Numeric Parameter Settings (Numeric Param.); Numerical Parameter Composition; 002: Rtn Transmission Condition (1)><003: Rtn Transmission Condition (2)><004: Rtn Transmission Condition (3); 005: Ncc Pause Length (Pre-Id Code) - Canon iR2030 Portable Manual

Chapter 5

5.1.3 Numeric Parameter Settings (NUMERIC Param.)

5.1.3.1 Numerical Parameter Composition

iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i
5.1.3.2 <002: RTN transmission condition (1)><003: RTN transmission condition (2)><004: RTN transmission condition
(3)>
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i
Use it to set RTN signal transmission conditions. Raise these parameters for more lenient conditions if errors occur frequently at time of reception because of trans-
mission of the RTN signal.
Memo:
Any of the following error codes may be indicated at time of reception because of RTN signal transmission
##0104, ##0107, ##0114, ##0201
RTN signal transmission condition (1) affects the ratio of error lines to the total number of lines per single page of received images.
RTN signal transmission condition (2) affects the standard value (*2) of burst errors (*1).
RTN signal condition (3) affects the number of errors not reaching the standard value of burst errors.
*1: transmission error occurring cover several lines.
*2: for instance, if '15' is set, a single burst error will represent an error occurring continuously cover 15 lines.
If any of these lines is detected while an image signal is being received, the RTN signal will be transmitted after receiving the protocol signal of the transmitting
party. Higher parameters restrict the transmission of the RTN signal.
5.1.3.3 <005: NCC pause length (pre-ID code)>
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i
Use it to set the length of the pause automatically entered between access code and ID code when the NCC (New Common Carrier) line is used for dialing.
5.1.3.4 <006: NCC pause length (post-ID code)>
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i
Use it to set the length of the pause automatically entered between ID code and telephone number of the other party when the NCC (New Common Carrier) line is
used for dialing.
28
No. Item
002 RTN transmission condition(1)
003 RTN transmission condition (2)
004 RTN transmission condition (3)
005 NCC pause time length (pre-ID code)
006 NCC pause time length (post-ID code)
010 line condition identification time length
011 T.30T1 timer (for reception)
013 T.30 EOL timer
015 hooking detection time length
016 time length to first response at time of fax/tel switchover
017 pseudo RBT signal pattern ON time length
018 pseudo RBT signal pattern OFF time length
(short)
019 pseudo RBT signal pattern OFF time length
(long)
020 pseudo CI signal pattern ON time length
021 pseudo CI signal pattern OFF time length
(short)
022 pseudo CI signal pattern OFF time length (long)
023 CNG detection level at time of fax/tel switchover
024 pseudo RBT transmission level at time of fax/tel switchover 10 to 20
025 Answering machine connection function signal detection
time
027 preamble detection time length for V21 low-speed flag
055 acquisition period of environmental log data
056 display the type of soft counter 1
057 Display the type of soft counter 2
058 Display the type of soft counter 3
059 Display the type of soft counter 4
060 Display the type of soft counter 5
061 Display the type of soft counter 6
T-5-18
Range of settings
1% to 99%
2 to 99 item
1 to 99 lines
1 to 60 sec
1 to 60 sec
0 to 9999 (10 msec)
0 to 9999 (10 msec)
500 to 3000 (10 msec)
0 to 999
0 to 9
0 to 999
0 to 999
0 to 999
0 to 999
0 to 999
0 to 999
0 to 7
0 to 20 (120/230V)
0 to 999
20 (x 10ms)
0 to 480 (60min)
101 (Fixed)
0 to 999
0 to 999
0 to 999
0 to 999
0 to 999
0017-6099
0017-6100
0017-6102
0017-6103