Interlogix Simon XT Installation Instructions Manual page 6

Table 5: Interactive Services on Simon XTi
Menu Description
System Programming + Scroll to Programming. Enter the Installer
Installer Code Code
- Interactive Services Select Interactive Services.
-- Module Status Provides status and troubleshooting
information for the CDMA module.
1
-- Image Sensor Enroll, troubleshoot and configure Image
Sensors. This menu can also be used to
retrieve images from the enrolled Image
Sensors.
1
---Status View signal strength, PIR, battery and
other information about each Image
Sensor enrolled.
1
----Set PIR Sensitivity View and configure the PIR sensitivity for
the Image Sensor.
1
---Privacy Remove all Image Sensor images currently
stored on the XTi panel. (This does not
affect image storage on the Alarm.com
online account.)
1
--- Add Enroll the Image Sensor by inserting
batteries or resetting.
1
---Image List View list of images captured by the Image
Sensor(s) on the system and request to
have specific images sent to the panel for
local viewing.
1
--- Test Put the Image Sensor in PIR Test Mode
(LED on sensor illuminates when
activated) or request an "Installer Peek-In
Now" to test image captures.
1
--- Delete Delete Image Sensors from the panel.
--Set Dealer Logo Send the dealer logo to the panel and .
(Only available for dealers who have set
up this feature with Alarm.com.)
-- Weather Update Request a Weather Update if the weather
forecast is not showing on the XTi touch
screen. To speed up the process, stay in
Programming. This keeps the panel in
high-speed communication mode with the
touch screens.
2
-- Z-Wave to add, remove, and troubleshoot Z-Wave
devices and networks. To control Z-Wave
devices via the Alarm.com website and
smart phone apps, you will also need to
enable Z-Wave services on the account.
2
--- Add Device Add Z-Wave devices to the module's
network. Make sure the device you are
trying to add is powered up and within 3
to 6 feet of the Simon XTi panel. Read the
manufacturer's instructions on what
button to press on the device to enroll it.
2
--- Remove Device Remove an existing Z-Wave device, or to
"reset" a Z-Wave device that was
previously learned into a different Z-Wave
network, before you can learn it into the
CDMA module.
---Update 2WTTS Press Update 2WTTS to force an update of
the thermostat, lights or locks information
shown on the touch screen (2WTTS). Note
that these updates may take several
Simon XT/XTi GSM Module V4 Installation Instructions
minutes to complete.
----Thermostats View thermostat data and update/remove
thermostats from display on the panel
and touch screens.
----Lights Update the lights list shown on the panel
and touch screens.
----Locks Update locks list shown on panel and
touch screens and pair locks with their
door contact sensor.
2
--- Advanced Provides additional functionality for
advanced Z-Wave troubleshooting and
configuration.
2
---- Rediscovery Network rediscovery allows the system to
determine the most efficient
communication patch between Z-Wave
devices. (During this process the Z-Wave
network is busy and cannot respond to
other commands.)
2
---- Replicate Mode Initiates replicate mode on the panel.
2
---- Send Node Info For advanced use only. Do not use unless
directed to do so by Alarm.com.
2
---- Refresh Thermostat Requests updated thermostat data.
--Advanced Menu This menu houses advanced CDMA
module tasks.
---Auth. Code Requests an authorization code from
Alarm.com for use on the Image Sensor
Installer Test Site
(www.alarm.com/imagesetup).
---Create Account This menu is available only to installers
who have their own Alarm.com account
creation system. You must enter a
Technician ID and a Lead ID in order to use
this menu.
System Programming + Scroll to Programming. Enter the Master
Master Code Code
- Interactive Services Select Interactive Services.
-- Module Status Provides status and troubleshooting
information for the CDMA module.
-- Image Sensor This menu is used to view the status of
and test Image Sensors. This menu can
also be used to retrieve images from the
enrolled Image Sensors.
---Status View signal strength, PIR, battery and
other information about each Image
Sensor enrolled.
---Privacy Clear all Image Sensor images currently
stored on the XTi panel. (This does not
affect image storage on the Alarm.com
online account.)
---Image List View list of images captured by the Image
Sensor(s) on the system and request to
have specific images sent to the panel for
local viewing.
--- Test Put the Image Sensor in PIR Test Mode
(LED on sensor illuminates when
activated) or request an "Installer Peek-In
Now" to test image captures.
-- Weather Update Request a Weather Update if the weather
forecast is not showing on the XTi touch
6