Daikin CHYHBH05AA Installer's Reference Manual page 50

Hybrid for multi heat pump – heat pump module
Hide thumbs Also See for CHYHBH05AA:
Table of Contents

Advertisement

8 Configuration
Domestic hot water pump installed for...
Instant hot water
c
a
f
b
g
a
Indoor unit
b
Tank
c
Domestic hot water pump (field supply)
d
Heater element (field supply)
e
Non‑return valve (field supply)
f
Shower (field supply)
g
Cold water
Thermostats and external sensors
NOTICE
If an external room thermostat is used, the external room
thermostat will control the room frost protection. However,
the room frost protection is only possible if the leaving
water temperature control on the unit's user interface is
turned ON.
#
Code
[A.2.2.4]
[C-05]
Contact type main
In external room thermostat control, the
contact type of the optional room
thermostat or heat pump convector for
the main leaving water temperature zone
must be set.
▪ 1 (Thermo ON/OFF): The connected
external room thermostat or heat
pump convector sends the heating
demand by the same signal as it is
connected to only 1 digital input
(preserved for the main leaving water
temperature zone) on the indoor unit
(X2M/1). Select this value in case of a
connection
convector (FWXV).
▪ 2
connected external room thermostat
sends separate heating demand and
is therefore connected to the 2 digital
input (preserved for the main leaving
water temperature zone) on the indoor
unit (X2M/1 and 2). Select this value in
case of connection with the wired
(EKRTWA) or wireless (EKRTR1)
room thermostat.
Remark: Only possible to use as a
heating application.
[A.2.2.5]
[C-06]
Contact type add.
In external room thermostat control with
2 leaving water temperature zones, the
type of the optional room thermostat for
the additional leaving water temperature
zone must be set.
▪ 1 (Thermo ON/OFF): See Contact
type main. Connected on the indoor
unit (X2M/1a).
▪ 2 (H/C request)(default): See Contact
type main. Connected on the indoor
unit (X2M/1a and 2a).
Installer reference guide
50
Disinfection
c
a
d
f
b
e
g
Description
to
the
heat
pump
(H/C
request)(default):
The
#
Code
[A.2.2.B]
[C-08]
External sensor
When an optional external ambient
sensor is connected, the type of the
sensor must be set.
▪ 0 (No)(default): NOT installed. The
thermistor in the user interface and in
the
measurement.
▪ 1 (Outdoor sensor): Installed. The
outdoor
measure
temperature.
functionality, the temperature sensor
in the outdoor unit is still used.
▪ 2
temperature
interface is NOT used anymore.
Remark: This value has only meaning
in room thermostat control.
Digital I/O PCB
Modification of these settings is only needed when the optional
digital I/O PCB is installed. The digital I/O PCB has multiple
functionality which need to be configured.
#
Code
[A.2.2.6.2]
[D-07]
Solar kit
Indicates if the domestic hot water tank
is also heated by thermal solar panels.
▪ 0 (No)(default): NOT installed.
▪ 1 (Yes): Installed. The domestic hot
water tank can –besides by the boiler–
also be heated by thermal solar
panels. Set this value if thermal solar
panels are installed.
[A.2.2.6.3]
[C-09]
Alarm output
Indicates the logic of the alarm output on
the digital I/O PCB during
malfunctioning.
▪ 0 (Normally open): The alarm output
will be powered when an alarm
occurs. By setting this value, a
distinction
detection
detection of a power failure.
▪ 1 (Normally closed): The alarm output
will NOT be powered when an alarm
occurs.
See also table below (Alarm output
logic).
Alarm output logic
[C-09]
Alarm
0 (default)
Closed output
1
Open output
Savings mode
The user can choose whether switching between operation modes is
either economically or ecologically optimised. Set to Economical, the
system will in all operating conditions select the energy source (gas
or electricity) based on energy prices, resulting in a minimisation of
Daikin hybrid for multi heat pump – heat pump module
Description
outdoor
unit
are
used
sensor
will
be
used
the
outdoor
ambient
Remark:
For
some
(Room
sensor):
Installed.
The
sensor
in
the
user
Description
is
made
between
of
an
alarm,
and
No alarm
No power
supply to unit
Open output
Open output
Closed output
CHYHBH05+08AA + EHYKOMB33A
4P471761-1A – 2017.10
for
to
the
the

Hide quick links:

Advertisement

Table of Contents
loading

This manual is also suitable for:

Ehykomb33aChyhbh08aa

Table of Contents