Menu Functions - PRESIDENT Lincoln II + Owner's Manual

Long press BAND-+10KHz key (21) again to
disappears from the LCD.
22) 6 PIN MICROPHONE PLUG
The plug is located on the front panel of the transceiver and makes the set-
ting of the equipment into the dashboard easier.
See Cabling Diagram page 51.
23) PTT
Transmission key, press to transmit a message, "TX" is displayed and release
to listen to an incoming communication.
A) DC-POWER TERMINAL (13,8 V)
B) ANTENNA CONNECTOR (SO-239)
C) EXTERNAL SPEAKER JACK (8 Ω, Ø 3,5 mm)
D) JACK FOR OPTIONAL PA (Public Address) (Ø 3.5 mm)
E) JACK FOR OPTIONAL VOX MIKE (Ø 2.5 mm)
F) JACK FOR CW DEVICE (Ø 3.5 mm)
G) USB DATA (PC setting in option)
C) MENU FUNCTIONS
Press the MENU key (4) for 2 seconds to
"FUNC" appears on the LCD.
select
Use s/t keys (10) to the desired function.
Use rotary PUSH knob (6) to set
Press any key except PUSH knob (6) or wait for 5 seconds to
"FUNC" disappears from the LCD.
1) ROGER BEEP FREQUENCY
Set the FREQUENCY of the ROGER BEEP.
At [ ] menu, rotate PUSH knob (6) to
Frequency range: Hz ~ 3 Hz, stepping frequency:
300 000
Press PUSH knob (6) to change
2) ROGER BEEP TIME
Set the TIME (ms) of the ROGER BEEP.
At [ ] menu, rotate PUSH knob (6) to
Time range ~ 1 ms, time stepping:
50 000
(6) to change the step.
disable frequency +10KHZ. "10K"
enter in the menu function setting.
the function.
store
set the Frequency.
Hz, default:1
10
the step.
set the delay Time.
ms. Press PUSH knob
ms, default:
50 500
3) CW FREQUENCY
Set the FREQUENCY of the CW.
At [ ] menu, rotate PUSH knob (6) to
Frequency range:
Press PUSH knob (6) to change the step.
4) CALL FREQUENCY
Set the FREQUENCY of the CALL tone.
At [ ] menu, rotate PUSH knob (6) to
Frequency range:
Press PUSH knob (6) to change the stepping.
5) MONITOR GAIN VOLUME
Set the OUTPUT VOLUME LEVEL of the microphone in your own speaker.
] menu, rotate PUSH knob (6) to
At [
There are 32 levels. "OFF"
6) TOT (Time Out Timer)
Set the TOT. If the PTT pedal (23) is pressed for more than "TOT" time, the
transmission ends.
At [ ] menu, rotate PUSH knob (6) to
tion. Time range 3
7) SWR PROTECTION
Enable/disable the SWR PROTECTION.
At [ ] menu, rotate PUSH knob (6) to
protection. Default: "
and exit.
8) SWR PROTECTION SETTING
Set the SWR LEVEL PROTECTION.
At [ ] menu, rotate PUSH knob (6) to
Level range: ~ 2
12
the step. The SWR level is useful only in the SWR protection function is active.
Hz.
050
9) VOLTAGE PROTECTION
Enable/disable VOLTAGE PROTECTION.
At [ ] menu, rotate PUSH knob (6) to
the protection. Default: "
10) VOLTAGE PROTECTION HIGH
Set the HIGHER LIMIT of VOLTAGE PROTECTION.
11
set the Frequency.
Hz ~ 3 Hz, stepping frequency:
300 000
set the Frequency.
Hz ~ 3 Hz, stepping frequency:
300 000
set the Monitor volume level.
disable the function.
set the TOT, "
~ 60 s, time stepping: 3 s, default: 18
0 0 0
enable "
".
set the protection Level.
. Press PUSH knob (6) to change
, stepping: , default: 2
00 1 00
enable
".
Hz, default:1 Hz.
10 050
Hz, default:1 Hz.
10 050
" disable the func-
s.
0
" or disable " " the
" " or disable " "