Siemens 6DR55 Series Manual page 100

Operation
■
SIPART PS2 PA configurations (PROFIBUS version)
Parameter- Function
name
1. YFCT Type of actuator:
part-turn/linear
- Part-turn actuator
- Linear actuator
- Linear actuator without
sine-wave correction
- Part-turn actuator with
NCS
- Part-turn actuator with
NCS, reverse direction
- Linear actuator with NCS
1)
2. YAGL Rated angle of feedback
2)
3. YWAY Travel range 5 to 130 mm
(0.20 to 5.12 inch)
- None
- Short lever 33°
- Short lever 90°
- Long lever 90°
4. INITA Initialization (automatic
commissioning)
5. INITM Initialization (manual
commissioning)
6. SDIR Setpoint direction rising
Setpoint direction falling
7. TSI Setpoint ramp OPEN
8. TSD Setpoint ramp CLOSED
9. SFCT Setpoint function
- Linear
- Equal percentage
- Equal percentage, reversed
- Freely adjustable
3)
10. SL0 Setpoint interpolation points
. with free characteristic
. 0 %, 5 %, 10 % ... 100 %
30. SL20
31. DEBA Controller dead zone
32. YA Start of manipulated variable
limit
33. YE End of manipulated variable
limit
34. YNRM Manipulated variable scaling
mech. travel/flow
35. YCLS "Tight shut-off" with man. var.
- None
- Only up
- Only down
- Up and down
36. YCDO Value for "tight shut-off", down
37. YCUP Value for "tight shut-off", up
4)
38. BIN1 Function of binary input 1
None
NO
Only signal
Block configuring
Block config. and manual
Drive valve to ye
Drive valve to ya
Block movement
NC
Only signal
Drive valve to ye
Drive valve to ya
Figure 59 Parameter table of the positioner
Block movement
98
Parameter values Dimen-
sion
turn
WAY
LWAY
ncST
-ncST
ncSL
90 ° De-
33 ° grees
OFF
5/10/15/20 mm
25/30/35
40/50/60/70/90/
110/130
no
###.#
Strt
FINISH
no
###.#
Strt
FINISH
riSE
FALL
Auto
0 to 400 s
0 to 400 s
Lin
1-25, 1-33, 1-50
n1-25, n1-33,
n1-50
FrEE
0.0 to 100.0 %
Auto
0.1 to 10.0 %
0.0 to 100.0 %
0.0 to 100.0 %
MPOS
FLOW
no
uP:
do
uP do
0.0 to 100.0 %
0.0 to 100.0 %
OFF
on
bLoc1
bLoc2
uP
doWn
StoP
-on
-uP
-doWn
-StoP
Parameter- Function
name
4)
39. BIN2 Function of binary input 2
None
NO
Only signal
Drive valve to ye
Drive valve to ya
Block movement
NC
Only signal
Drive valve to ye
Drive valve to ya
Block movement
5)
40. AFCT Alarm function
None
min : max: normal
inverted
min : min: normal
inverted
max : max: normal
inverted
41. A1 Response threshold for alarm 1
42. A2 Response threshold for alarm 2
5)
43. FCT Function of alarm output
Fault:
normal
inverted
Fault + not Automatic:
normal
inverted
Fault + not Automatic + BI:
normal
inverted
(+ means logical OR
operation)
44. TIM Monitoring time for setting of
fault signal "Control devia-
tion"
45. LIM Response threshold of fault
signal "Control deviation"
46. STRK Limit for travel integral
47. DCHG Limit for change in direction
48. ZERO Limit for zero limit monitoring
49. OPEN Limit for open limit monitor-
ing
50. DEBA Limit for dead zone monitor-
ing
51. PRST Preset (factory setting)
52. FSTY Safety setting:
Parameterized safety
setpoint
Last setpoint
Open exhaust air valve
53. FSTI Monitoring time for setting of
safety position
54. FSVL Safety setpoint
55. STNR Station number
56. IDENT Device mode (Ident No.)
- Multi-vendor
- Full functionality
1
) Parameter only visible with "turn" or "WAY"; if "turn" is selected,
33 ° cannot be set.
2
) Parameter not visible if 1. YFCT = "turn", "LWAY" or "-ncST"
has been selected.
3
) Interpolation points only appear if 9.SFCT=FrEE has been selected.
4
) NC means: action with opened switch or Low level.
NO means: action with closed switch or High level.
5
) Normal means: High level without fault.
Inverted means: Low level without fault.
Parameter values
OFF
on
uP
doWn
StoP
-on
-uP
-doWn
-StoP
oFF
Mi:MA
Mi:MA
Mi:Mi
Mi:Mi
MA:MA
MA:MA
0.0 to 100.0
0.0 to 100.0
-
nA
- nA
nAb
- nAb
Auto
0 to 100
Auto
0.0 to 100.0
0 to 1.00E9
OFF
1 to 1.00E9
OFF
0.0 to 100.0
OFF
0.0 to 100.0
OFF
0.0 to 10.0
no
Strt
oCAY
FSVL
FSSP
FSAC
0 to 100
0 to 100.0
0 to 126
0
1
SIPART PS2 PA Manual
A5E00127926--05
Dimen-
sion
%
%
s
%
%
%
%
s
%