Specifications; Regulatory Information - Interlogix Simon XT Installation Instructions Manual

screen. To speed up the process, stay in
Programming. This keeps the panel in
high-speed communication mode with the
touch screens.
2
-- Z-Wave Used to add, remove, and troubleshoot Z-
Wave devices and networks. To control Z-
Wave devices via the Alarm.com website
and smart phone apps, you will also need
to enable Z-Wave services on the account.
2
--- Add Device Add Z-Wave devices to the module's
network. Make sure the device you are
trying to add is powered up and within 3
to 6 feet of the Simon XTi panel. Read the
manufacturer's instructions on what
button to press on the device to enroll it.
2
--- Remove Device Remove an existing Z-Wave device, or to
"reset" a Z-Wave device that was
previously learned into a different Z-Wave
network, before you can learn it into the
CDMA module.
---Update 2WTTS Press Update 2WTTS to force an update of
the thermostat, lights or locks information
shown on the touch screen (2WTTS). Note
that these updates may take several
minutes to complete.
----Thermostats View thermostat data and update/remove
thermostats from display on the panel
and touch screens.
----Lights Update the lights list shown on the panel
and touch screens.
----Locks Update locks list shown on panel and
touch screens and pair locks with their
door contact sensor.
2
--- Advanced Provides additional functionality for
advanced Z-Wave troubleshooting and
configuration.
2
---- Rediscovery Network rediscovery allows the system to
determine the most efficient
communication patch between Z-Wave
devices. (During this process the Z-Wave
network is busy and cannot respond to
other commands.)
2
---- Replicate Mode Initiates replicate mode on the panel.
2
---- Send Node Info For advanced use only. Do not use unless
directed to do so by Alarm.com.
2
---- Refresh Thermostat Requests updated thermostat data.
1
All Image Sensor menus are only available when an Image Sensor
daughterboard has been connected to the module. An Image Sensor
daughterboard is required to enable Image Sensor functionality.
2 TM
Refer to the emPower installation instructions and guides on the
Alarm.com Dealer Site for more information on Z-Wave enrollment and
troubleshooting.
Simon XT/XTi GSM Module V4 Installation Instructions

Specifications

Compatible Simon XT panels with software versions 0.0.H and later and
Simon XTi
Power requirements 6V nominal
Peak current 1.7A
Operating temperature 32 to 120°F (0 to 49°C)
Storage temperature -30 to 140°F (-34 to 60°C)
Max. relative humidity 90% non-condensing
Cellular network Dual-band CDMA/1xRTT
Dimensions (H x W) 4 1/16 x 1 7/8 in.
Listings FCC Part 15, Verizon Certified

Regulatory Information

Changes or modifications not expressly approved by Alarm.com can void the
user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different form that
which the receiver is connected
-Consult the dealer or an experienced radio/TV technician for help.
Operation is subject to the following two conditions:
(1) This device may not cause interference
(2) This device must accept any interference, including interference that may
cause undesired operation of the device
This equipment complies with the FCC RF radiation exposure limits set forth
for an uncontrolled environment. This equipment should be installed and
operated with a minimum distance of 20 centimeters between the radiator
and your body.
FCC IDs: YL6-143200C5V4IS, IC: 9111A-143200C5V4IS
This device contains FCC ID: RI7CC864-DUAL, IC: 5131A-CC864-DUAL
7