Table of Contents
Advertisement
Quick Links
Trademarks
Copyright © PLANET Technology Corp. 2004.
Contents subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp. All other trade-
marks belong to their respective owners.
Disclaimer
PLANET Technology does not warrant that the hardware will work properly in
all environments and applications, and makes no warranty and representa-
tion, either implied or expressed, with respect to the quality, performance,
merchantability, or fitness for a particular purpose.
PLANET has made every effort to ensure that this User's Manual is accurate;
PLANET disclaims liability for any inaccuracies or omissions that may have
occurred.
Information in this User's Manual is subject to change without notice and does
not represent a commitment on the part of PLANET. PLANET assumes no re-
sponsibility for any inaccuracies that may be contained in this User's Manual.
PLANET makes no commitment to update or keep current the information
in this User's Manual, and reserves the right to make improvements to this
User's Manual and/or to the products described in this User's Manual, at any
time without notice.
If you find information in this manual that is incorrect, misleading, or incom-
plete, we would appreciate your comments and suggestions.
FCC Warning
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment gen-
erates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the Instruction manual, may cause harmful interfer-
ence to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
CE Mark Warning
This is a Class A product. In a domestic environment, this product may cause
radio interference, in which case the user may be required to take adequate
measures.
Revision
PLANET 24-port 10/100Mbps + 2-port Gigabit Ethernet Switch User's Manual
FOR MODEL: FGSW-2620
REV: 1.0 (March.2004)
Part No.: 2010-000032-000
Advertisement
Table of Contents
Related Manuals for Planet FGSW-262
Summary of Contents for Planet FGSW-262
-
Page 1: Fcc Warning
PLANET has made every effort to ensure that this User’s Manual is accurate; PLANET disclaims liability for any inaccuracies or omissions that may have occurred. -
Page 2: Table Of Contents
Table of Contents Chapter 1 Introduction 1.1 Package Contents 1.2 How to Use This Manual 1.3 Product Features 1.4 Product Specifications Chapter 2 Installation 2.1 Product Description 2.1.1 Product Overview 2.2 Installing a Switch Chapter 3 Switch Operation 3.1 Address Table 3.2 Learning 3.3 Forwarding &... -
Page 3: Chapter 1 Introduction
Chapter 1 INTRODUCTION 1.1 Package Contents Check the contents of your package for following parts: ● 24-port 10/100Mbps + 2-port Gigabit Ethernet Switch x1 ● User’s manual x1 ● Power cord x1 ● Two Rack-Mounting Brackets with Attachment Screws x1 If any of these are missing or damaged, please contact your dealer immediately, if possible, retain the carton including the original packing material, and use them against to repack the product in case there is a need return to it to us for repairing. -
Page 4: Product Features
1.3 Product Features ● Comply with IEEE802.3, IEEE802.3u 10/100Base-TX, IEEE802.3ab 1000Base- T Ethernet Standard ● 24 (10/100Mbps), 2 (10/100/1000Mbps) Gigabit Ethernet Switch ● Each Switching Fast Ethernet ports support auto-negotiation-10/20, 100/ 200Mbps,supported ● Each Switching Gigabit ports support auto-negotiation- 10/20,100/200Mbps, 1000/2000Mbps supported ●... -
Page 5: Product Specifications
1.4 Product Specifications Model FGSW-2620 Hardware Specification Ports 24 10/ 100Base-TX RJ-45 Auto-MDI/MDI-X ports Gigabit ports 2 10/100/1000Base-T RJ-45 Auto-MDI/MDI-X ports Switch architecture Store-and-forward Switch Fabric 8.8Gbps Throughput (packet 6.547Mpps per second) Address Table 8K entries Share data Buffer 2.5Mbit Back pressure for half duplex, IEEE 802.3x Pause Flow Control Frame for full duplex... - Page 6 This page is intentionally left blank...
-
Page 7: Chapter 2 Installation
2.1 Product Description The PLANET FGSW-2620 provides 24 10/100Mbps Fast Ethernet ports and 2 10/100/ 1000Mbps Gigabit Ethernet ports. The two Gigabit Ethernet ports support 10/100/ 1000Mbps as well as half/full mode by auto-negotiation and can be easily connected to corporate backbones and servers. -
Page 8: Installing A Switch
1. The device is a power-required device, it means, it will not work till it is powered. If your networks should active all the time, please consider using UPS (Uninterrupted Power Supply) for your device. It will prevent you from network data loss or network downtime. -
Page 9: Rack Mounting
presented. To install your Switch on a desktop or shelf, simply complete the following steps. 2.2.1 Desktop Installation To install a Switch on a desktop or shelf, simply complete the following steps: Step1: Attach the rubber feet to the recessed areas on the bottom of the Switch. Step2: Place the Switch on a desktop or shelf near an AC power source. - Page 10 Figure 2-3 Attaching the brackets to the FGSW-2620 Caution: You must use the screws supplied with the mounting brackets. Damage caused to the parts by using incorrect screws would invalidate your warranty. Step3: Secure the brackets tightly. Step4: Follow the same steps to attach the second bracket to the opposite side. Step5: After the brackets are attached to the switch, use suitable screws to se- curely attach the brackets to the rack, as shown in Figure 2-4.
-
Page 11: Chapter 3 Switch Operation
Chapter 3 SWITCH OPERATION 3.1 Address Table The Switch is implemented with an address table. This address table composed of many entries. Each entry is used to store the address information of some node in network, including MAC address, port no, etc. This information comes from the learning process of Ethernet Switch. -
Page 12: Auto-Negotiation
The Switch performs “Store and forward” therefore, no error packets occur. More reliably, it reduces the re-transmission rate. No packet loss will occur. 3.5 Auto-Negotiation The STP ports on the Switch have built-in “Auto-negotiation”. This technology automatically sets the best possible bandwidth when a connection is established with another network device (usually at Power On or Reset). -
Page 13: Chapter 4 Troubleshooting
Chapter 4 TROUBLESHOOTING This chapter contains information to help you solve problems. If the Ethernet Switch is not functioning properly, make sure the Ethernet Switch was set up according to instructions in this manual. The LNK LED is not lit Solution: Check the cable connection and its quality Some stations cannot talk to other stations located on the other port... - Page 14 This page is intentionally left blank...
-
Page 15: Switch's Rj-45 Pin Assignments
Appendix A A.1 Switch‘s RJ-45 Pin Assignments 1000Mbps, 1000Base T Contact MDI-X BI_DA+ BI_DB+ BI_DA- BI_DB- BI_DB+ BI_DA+ BI_DC+ BI_DD+ BI_DC- BI_DD- BI_DB- BI_DA- BI_DD+ BI_DC+ BI_DD- BI_DC- Implicit implementation of the crossover function within a twisted-pair cable, or at a wiring panel, while not expressly forbidden, is beyond the scope of this standard. - Page 16 The standard cable, RJ-45 pin assignment The standard RJ-45 receptacle/connector There are 8 wires on a standard UTP/STP cable and each wire is color-coded. The following shows the pin allocation and color of straight cable and crossover cable connection: Figure A-1: Straight-Through and Crossover Cable Please make sure your connected cables are with same pin assignment and color as above picture before deploying the cables into your network.
- Page 18 Part No.:2010-000032-000...