate
a Dangle a weighted thread and align thread with vertical arrow.
3-15/16
(Bolt size : 3/8 (M10))
(100)
φ3-1/8 (φ80)
3-15/16 3-7/8
(100) (98)
1-3/4
(44.5)
31-1/4
(795)
Gas pipe end
Liquid pipe end
Removed pipe
port cover
A Mounting plate
EDUS121131
1) Push up.
2) Pull toward you.
JA Address
EXIST 1
CUT 2
J4
J4 Address
EXIST 1
CUT 2
Use tape
measure
as shown.
Position the
end of tape
measure at ∇.
unit : inch (mm)
Installation Manual