Related Manuals for Planet FGSW-1828PS
Summary of Contents for Planet FGSW-1828PS
- Page 1 User's Manual FNSW-1608PS FGSW-1828PS 16-Port 10/100Mbps Web Smart PoE Switch - 1 -...
-
Page 2: Fcc Warning
Trademarks Copyright © PLANET Technology Corp. 2008. Contents subject to revision without prior notice. PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective owners. Disclaimer PLANET Technology does not warrant that the hardware will work properly in all environments and applications, and makes no warranty and representation, either implied or expressed, with respect to the quality, performance, merchantability, or fitness for a particular purpose. -
Page 3: Table Of Contents
3.2 M ... 11 ANAGEMENT ETHOD 3.2.1 Web Management... 11 3.2.2 PLANET Smart Discovery Utility... 12 3.3 L FNSW-1608PS / FGSW-1828PS ... 13 OGGING ON TO THE 4. WEB MANAGEMENT... 14 4.1 L ... 14 OGIN IN TO THE WITCH 4-2 S ... - Page 4 5.5 A ... 63 EGOTIATION 6. POWER OVER ETHERNET OVERVIEW... 64 7. THE POE PROVISION PROCESS ... 66 7.1 L ... 66 ETECTION 7.2 C ... 66 LASSIFICATION 7.3 S ... 67 TART 7.4 O ... 67 PERATION 7.5 P OWER ISCONNECTION CENARIOS...
-
Page 5: Introduction
TCP & UDP filter and IGMP Snooping v1/v2. Also the PoE Setting, such as PoE power Disable/Enable and PoE power consumption monitoring The FGSW-1828PS also provide two Gigabit Ethernet ports, either TP or SFP per port. The two Gigabit ports either can be 1000Base-T for 10/100/1000Mbps or 1000Base-SX/LX through SFP (Small Factor Pluggable) interfaces. The distance can be extended from 100 meters (TP), 550 meters (Multi-mode fiber), up to above 10/20/30/40/50/70/120 kilometers (Single-mode fiber). -
Page 6: Features
◆ 16-Port 10/100Mbps with 8-Port PoE Web Smart PoE Switch (FNSW-1608PS) ◆ 16-Port 10/100Mbps + 2 Gigabit TP / SFP Combo Web Smart PoE Switch ◆ 8-Port support 48VDC power to PoE Powered Device (Port 1 to port 8) ◆... - Page 7 Dimensions Weight Power Requirement System operation Power Con- sumption / Dissipation (Full load) Temperature Humidity Operating: Power over Ethernet PoE Standard PoE Power Supply Type PoE Power Output Power Pin Assignment Power Budge Smart function System Configuration Alert Trap Port configuration Bandwidth Control Broadcast Storm Control Port Statistics...
-
Page 8: Hardware Description
The Front Panel of the Web Smart PoE Switch consists of 16 Auto-Sensing 10/100Mbps Ethernet RJ-45 Ports, Also the FGSW-1828PS provides 2 Gigabit TP/SFP combo ports either can be 1000Base-T for 10/100/1000Mbps or 1000Base-SX/LX through SFP (Small Factor Pluggable) interface. -
Page 9: Rear Panel
2.2 Rear Panel The rear panel of the Web Smart PoE Switch indicates an AC inlet power socket, which accepts input power from 100 to 240VAC, 50-60Hz, 1A. Figure 2-3: FNSW-1608PS / FGSW-1828PS Switch rear panel Power Notice: 1. The device is a power-required device, it means, it will not work till it is powered. If your networks should active all the time, please consider using UPS (Uninterrupted Power Supply) for your device. - Page 10 To install the Web Smart PoE Switch in a 19-inch standard rack, follow the instructions described below. Step 1: Place your Web Smart PoE Switch on a hard flat surface, with the front panel positioned towards your front side. Step 2: Attach a rack-mount bracket to each side of the Web Smart PoE Switch with supplied screws attached to the package.
-
Page 11: Switch Management
Web browser, such as Microsoft Internet Explorer, Netscape Navigator or Mozilla Firefox. The following shows how to startup the Web Management of the Switch, please note the Web Smart PoE Switch is con- figured through an Ethernet connection, make sure the manager PC must be set on the same IP subnet address, for example, the default IP address of the Switch is 192.168.0.100 (the factory-default IP address), then the manager PC... -
Page 12: Planet Smart Discovery Utility
Using this management method: The Web Smart PoE Switch must have an Internet Protocol (IP) address accessible for the remote host. For easily list the FNSW-1608PS / FGSW-1828PS in your Ethernet environment, the Planet Smart Discovery Utility from user’s manual CD-ROM is an ideal solution. -
Page 13: Logging On To The Fnsw-1608Ps / Fgsw-1828Ps
8. Press “Exit” button to shutdown the planet Smart Discovery Utility. 3.3 Logging on to the FNSW-1608PS / FGSW-1828PS When you log on to the Web Smart PoE Switch Web interface for the first time, a sign-on string appears and you are prompted for a Web login username and password. -
Page 14: Web Management
To modify your PC’s IP domain to the same with Web Smart PoE Switch then use the default IP address (192.168.0.100) to remote configure Web Smart PoE Switch through the Web interface. The following section will base on the console screens of FGSW-1828PS, for FNSW-1608PS the Notice: display will be the same to FGSW-1828PS. - Page 15 The Switch Menu provide eight major management functions, the screen in These items and its description shown as below: System: Provide System configuration of Web Smart PoE Switch. ◆ Port Management: Provide Port Management configuration of Web Smart PoE Switch.
-
Page 16: System
4-2 System This section provides System Information, IP Configuration, Password Setting, Alert Trap, Factory Default, Firmware Update and Reboot functions of Web Smart PoE Switch, the screen in System object of Web Smart PoE Switch. Object System Information Display the MAC address, Hardware Version, and Software Version, Device Description. -
Page 17: System Information
4.2.1 System Information This section displays the MAC address, Hardware Version, Software Version and System Up Time, also allow define the device description and press “Apply” button to take affect. The screen in Figure 4-4 appears. Figure 4-4 System Information Web Page Screen Up to 16 characters is allowed for the Device Description. -
Page 18: Ip Configuration
After setup complete and press “Apply” button to take affect. The following screen in Web page login screen with new IP address will show up. After input correct username and password then can continue the Web Smart PoE Switch management. Figure 4-5 IP Configuration Web Page Screen... -
Page 19: Password Setting
4.2.3 Password Setting This section provides change the Username and Password, the screen in Figure 4-7 appears. Figure 4-7 Password Setting Web Page Screen Up to 8 characters is allowed for the username and password assign. Notice: - 19 -... -
Page 20: Alert Trap
4.2.4 Alert Trap This section provides Web Smart PoE Switch Alert Trap configuration, such as Disable or enable the trap mode and alert IP address assign the screen in Figure 4-8 Switch. Object Trap mode Allow disable or enable the Alert Trap mode. -
Page 21: Factory Default
4.2.5 Factory Default This section provides reset the Web Smart PoE Switch to factory default mode, the screen in Figure 4-9 appears. Figure 4-9 Factory Default Web Page Screen Press “Factory Default” button to take affect. The following screen in... -
Page 22: Firmware Update
4.2.6 Firmware Update This section provides firmware upgrade of the Web Smart PoE Switch, the screen in Figure 4-11 appears. Figure 4-11 Firmware Update Web Page Screen ress “Update” button for start the firmware upgrade process, the screen in Figure 4-12 & 4-13 appears. - Page 23 Figure 4-13 Firmware Update Web page Screen Then the following screen appears, press “Browser” button to find the firmware locati on administrator PC, the screen in Figure 4-14 appears. Figure 4-14 Firmware Update Web Page Screen - 23 -...
- Page 24 After device reboot then can use the latest firmware of the Web Smart PoE Switch. Figure 4-16 Firmware Update Web Page Screen...
-
Page 25: Reboot
Web Smart PoE Switch, the screen in Figure 4-17 appears. Figure 4-17 Reboot Web Page Screen ress “Reboot” button to reboot the Web Smart PoE Switch, the screen in Figure 4-18 appears. After device reboot completed, the Web login screen appears and login for further management. -
Page 26: Port Management
Bandwidth Control Allow to configure bandwidth control of each port from Web Smart PoE Switch. in section 4.3.3. Broadcast Storm Control Allow to configure broadcast storm control of each port from Web Smart PoE Switch. plained in section 4.3.4. Port Statistics Display each port statistics of Web Smart PoE Switch. -
Page 27: Port Configuration
.1 Port Conf iguration s section introduces d etail s ettings of per port on Web Smart PoE Switch; the screen in Figure 4-20 & 4-21 appears and table 4-4 & 4-5 descriptions th e Port Configuratio n objects of Web Smart PoE Switch. - Page 28 Port Allow choosing all or one port of Web Smart PoE Switch for further management, the available options is All & 01 to 16 (FNSW-1608PS). Or All & 01 to 18 (FGSW-1828PS). Speed Mode Allow choosing various speed duplex mode from one specific port of Web Smart PoE...
-
Page 29: Port Mirroring
4.3.2 Port Mirroring s secti on introduces detail s ettings of Port Mirroring function of Web Smart PoE Switch; the screen in ears and table descript ions the Port Mirroring objects of Web Smart PoE Switch. Object Monitored Packets Provide disable and enable the Port Mirroring function, the available options are Disable, RX, TX, TX &... -
Page 30: Bandwidth Control
4.3.3 Bandwidth Control This section introduces detail settings of Bandwidth Control function of Web Smart PoE Switch; the screen in appears and table 4-7 description the Bandwidth Control objects of Web Smart PoE Switch. Object Port Indicate port 1 to port 16 of Web Smart PoE Switch. -
Page 31: Broadcast Storm Control
4.3.4 Broadcast Storm Control This section introduces detail settings of Broadcast Storm Control function of Web Smart PoE Switch; the screen in 4-24 appears and table 4-8 descriptions the Broadcast Storm Control objects of Web Smart PoE Switch. Object Filter Mode Provide 5%, 10%, 25%, 50%, Disable different filter mode. -
Page 32: Port Statistics
Drop Packet & Receive Packet CRC error Packet & Receive Packet Default mode is Receive Packet & Transmit Packet. Port Indicate port 1 to port 16 (FNSW-1608PS), port 1 to port 18 (FGSW-1828PS). Transmit Display Transmit count value from each port. Receive Display Receive count value from each port. -
Page 33: Vlan Setting
Port-based VLAN Port-based VLAN limit traffic that flows into and out of switch ports. Thus, all devices connected to a port are members of the VLAN(s) the port belongs to, whether there is a single computer directly connected to a switch, or an entire department. - Page 34 Tag-aware switches must keep a table to relate PVID within the switch to VID on the network. The switch will compare the VID of a packet to be transmitted to the VID of the port that is to transmit the packet. If the two VID are different the switch will drop the packet.
- Page 35 This section provides VLAN Configuration from Web Smart PoE Switch, the screen in 4-10 describes the VLAN Setting object of Web Smart PoE Switch. Object VLAN Mode Provide different VLAN operation mode, the available options are shown as below: No VLAN 802.1Q VLAN.
-
Page 36: 802.1Q Vlan
.4.1 802.1Q VLAN This section introduces detail information of IEEE 802.1Q VLAN function of Web Smart PoE Switch; Choose “802.1Q VLAN” from VLAN from the VLAN Mode and press “Apply” button to enable the 802.1Q VLAN function. The screen in Figure 4-27 &... - Page 37 Assign and display different VLAN name from multi-802.1Q VLAN groups. Up to maximum 8 char- acters allow. Port Indicate port 1 to port 16 (FNSW-1608PS), port 1 to port 18 (FGSW-1828PS). Member Allow to click specific port as member port from different 802.1Q VLAN groups.
-
Page 38: Q Vlan Setting Example
The scenario described as follow: Untagged packet entering VLAN 2 While [PC-1] transmit an untagged packet enters Port-1, the Web Smart PoE Switch. Will tag it with a VLAN Tag=2. [PC-2] and [PC-3] will received the packet through Port-2 and Port-3. - Page 39 Setup steps 1. Create VLAN Group: Set VLAN Group 1 = default-VLAN with VID (VLAN ID) =1. Add two VLANs – VLAN 2 and VLAN 3, VLAN Group 2 with VID=2, VLAN Group 3 with VID=3. Figure 4-31 Add new VLAN Group Screen - 39 -...
- Page 40 2. Assign VLAN Member : VLAN 2 : Port-1,Port-2 and Port-3. VLAN 3 : Port-4, Port-5 and Port-6. VLAN 1: All other ports – Port-7~Port-18. Figure 4-32 Assign VLAN members for VLAN 2 and VLAN 3 Please remember to remove the Port 1 – Port 6 from VLAN 1 membership, since the Port 1 – Port 6 had been assigned to VLAN 2 and VLAN 3.
- Page 41 Its import to remove the VLAN member port from VLAN 1 group. Or the ports would become overlap- Notice: ping setting. 3. Assign PVID for each port: Port-1,Port-2 and Port-3 : PVID=2. Port-4,Port-5 and Port-6 : PVID=3. Port-7~Port-18: PVID=1. 4. Enable VLAN Tag for specific ports Link Type: Port-3 (VLAN-2) and Port-6 (VLAN-3).
- Page 42 Figure 4-35 A Server connect to the VLAN overlapping area Specify Port-7 on the Web Smart PoE Switch that connects to the server. Assign Port-7 to both VLAN 2 and VLAN 3 at the VLAN Member configuration page. The screen in appears.
- Page 43 Define a VLAN 1 as a “Public Area” that overlapping with both VLAN 2 members and VLAN 3 members. Figure 4-37 VLAN 1 – The public area member assign Setup Port-7 with “PVID=1” at VLAN per Port Configuration page. The screen in Figure 4-38 appears.
- Page 44 Figure 4-38 Setup Port-7 with PVID-1 Although the VLAN 2 members: Port-1 to Po rt-3 and VLAN 3 members: Port-4 to Port -6 also belongs to VLAN 1. But with different PVID settings, packets form VLAN 2 or VLAN 3 is not able to access to the other VLAN. - 44 -...
-
Page 45: Port Based Vlan
4.4.2 Port Based VLAN This section introduces detail information of Port Based VLAN function of Web Smart PoE Switch; Choose “Port Based VLAN” from VLAN from the VLAN Mode and press “Apply” button to enable the port based VLAN function. The screen in Figure 4-39 &... -
Page 46: Port Based Vlan Setting Example
Assign and display different VLAN name from multi-port based VLAN groups. Up to maximum 8 characters allow. Port Indicate port 1 to port 16 (FNSW-1608PS), port 1 to port 18 (FGSW-1828PS). Member Allow to click specific port as member port from different port based VLAN groups. -
Page 47: Mtu Vlan
Member Port Indicate the Member Port of Web Smart PoE Switch. Apply button Press this button for save current configuration of Web Smart PoE Switch. Table 4-15 Descriptions of the MTU VLAN Setting Screen Objects function of We b Smart PoE Switch; Choose “MTU” from VLAN... -
Page 48: Trunk Setting
Port link aggregations can be used to increase the bandwidth of a network connection or to ensure fault recovery. Link aggregation lets you group up to 4 consecutive ports into a single dedicated connection between any two the Switch or other Layer 2 switches. - Page 49 Indicate the Trunk Member Port 5,6,7,8 of Web Smart PoE Switch. Apply Press this button for save current configuration of Web Smart PoE Switch. Table 4-16 Descriptions of the Trunk Setting Screen Objects Figure 4-42 Trunk Setting Web Page Screen...
-
Page 50: Qos Setting
QoS reduces bandwidth limitations, delay, loss, and jitter. It also provides increased reliability for delivery of your data and allows you to prioritize certain applications across your network. You can define exactly how you want the switch to treat selected applications and types of traffic. -
Page 51: Priority Mode
4.6.1 Priority Mode This section introduces detail information of Priority Mode of Web Smart PoE Switch; the screen in table 4-18 descriptions the Priority Mode of Web Smart PoE Switch. Object Priority Mode Provide three different Priority polices on Web Smart PoE Switch, the available options are... -
Page 52: Class Of Service Configuration
Object Enable High Priority Allow to disable or Port Indicate port 1 to port 16 (FNSW-1608PS), port 1 to port 18 (FGSW-1828PS). Port Base Define per port Class of Service polic VLAN Tag Define per port Class of Service policy based on VLAN Tag priority policy. -
Page 53: Tcp / Udp Port Based Qos
4.6.3 TCP / UDP Port Based QoS This section introduces detail information of TCP / UDP Port Based QoS Configuration of Web Smart PoE Switch; the screen in Figure 4-46 & 4-47 appears and Smart PoE Switch. Figure 4-46 TCP / UDP Port Based QoS Configuration Web Page Screen... - Page 54 Allow to choose “Override” or “Not Override” options. Default mode is Not Override . Apply Press this button for save current configuration of Web Smart PoE Switch. Table 4-20 Descriptions of the TCP / UDP Port Based QoS Configuration Screen Objects...
-
Page 55: Security Filter
Allow define three MAC Address on per port of 4.7.1. TCP/UDP Filter Allow define the filter policy of TCP / UDP flow on Web Smart PoE Switch. 4.7.2. Table 4-21 Descriptions of the Security Filter W Figure 4-48 Security Filter Web Page Screen Description Web Smart PoE Switch. -
Page 56: Mac Address Filter
MAC Address Allow to input three MAC Address on per port of Web Smart PoE Switch. Select Port Allow to select port 1 to port 16 (FNSW-1608PS), port 1 to port 18 (FGSW-1828PS). Binding Allow to Disable or Enable the binding function on each port of Web Smart PoE Sw Apply Press this button for save current configuration of Web Smart PoE Switch. -
Page 57: Tcp / Udp Filter
4.7.2 TCP / UDP Filter This section introduces detail information of TCP / UDP Filter of Web Smart PoE Switch; the screen in Figure 4-50 appea table 4-24 descriptions the TCP / UDP Filter Configuration of Web Smart PoE Switch. - Page 58 User_Define_b User_Define_c User_Define_d Secure Egress Port Indicate port 1 to port 16 (FNSW-1608PS), port 1 to port 18 (FGSW-1828PS).Click specific port for filtering. Apply Press this button for save current configuration of Web Smart PoE Switch. Table 4-24 Descriptions of the TCP / UDP Filter Configuration Screen Objects...
-
Page 59: Misc Operation
Allow Disable or Enable the VLAN Striding function of Web Smart PoE Switch. Default mode is Disable. IGMP Snooping V1 & V2 Allow Disable or Enable the IGMP Snooping V1 & V2 function of Web Smart PoE Switch. Default mode is Disable. Apply Press this button for save current configuration of Web Smart PoE Switch. -
Page 60: Poe Setting
.When this value is exceeded, ports will be deactivated, according to user-defined priorities. The power budget is managed according to the following user-definable parameters: maximum available power, ports priority, maximum allowable power per port. This function provides PoE setting of Web Smart PoE Switch; the screen in Figure 4-52 appears and... - Page 61 Port Priority Deliver PoE power by port priority setting Total Limit. Set limit value of the total POE port provided power to the PDs. For Web Smart PoE Switch, the total PoE power reservation from Port-1~8 is up to 110 watts Power reservation Show the total watts usage of Web Smart PoE Switch.
-
Page 62: Logout
4-10 Logout This section provide logout function on Web Smart PoE Switch, after choose this function and the fol lowing screen appears in Figure 4-53 & 4-54 . Please press “Logout” button to take effect and Login W eb Screen appears. Please re-login the Web Smart PoE Sw itch for further management. -
Page 63: Switch Operation
5.2 Learning When one packet comes in from any port. The Switch will record the source address, port no. And the other related information in address table. This information will be used to decide either forwarding or filtering for future packets. -
Page 64: Power Over Ethernet Overview
Figure 1 - Power Supplied over the Spare Pins 6. POWER OVER for wired Ethernet, the most widely installed local area n legacy switch and the powered device. Mid-Span is tap the unused wire pairs 4/5 ETHERNET OVERVIEW - 64 -... - Page 65 The data pairs are used. Since Ethernet pairs are tra nsformer coupled at each end, it is possible to apply DC power to the center tap of the isolation transformer without upsetti ng the data transfer. In this mode of operation the pair on pins 3 and 6 and the pair on pins 1 and 2 can be of either polarity.
-
Page 66: The Poe Provision Process
While adding PoE support to networked devices is relatively painless, it should be realized that power cannot simply be transferred over existing CAT-5 cables. Without proper preparation, doing so may result in damage to devices that are not designed to support provision of power over their network interfaces. The PSE is the manager of the PoE process. -
Page 67: Start-Up
7.3 Start-up Once line detection and optional classification stages are completed, the PSE must switch from low voltage to its full voltage capacity (44-57 Volts) over a minimal amount of time (above 15 microseconds). A gradual startup is required, as a sudden rise in voltage (reaching hig lines. -
Page 68: Troubleshooting
Please check the VLAN, port trunking function that may introduce this kind of problem. Performance is bad Solution: Check the full duplex status of the Ethernet Switch. If the Ethernet Switch is set to full duplex and the partner is set to half duplex, then the performance will be poor. -
Page 69: Appendix A Networking Connection
A.1 Switch‘s RJ-45 Pin Assignments 1000Mbps, 1000Base Contact BI_DA+ BI_DA- BI_DB+ BI_DC+ BI_DC- BI_DB- BI_DD+ BI_DD- 10/100Mbps, 10/100Base-TX RJ-45 Connector pin assignment Contact Media Dependant Interface Tx + (transmit) Tx - (transmit) Rx + (receive) 4, 5 Rx - (receive) 7, 8 A.2 RJ-45 cable pin assignment... - Page 70 There are 8 wires on a standard UTP/STP ca and color of straight cable and crossover cable Straight Cable Straight Cable Figure Please make sure your connected cables are with same cables into r network. 2080-A31120-006 ble and each wire is color-coded. The following shows the pin allocation connection: 1 = White / Orange 2 = Orange...
-
Page 71: Ec Declaration Of Conformity
EC Declaration of Conformity For the following equipment: *Type of Product: 16-Port 10/100Base-TX + 2G TP/SFP Combo Web Smart PoE Switch *Model Number: FGSW-1828PS * Produced by: Manufacturer‘s Name : Manufacturer‘s Address: is herewith confirmed to comply with the requirements set out in the Council Directive on the Approximation of the Laws of the Member States relating to Electromagnetic Compatibility Directive on (89/336/EEC,92/31/EEC,93/68/EEC). - Page 72 EC Declaration of Conformity For the following equipment: *Type of Product : 16-Port 10/100Mbps / 8-Port PoE Web Smart Ethernet Switch *Model Number FNSW-1608PS * Produced by: Manufacturer‘s Name : Manufacturer‘s Address: is herewith confirmed to comply with the requirements set out in the Council Directive on the Approximation of the Laws of the Member States relating to Electromagnetic Compatibility Directive on (89/336/EEC,92/31/EEC,93/68/EEC).