Function With The Ptt Switch; Menu - PRESIDENT George II Owner's Manual

D) FUNCTIONS WITH THE PTT SWITCH
1) TALKBACK LEVEL
This function allows to adjust the volume level of the TALKBACK.
1. Activate the TALKBACK function.
2. Press and hold the PTT switch (18) then turn the CH rotary knob (4) to
crease (clockwise) / decrease
TALKBACK.
3. Release the PTT switch (18).
E) MENU
The order of 23 menus is as described in this manual. However, the menu
displayed by entering the MENU will be the last menu modified by user.
The procedure is the same whatever the function is:
Long Press PUSH key (4) to enter
1. Turn the CH rotary knob (4) or use UP/DN keys (19) on the microphone to
select the menu to set.
2. Press PUSH key (4) to validate.
3. Turn the CH rotary knob (4) or use UP/DN keys (19) on the microphone to
modify the value of the parameter.
4. New press on PUSH key (4) to
stops blinking and if the function has more than one parameter, the next
parameter blinks.
5. exits
If no key is pressed, the unit
from the display.
Note: UP/DN keys (19) on the microphone have the same effect as the
rotation of the CH rotary knob (4). PTT switch (18)
exists

MENU.

and disappears.
1) COLOR
Long Press PUSH key (4) to enter
1. Turn the CH rotary knob (4) or use UP/DN keys (19) on the microphone to
select the menu.
2. Press PUSH key (4) to validate.
3. Turn the CH rotary knob (4) or use UP/DN keys (19) on the microphone to
modify
the color of the display.
(counterclockwise) the volume level of the
the MENU. is displayed.
The current color blinks on the display.
validate
the chosen value. The parameter
MENU after 10 seconds.
disappears
validates the last setting
the MENU. is displayed.
The current color blinks on the display.
4. Short press PUSH key (4) to validate. a) Return to the point 1 to set another
menu or b) Short press the PTT key (18) to
disappears from the display.
5. If no key is pressed, the unit
from the display.
Default COLOR is:
(orange).
in-
2) DIMMER
DIMMER function allows
from 0 to 9.
Long Press PUSH key (4) to
1. Turn the CH rotary knob (4) or use UP/DN keys (19) on the microphone to
select
the menu.
2. Press PUSH key (4) to validate.
3. Turn the CH rotary knob (4) or use the UP/DN keys (19) on the microphone
to change the value of the dimmer.
4. Short press PUSH key (4) to validate. a) Return to the point 1 to set another
menu or b) Short press the PTT key (18) to
disappears from the display.
5. If no key is pressed, the unit
from the display.
Dimmer default value is : 5.
3) TONE
This function allows to change
Long Press PUSH key (4) to
1. Turn the CH rotary knob (4) or use UP/DN keys (19) on the microphone to
select
the menu.
2. Press PUSH key (4) to validate.
3. Turn the CH rotary knob (4) or use the UP/DN keys (19) on the microphone
to change the value of the tone.
4. Short press PUSH key (4) to validate. a) Return to the point 1 to set another
menu or b) Short press the PTT key (18) to
disappears from the display.
5. If no key is pressed, the unit
from the display.
Tone default value is : 0
4) KEY BEEP
When the function is activated, a beep
51
validate and exit
exits MENU after 10 seconds.
adjusting
the brightness of the lighting. 10 steps
enter the MENU. is displayed.
The current value blinks on the display.
validate exit
and
exits MENU after 10 seconds.
RX
the TONE. 11 steps from -5 to +5
enter the MENU.
is displayed.
The current value blinks on the display.
validate exit
and
exits MENU after 10 seconds.
sounds when a key is pressed, by
the MENU.
disappears
the MENU.
disappears
the MENU.
disappears