Related Manuals for Planet FGSW-2022VHP
Summary of Contents for Planet FGSW-2022VHP
- Page 1 12-Port 10/100TX 802.3at PoE + 4-Port 10/100TX 802.3bt PoE + 2-Port Gigabit TP + 2-Port SFP Ethernet Switch with LCD Management FGSW-2022VHP User’s Manual...
- Page 2 Copyright Copyright © 2019 by PLANET Technology Corp. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of PLANET.
- Page 3 WEEE as unsorted municipal waste; WEEE should be collected separately. Revision PLANET 12-Port 10/100TX 802.3at PoE + 4-Port 10/100TX 802.3bt PoE + 2-Port Gigabit TP + 2-Port SFP Ethernet Switch with LCD Management User's Manual Model: FGSW-2022VHP Revision: 1.0 (Aug., 2019)
-
Page 4: Table Of Contents
Table of Contents 1. Introduction ....................5 1.1 Package Contents .................. 5 1.2 Product Description ................6 1.3 Features ....................8 1.4 Specifications ..................10 2. Hardware Description ..................12 2.1 Front Panel ..................12 2.1.1 CD Monitor Indicators ..............13 2.1.2 LED Indicators ................14 2.2 Rear Panel ...................15 2.3 LCD Management .................16 2.3.1... -
Page 5: Introduction
1. Introduction Thank you for purchasing PLANET FGSW-2022VHP 12-Port 10/100TX 802.3at PoE + 4-Port 10/100TX 802.3bt PoE + 2-Port Gigabit TP + 2-Port SFP Ethernet Switch with LCD Management. “LCD Switch” is used as an alternative name in this user’s manual. -
Page 6: Product Description
1.2 Product Description Just “Plug and Watch” for a Quick Solution PLANET FGSW-2022VHP is an ideal Plug and Watch Power over Ethernet solution which provides quick installation, real-time PoE work status monitoring and immediate troubleshooting through its unique LCD display to improve work efficiency and quality without any PC or software required. - Page 7 100BASE-TX UTP 100BASE-TX UTP with PoE In the Extend operation mode, the FGSW-2022VHP operates on a per-port basis at 10Mbps duplex operation but can provide PoE power output over a distance of up to 250 meters overcoming the 100m limit on Ethernet UTP cable. With this brand- new feature, the FGSW-2022VHP provides an additional solution for 802.3at/bt PoE...
-
Page 8: Features
Easy Installation and Cable Connection As data and power are transmitted over one cable, the FGSW-2022VHP does not need a second cable and electrical outlets on the wall, ceiling or any unreachable place. - Page 9 Smart LCD „ The LCD switch features “Standard”, “VLAN” or “Extend” mode selection; the “Extend” mode features about 45-/20-watt PoE transmission distance of 250m at speed of 10Mbps and VLAN isolation „ The LCD switch is able to isolate ports to prevent broadcast storm and defend DHCP spoofing „...
-
Page 10: Specifications
1.4 Specifications Model FGSD-2022VHP Hardware Specifications 16 10/100BASE-TX RJ45 auto-MDI/MDI-X ports with port-1 to port-16 Copper Ports 2 10/100/1000BASE-T RJ45 auto-MDI/MDI-X ports with port-1 to port-16 2 100/1000BASE-X SFP interfaces with port-19 to SFP/mini-GBIC Slots port-20 4 ports with 802.3bt PoE++ injector function with port-1 to port-4 PoE Injector Port 12 ports with 802.3at PoE+ injector function with port-5... - Page 11 Power Requirements 100~240V AC, 50/60Hz, 5A max. Power Consumption/ Max. 330watts/1132 BTU Dissipation Thermal Fan Contact discharge of ±6KV DC ESD Protection Air discharge of ±8KV DC Surge Protection ±6KV Power over Ethernet IEEE 802.3bt PoE++ PSE (Port 1-4) PoE Standard IEEE 802.3af/at PoE+ PSE (Port 5-16) 802.3bt/UPoE/Legacy (Port 1-4) PoE Power Supply Type...
-
Page 12: Hardware Description
From 550 meters (multi-mode fiber) to 10/20/30/40/50/60/70/120 kilometers (single-mode fiber). „ Smart LCD The Smart LCD that is located on the front panel of the FGSW-2022VHP provides “PoE Management and Status”, “Switch Mode: Standard, VLAN, Extend”, “Budget and Bandwidth Control”, “PD alive check”, “Screen Saver”, “PD Type”,... -
Page 13: Cd Monitor Indicators
2.1.1 CD Monitor Indicators The LCD Switch has an LCD monitor designed for network administrator who can easily obtain real-time per PoE port output watts information and system status display, such as over voltage, low voltage, and PoE chipset over temperature function. -
Page 14: Led Indicators
„ The detailed Smart LCD description of each item is shown below: Parameters Description 30.3W It means the output power port of the PoE switch. (example) It means the port is overloaded corresponding to the PSE, and the port stops powering. It means the port corresponding to the PSE is lightly loaded and the port stops powering (When the current on the network is less than 7.5mA, the PSE thinks the PD has been dialed out and the... -
Page 15: Rear Panel
Indicates the port is successfully established at 1000 Green Lights 1000Mbps. 2.2 Rear Panel The rear panel of the LCD Switch has an AC power socket (100 to 240V AC, 50- 60Hz, 5A). 100-240V , 50/60Hz, 5A max. Figure 2-2: FGSW-2022VHP Switch Rear Panel... -
Page 16: Lcd Management
„ AC Power Receptacle For compatibility with electrical outlet standard in most areas of the world, the LCD Switch’s power supply automatically adjusts to line power in the range of 100-240V AC and 50/60Hz, 2.5/5A. Plug the female end of the power cord firmly into the receptacle on the rear panel of the LCD Switch and the other end into an electrical outlet, and the power will be ready. -
Page 17: Switch Mode
Press the Menu button for about 5 seconds and enter the Main Menu. Choose a menu item by scrolling up and down, and press the “Enter” key to get to the menu item you have chosen. Press the “Back” key to return to the previous menu. 2.3.1 Switch Mode There are three modes -- “Standard”, “VLAN”... - Page 18 Standard Mode (default) > Standard > Standard PoE IP Camera VLAN VLAN Extend Extend Power LCD PoE Switch 100 meters (328 feet) 100BASE-TX UTP with PoE VLAN Isolation Mode IP Camera Ports 1 to 16 Ports 17~20 for Uplink IP Camera Access Denied 1000 Ports 1~16 Access Permitted...
-
Page 19: Budget Control
2.3.2 Budget Control Due to the power allocation strategy of PSE, when the residual power of PoE is too large, the power distribution of the port can be increased as much as possible by increasing the power trimming of the PSE, so that the utilization of the PSE power supply can be improved. -
Page 20: Pse Port Enable
Changing the PoE power-up mode can let non-standard PDs pass the procedures of PoE power delivery process. This way, the switch can supply power to non- standard PDs. The FGSW-2022VHP can be set as UPoE mode, 802.3bt mode or Legacy mode. -
Page 21: Alive Check
2.3.6 Alive Check The FGSW-2022VHP can be configured to monitor connected PD’s status in real time via traffic detection. Once there is no traffic at interval time, the FGSW- 2022VHP is going to restart PoE port power, and bring the PD back to work. It will greatly enhance the reliability and reduce administrator management burden. -
Page 22: Bandwidth Detection
Interval Time Countdown PD Traffic=0 PD ready Startup PD Halt Power Power No traffic! Time(s) Startup Interval Power OFF Figure 2-3: Alive Check Mechanism 2.3.7 Bandwidth Detection When the network transmits “the highest data rate”, more than the set value, over a single port, the switch will set off an alarm to warn the overuse of the bandwidth. -
Page 23: Screen Saver
2.3.9 Screen Saver There are four levels of budget control, namely Always ON, 10min (default), 20min and 30min. 2.3.10 Language There are two languages, namely English and Chinese. 2.3.11 Default Setting Restore the device to default. -
Page 24: Password Setting
2.3.12 Password Setting Set the password to enhance the security level of the LCD Switch. By default, the password function is disabled. If user forgot the password, please refer to the steps to clear the password. 1. Go back to the Switch Port Information page. 2. -
Page 25: Hardware Installation
3. Hardware Installation Start up Please refer to the following for your cabling: 10/100BASE-TX All 10/100BASE-TX ports come with Auto-Negotiation capability. They automatically support 100BASE-TX and 10BASE-T networks. Users only need to plug a working network device into one of the 10/100BASE-TX ports, and then turn on the LCD switch. -
Page 26: Desktop Installation
3.1 Desktop Installation To install the LCD switch on desktop, simply follow the following steps. The switch shown on this page and thereafter is just a representation of the said switch. Step 1: Attach the rubber feet to the recessed areas on the bottom of the LCD switch, as shown in Figure 3-1. -
Page 27: Rack Mounting
3.2 Rack Mounting To install the LCD switch in a 19-inch standard rack, follow the instructions described below. Step 1: Place your LCD switch on a hard flat surface, with the front panel positioned towards you. Step 2: Attach a rack-mount bracket to each side of the LCD switch with supplied screws attached to the package. -
Page 28: Installing The Sfp Transceiver
Figure 3-4: Plugging in the SFP Transceiver „ Approved PLANET SFP Transceivers PLANET LCD Switch supports both single mode and multi-mode SFP transceivers. The following list of approved PLANET SFP transceivers is correct at the time of publication: Gigabit SFP Transceiver Modules „... - Page 29 It is recommended to use PLANET SFP on the LCD switch. If you insert an SFP transceiver that is not supported, the LCD switch will not recognize it. Note 1. Before we connect the LCD switch to the other network device, we have to make sure both sides of the SFP transceivers are with the same media type, for example, 1000BASE-SX to 1000BASE-SX;...
-
Page 30: Product Applications
Never pull out the module without lifting up the lever of the module and turning it to a horizontal position. Directly pulling out the module could damage the module and the SFP module slot of Note the LCD switch. 3.4 Product Applications Department/Workgroup PoE Switch: Providing 16 PoE in-line power interfaces, the LCD switch can easily build a power that centrally controls IP phone system, IP camera system and wireless AP group... -
Page 31: Power Over Ethernet Powered Devices
3.5 Power over Ethernet Powered Devices Voice over IP Phones As many as PoE VoIP phones, ATAs and other Ethernet/ non-Ethernet end-devices can be installed, but UPS is needed for uninterrupted power system and power control 3~5 watts system. Wireless LAN Access Points Access points can readily be installed in museums, sightseeing sites, airports, hotels, campuses, factories and warehouses. -
Page 32: Power Over Ethernet Overview
4. Power over Ethernet Overview What is PoE? PPoE is an abbreviation of Power over Ethernet. The PoE technology means a system safely transmits both power and data on Ethernet UTP cable. The IEEE standard for PoE technology requires Category 5 cable or higher for high power PoE levels, but can operate with Cat3 cable for low power levels. - Page 33 intermediary device between a non-PoE capable switch and a PoE device, it is called a mid-span. An external PoE injector is a mid-span device. Powered Device A powered device (PD) is a device powered by a PSE and thus consumes energy. Examples include wireless access points, IP phones, and IP cameras.
- Page 34 The data pairs are used. Since Ethernet pairs are transformers coupled at each end, it is possible to apply DC power to the center tap of the isolated transformer without upsetting the data transfer. In this mode of operation, the pair on pins 3 and 6 and the pair on pins 1 and 2 can be of either polarity.
-
Page 35: Troubleshooting
5. Troubleshooting This chapter contains information to help you solve issues. If the LCD switch is not functioning properly, make sure the LCD switch was set up according to instructions in this manual. What is the power output of each PoE port? Solution: 1. - Page 36 Why the LCD Switch cannot power on the PoE device Solution: 1. Please check the cable type of the connection from LCD switch to the other end. The cable should be an 8-wire UTP, Category 5 or above and EIA568 cable within 100 meters.