Table of Contents
Advertisement
maintenance
Maintenance Instructions
1. Always turn off the gas valve before cleaning.
For relighting, refer to lighting instructions. Keep
the burner and control compartment clean by
brushing and vacuuming at least once a year.
When cleaning the logs, use a soft clean paint
brush as the logs are fragile and easily damaged.
2. Clean appliance and door with a damp cloth
(never when unit is hot). Never use an abrasive
cleaner. The glass should be cleaned with a gas
fireplace glass cleaner. The glass should be
cleaned when it starts looking cloudy.
3. The heater is finished in a heat resistant
paint and should only be refinished with heat
resistant paint. Excalibur
®
Paint - Metallic Black #6309.
4. Make a periodic check of burner for proper
position and condition. Visually check the flame
of the burner periodically, making sure the flames
are steady; not lifting or floating. If there is a
problem, call a qualified service person.
5. The appliance and venting system must be
inspected before use, and at least annually, by
a qualified field service person, to ensure that
the flow of combustion and ventilation air is not
obstructed.
Note: Never operate the appliance without
the glass properly secured in place.
6. Do not use this appliance if any part has been
under water. Immediately call a qualified service
technician to inspect the appliance and to
replace any part of the control system and any
gas control which has been under water.
7. Verify operation after servicing.
General Vent Maintenance
Conduct an inspection of the venting system semi-
annually. Recommended areas to inspect as follows:
1. Check the Venting System for corrosion in areas
that are exposed to the elements. These will
appear as rust spots or streaks, and in extreme
cases, holes. These components should be
replaced immediately.
2. Remove the Cap, and shine a flashlight down
the Vent. Remove any bird nests, or other foreign
material.
|
58
Regency Excalibur
3. Check for evidences of excessive condensation,
such as water droplets forming in the inner
liner, and subsequently dripping out the joints,
Continuous condensation can cause corrosion
of caps, pipe, and fittings. It may be caused
by having excessive lateral runs, too many
elbows, and exterior portions of the system
being exposed to cold weather.
4. Inspect joints, to verify that no pipe sections or
fittings have been disturbed, and consequently
loosened. Also check mechanical supports such
as Wall Straps, or plumbers' tape for rigidity.
Log Replacement
The unit should never be used with broken logs. Turn
off the gas valve and allow the unit to cool before
uses StoveBright
opening door and carefully remove the logs. (The
pilot light generates enough heat to burn someone.)
If for any reason a log should need replacement, you
must use the proper replacement log. The position
of these logs must be as shown in the diagrams
under Log Installation.
Note: Improper positioning of logs may
create carbon build-up and will
severely alter the unit's performance
which is not covered under warranty.
Glass Gasket
If the glass gasket requires replacement use a
tadpole glass gasket (Part # 936-155).
Door Glass
Your Excalibur
temperature, 5 mm Neoceram ceramic glass that will
withstand the highest heat that your unit will produce.
If your glass requires cleaning, we recommend
using an approved glass cleaner available at all
authorized dealers. Do not use abrasive materials.
Do not clean the glass when hot.
In the event that you break your glass by impact,
purchase your replacement from an authorized
Excalibur
instructions for replacement.
WARNING: Do not operate the appliance
with the glass panels removed, cracked or
broken. Replacement of the glass panels
should be done by a licensed or qualified
service person.
Caution: Wear gloves when removing
damaged or broken glass.
P90E-11 Direct Vent Gas Stove
®
fireplace is supplied with high
®
dealer only, and follow our step-by-step
®
Glass Replacement
Remove the glass door front (Refer to the "Glass
Door Installation" section). Remove the 4 glass clips
from each corner. Slide in the new replacement
glass. Push the 4 glass clips back onto the frame.
The glass must have gasketing around it.
Advertisement
Table of Contents
