NEC NC1700L Installation Manual page 113

Error Code
990 LaserBDEepromFail
992 LDMCULockUp
993 54VError
995 LDEepromFail
996 KEY Switch Off
1000 Slave Comm Fail
1003 Slave Comm Ack Fail
1004 Slave Power Ready Fail
1005 Slave No Notify
1500 P3P3V SAT PGOOD Fail
1501 P2P5V SAT PGOOD Fail
1502 XVT PGOOD Fail
1503 P2P5V X PGOOD Fail
1504 P1P8V X PGOOD Fail
1505 P1V X PGOOD Fail
1506 FMT FPGA DONE Fail
1509 EXGPIO IC602 Fail
1510 EXGPIO IC603 Fail
1511 EXGPIO IC604 Fail
1512 EEPROM IC2800 Write Fail
1513 EEPROM IC601 Read Fail
1514 EEPROM IC601 Write Fail
1515 EEPROM IC601 Write Fail(Verify)
1538 EEPROM IC2800 Read Fail
1550 EEPROM IC2800 Write Fail Verify
2000 IntegrityFail
2010 Incorrect power-off
2100 Diffuser2 Wheel Stop
2101 Diffuser2 Wheel Stop Precaution
2110 OverTemp.LS_G1 Precaution
2111 OverTemp.LS_G2 Precaution
2112 OverTemp.LS_G3 Precaution
2113 OverTemp.LS_G4 Precaution
2114 OverTemp.LS_B Precaution
2115 OverTemp.LS_R Precaution
2120 OverTemp.LS_G1
2121 OverTemp.LS_G2
2122 OverTemp.LS_G3
2123 OverTemp.LS_G4
2124 OverTemp.LS_B
2125 OverTemp.LS_R
2130 SensorFail LS_G_Module1
2131 SensorFail LS_G_Module2
2132 SensorFail LS_G_Module3
2133 SensorFail LS_G_Module4
Error message Description
Data check sum error in EEPROM on LD board.
LD uC is locked up.
54V is abnormal.
Communication error with the EEPROM on LD board.
The laser unit laser administrator switch is off.
Failed to communicate with slave MCU.
Slave fauls to execut the command.
Slave Power Ready error
Slave Power Notify error
Error detected with 3.3V power supply for FSB
Error detected with 2.5V power supply for FSB
Error detected with DDR power supply for FMT FPGA
Error detected with 2.5V power supply for FMT FPGA
Error detected with 1.8V power supply for FMT FPGA
Error detected with 1V power supply for FMT FPGA
FMT FPGA Configuration Error
I2C Device Access Error
I2C Device Access Error
I2C Device Access Error
I2C Device Access Error
I2C Device Access Error
I2C Device Access Error
I2C Device Access Error
I2C Device Access Error
I2C Device Access Error
Integrity error with the internal software code of the
projector.
* When this error has occurred, the projector will not
accept any external demands. Communication with
external devices will not be performed either.
PowerOff was not performed correctly last time.
Diffuser2 Wheel has stopped.
Diffuser2 Wheel Stop Precaution
Set inside temperature (LS_G1) is close to over
temperature.
Set inside temperature (LS_G2) is close to over
temperature.
Set inside temperature (LS_G3) is close to over
temperature.
Set inside temperature (LS_G4) is close to over
temperature.
Set inside temperature (LS_B) is close to over
temperature.
Set inside temperature (LS_R) is close to over
temperature.
Set inside temperature (LS_G1) is abnormal.
Set inside temperature (LS_G2) is abnormal.
Set inside temperature (LS_G3) is abnormal.
Set inside temperature (LS_G4) is abnormal.
Set inside temperature (LS_B) is abnormal.
Set inside temperature (LS_R) is abnormal.
Failed to read LS_G_Module1 sensor.
Failed to read LS_G_Module2 sensor.
Failed to read LS_G_Module3 sensor.
Failed to read LS_G_Module4 sensor.
Appendix
113