Connecting Pluggable Transceivers To The Sfp And Sfp+ Ports - Enterasys SSA-T1068-0652 Hardware Installation Manual

Connecting Pluggable Transceivers to the SFP and SFP+ Ports

This section describes how to install an SFP or SFP+ pluggable transceiver in any of the SSA SFP or
SFP+ ports. For a list of supported SFP and SFP+ pluggable transceivers and their specifications,
refer to the S‐Series firmware Release Notes for the latest compatibility matrix for SFP and SFP+
pluggable transceivers. You can also refer to the datasheet located at the following URL:
http://www.enterasys.com/products/transceivers‐ds.pdf
Warning: Fiber-optic SFPs and SFP+s use Class 1 lasers. Do not use optical instruments to view
the laser output. The use of optical instruments to view laser output increases eye hazard. When
viewing the output optical port, power must be removed from the network adapter.
Advertencia: Los transmisores receptores de fibra óptica SFP y SFP+ conectables utilizan
sistemas de láser clase 1. No emplee instrumentos ópticos para ver la salida del láser. Hacerlo
podría incrementar el riesgo de daño en los ojos. Cuando se revise el puerto óptico de salida,
deberá cortarse la energía del adaptador de red.
Warnhinweis: Faseroptische, steckbare Transceiver der Typen SFP und SFP+ verwenden Laser
der Klasse 1. Zur Ansicht der Laserausgabe dürfen keine optischen Geräte verwendet werden, da
hierdurch die Wahrscheinlichkeit einer Gefährdung der Augen erhöht wird. Vor der Inspektion des
optischen Ausgangsanschlusses muss das Stromkabel des Netzwerkadapters herausgezogen
werden.
Caution: Carefully follow the instructions in this manual to avoid damaging the SFP, SFP+, and
SSA.
The SFP, SFP+, and SSA are sensitive to static discharges. Use an antistatic wrist strap and
observe all static precautions during this procedure. Failure to do so could result in damage to the
SFP, SFP+, and SSA. Always leave the SFP or SFP+ in the antistatic bag or an equivalent
antistatic container when not installed.
Precaución: Siga las instrucciones del manual para no dañar el SFP, SFP+ ni el SSA, puesto que
son muy sensible a las descargas de electricidad estática.
Utilice la pulsera antiestática y tome todas las precauciones necesarias durante este
procedimiento. Si no lo hace, podría dañar el SFP, SFP+ o el SSA. Mientras no esté instalado,
mantenga el SFP o SFP+ en su bolsa antiestática o en cualquier otro recipiente antiestático.
Preparation
Before installing the pluggable transceiver, proceed as follows:
1. Put on the antistatic wrist strap and attach it to the ground receptacle on the front of the SSA
before removing the pluggable transceiver from the anti‐static packaging. Refer to the
instructions in the anti‐static wrist strap package. See Figure
of the ground receptacle.
2. Remove the pluggable transceiver from the packaging.
3. If there is a protective dust cover on the pluggable transceiver, do not remove it at this time.
Installing the Pluggable Transceiver
To install an SFP or SFP+ pluggable transceiver in the SSA:
1. Hold the pluggable transceiver so that the connector will seat properly.
2. Carefully align the pluggable transceiver with the port.
3. Push the pluggable transceiver into the port until the pluggable transceiver clicks and locks
into place.
Enterasys S-Series Stand Alone (SSA) Hardware Installation Guide 2-17
Connecting to the Network
2‐9 on page 2‐13 for the location