Test Mode Menu List (Touch Panel Type) - Canon iR2030 Portable Manual

Chapter 5
Numerals enclosed in parentheses denote a numeric keypad key to be pressed each.
Group Subgroup
(1) FUNCTION TEST G3 4800bps
(3) 6-3 SENSOR [1] - [6]
(4) ADF FEED TEST
(5) BOOK FEED TEST
(6) 6-6 SPEAKER FREQ:[1] VOL:[2]
(7)
(8) FUNCTION TEST LAMP TEST ALL
(9) LINE TEST [1] - [3]
(0) ROLLER CLEAN 0:PRT 1:ADF
(0) PRT ROL CLEAN Press start key
(1) ADF ROL CLEAN Press start key

5.1.17.3 Test Mode Menu List (Touch Panel Type)

iR2022i / iR2018i
Test mode menu list
To invoke test mode, follow these steps:
1) Enter service mode.
Sequentially press the Additional functions key, 2 key, 8 key, and Additional functions key on the operation panel.
2) Press the arrow key on the touch panel to display "TEST MODE".
3) Press [OK].
Numerals enclosed in parentheses denote a numeric keypad key to be pressed each.
Group Subgroup
TEST MODE [1] - [9], [#]
(1) DRAM [1] - [2]
(1) D-RAM TEST
(2) D-RAM TEST
(2) SCAN TEST [1] - [8]
(1) SHADING
(3) SHEET POS ADJ
(4) TRASH DETECT
(5), (6), (9), (*)
(3) PRINT TEST [1] - [9]
(1)
(2)
(3)
(4)
(5), (6), (7), (8), (9), (*)
(4) MODEM TEST [1] - [9]
58
Item 1 Item 2 Item 3
(1) SENSOR CHECK 0:NORMAL 1:LATCH
(0) SENSOR NORMAL [0] - [2]
(0) CAS 0 REG 0 DEL 0 MULTI 0
(1) TONER 0 FULL 0 2ND-DEL 0000
(2) OP1 0000 OP2 0000 OP3 0000 PATH
0000
(1) SENSOR
LATCH [0] -
[2]
(0) CAS 0 REG 0 DEL 0 MULTI 0
(1) TONER 0 FULL 0 2ND-DEL 0000
(2) OP1 0000 OP2 0000 OP3 0000 PATH
0000
(2) SWITCH CHECK [0] - [1]
(0) CAS 0000 LOCK 0000
(1) OP1 0000 OP2 0000 OP3 0000
(3) DS ON DES of HPS ON BCVS of
(4) REF xxx ANT xxx |ANT-REF| xxx
(5) BSCT on BDAC[ A3] BDSS3-0 [ of of of of ]
(6) NCR Sts: NCR xxxxx DPT MGN OK RDY 0101
(7) LAST of EXIT of REG of CVR of
(8) WID1 on WID2 on LEN1 on LEN2 on
(9) D+Temp xxxx E+Hum xxxx F+Temp xxxx xxxx
Item 1 Item 2 Item 3
Explanation
G3 4800 bps signal transmission test
Sensor checks
ADF delivery operation test
Book copy operation test
Speaker volume and buzzer frequency test
Not used
Lamp test
Line signal reception test
Printer and ADF roller cleaning
T-5-33
Explanation
D-RAM data check
Write/read check
Read check
Automatic gain adjustment
CS position adjustment
Dust detection
Not used
Not used
All-black output
Not used
Back belt output
Not used
0017-6195