Select whether to display the waste toner full warning as a drum replacement required message or as E019 displayed on an operator call. Select 1 to display a rum

replacement required message on an operator call. Select 0 to display E019 on an service call.

5.1.2 Menu Switch Settings (MENU)

5.1.2.1 Menu Switch Composition

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

No.

005

006

007

008

009

010

5.1.2.2 <No.005 NL equalizer>

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Use it to enable-disable the NL equalizer.

If errors occur often during communication because of the condition of the line, enable (ON) the NL equalizer.

Any of the following error codes may be indicated at time of transmission because of the line condition:

##100, ##101, ##102, ##104, ##201, ##281, ##282, ##283, ##750, ##755, ##765, ##774, ##779, ##784, ##789

Any of the following error codes may be indicated at time of transmission because of the line condition:

##103, ##107, ##114, ##201, ##790, ##793

5.1.2.3 <No.006 telephone line monitor>

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Use it to s the telephone line monitor function:

DIAL: generate the monitor sound of the telephone line using the speaker from the start of transmission to DIS.

SERVICEMAN [1]: generate the monitor sound of the telephone line using the speaker from the start of communication to the end of it.

SERVICEMAN [2]: generate the monitor sound of the telephone line2 (Option).

OFF: do not generate the monitor sound of the telephone line using the speaker.

5.1.2.4 <No.007 ATT transmission level>

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Use it to set the transmission level (ATT).

Raise the transmission level if errors occur frequently at time of communication because of the condition of the line. (It means close to 8)

Any of the following error codes may be indicated at time of transmission because of the line condition:

##100, ##101, ##102, ##104, ##201, ##280, ##281, ##282, ##283, ##284, ##750, ##752, ##754, ##755, ##757, ##759, ##760, ##762, ##764, ##765,

##767, ##769, ##770, ##772, ##774, ##775, ##777, ##779, ##780, ##782, ##784, ##785, ##787, ##789

Any of the following error codes may be indicated at time of reception because of the line condition:

##103, ##106, ##107, ##201, ##793

5.1.2.5 <No.008 V.34 modulation speed upper limit>

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Use it to set an upper limit to the modulation speed (baud rate) for the V.34 primary channel.

5.1.2.6 <No.009 V.34 data speed upper limit>

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

Use it to set an upper limit to the data transmission speed for the V.34 primary channel between 2.4K and 33.6K bps in increments of 2400 bps. (0: 2.4K to 13:

33.6K bps).

5.1.2.7 <No.010 Frequency of the pseudo CI signal>

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i

You may select a frequency for the pseudo CI signal.

Some types of external telephones do not ring when the fax/tel switch-over function is ON. To sound the ring, change the pseudo CI signal.

Function

Range of settings

NL equalizer

1: ON, 0: OFF

telephone line monitor

0:DIAL, 1:SERVICEMAN1, 2:SERVICEMAN2, 3:OFF

transmission level (ATT)