Table of Contents
Advertisement
3
G E N E R A L
GAS INSTALLATION CODES
Australian Gas Association Approval No. 6029 and 6024.
Barbecues must be used in accordance with the installa-
tion requirements of your local gas supply authority, or
the appropriate installation standard AS5601/AG601.
Barbecues for use with cylinder gas are labelled
'Universal LPG'. Barbecues for use with natural gas are
labelled 'Natural Gas' and must be installed by an autho-
rised person. Check the gas type sticker attached to the bar-
becue. Check that the label matches the gas type for the
type of installation in which it is to be installed.
FAILURE TO COMPLY WITH THESE
!
INSTRUCTIONS COULD RESULT IN A
FIRE OR EXPLOSION WHICH COULD
CAUSE SERIOUS BODILY INJURY,
DEATH OR PROPERTY DAMAGE.
ACCESSIBLE PARTS MAY BE
!
VERY HOT.
KEEP YOUNG CHILDREN AWAY.
ANY MODIFICATION OF THIS
APPLIANCE MAY BE DANGEROUS.
DO NOT MOVE THIS APPLIANCE
DURING USE.
TURN OFF THE GAS SUPPLY AT THE
GAS CYLINDER AFTER USE.
READ THE INSTRUCTIONS BEFORE
USING THE APPLIANCE.
PARTS FULLY ASSEMBLED OR SEALED
BY THE MANUFACTURER MUST NOT
BE ALTERED IN ANY WAY.
THIS BARBECUE IS ONLY TO BE
USED AND STORED OUTDOORS.
OVERALL DIMENSIONS
Height – 1150 mm (Hood closed). 1565 mm (Hood open).
Width – 1740 mm (3&4 burner model, including trolley)
– 1900 mm (6 burner model, including trolley)
Depth – 660 mm
CLEARANCES
The following minimum clearances from combustible
materials must be maintained:
Rear – 800 mm (32"). Sides – 300 mm (12").
Openings at the rear and sides of the appliance
provide air for combustion and must not be obstructed.
I N F O R M A T
HOSE AND REGULATOR SAFETY
!
The regulator and hose assembly supplied with the
barbecue is suitable for using the barbecue on bottled gas.
A gas regulator adjusted to have an outlet pressure of
2.75 kPa is supplied for connection to the gas cylinder. The
pressure regulator and hose assembly supplied with the
appliance must be used. Replacement pressure regulators
and hose assemblies must be those specified by the
appliance manufacturer.
When connecting the hose and regulator assembly to
the gas cylinder, take care to avoid unnecessary twisting of
the flexible hose. After the assembly has been secured,
turn on the gas and check for leaks by brushing a soap
and water solution over all connections. Refer to page 4.
The presence of bubbles will indicate a gas escape. DO
NOT TEST FOR GAS ESCAPES WITH AN OPEN FLAME.
If you are unable to correct the leak by tightening the
connections, turn off the gas and contact the supplier
immediately.
Always ensure the appliance is kept away from
flammable materials and the gas cylinder clear of any heat
source.
When changing over from an empty gas cylinder to a
full one, make sure this procedure is carried out in a flame
free atmosphere.
Inspect the gas hose when replacing the gas cylinder,
or once a year, whichever is more frequent. If the hose is
cracked, cut, abraded or damaged in any way, the appliance
must not be operated. The hose must be replaced if
damaged or when statutory conditions require it.
Contact your supplier if uncertain.
The hose and regulator should be disconnected from
the cylinder when the barbecue is not in use.
!
SPECIFICATIONS
Appliance specifications can be found on the data
label attached to the barbecue.
Your barbecue is preset at the factory to operate on
bottled gas only, unless specified otherwise.
I
O
NEVER OPERATE THIS BARBECUE
WITHOUT A REGULATOR.
IF THIS INFORMATION IS NOT
FOLLOWED EXACTLY, A FIRE
CAUSING DEATH OR SERIOUS INJURY
MAY OCCUR!
DO NOT STORE A SPARE GAS
CYLINDER UNDER OR NEAR THIS
APPLIANCE.
THIS BARBECUE IS ONLY TO BE
USED AND STORED OUTDOORS.
3
N
Advertisement
Table of Contents
